REAR NO. 1 SEAT OUTER BELT ASSEMBLY (for 60/40 Split Seat Type) REMOVAL


  1. ADJUST REAR NO. 2 SEAT ASSEMBLY


    1. A01CE11

      Adjust the rear No. 2 seat assembly so that the positioning marks are aligned as shown in the illustration.

  2. REMOVE RECLINING ADJUSTER RELEASE HANDLE


    1. A01CDR9E01

      Using a screwdriver wrapped with protective tape, disengage the claw and remove the reclining adjuster release handle.

  3. REMOVE UPPER SEAT TRACK RAIL COVER


    1. A01CC1F

      Disengage the 5 claws and clip.

    2. Disengage the 2 guides and remove the upper seat track rail cover.

    3. A01CFZ1

      Disengage the 2 claws and remove the grommet.

  4. REMOVE NO. 1 SEAT TRACK LOCK PLATE COVER


    1. A01CDSK

      Disengage the 2 claws, guide and remove the No. 1 seat track lock plate cover.

  5. REMOVE NO. 2 SEAT HEADREST ASSEMBLY

  6. REMOVE REAR SEAT CENTER HEADREST ASSEMBLY (for LH Side)

  7. REMOVE REAR NO. 2 SEAT ASSEMBLY


    1. Install the 2 stopper bolts in the order of <B>, <A>.

      A01CC4XE01
      Torque:
      21 N*m  { 214 kgf*cm, 16 ft.*lbf }

      Note

      Use service stopper bolts with part numbers 72702-58120 and 72702-58110, or other bolts of an equivalent size (M8 X 1.25).

      Tech Tips

      Stopper bolts sizes are as shown below.

      Recommended Stopper Bolt
      Part Length
      A 14 mm (0.551 in.)
      B 15.5 mm (0.610 in.) or more
      C 10 mm (0.394 in.) or less
      D 72702-58110 Bolt <A> 45.7 mm (1.80 in.)
      72702-58120 Bolt <B> 61.2 mm (2.41 in.)
      E 72702-58110 Bolt <A> 27.7 mm (1.09 in.)
      72702-58120 Bolt <B> 48.2 mm (1.90 in.)
      F 18 mm (0.709 in.)
      G 2.5 mm (0.0984 in.) or less
      H 1.0 mm (0.0394 in.) or less
      I 0.75 mm (0.0295 in.) or less
      J 5.5 mm (0.217 in.)
    2. A01CBYV

      Remove the 2 nuts and disconnect the rear No. 2 seat outer belt assembly.

    3. Remove the rear No. 2 seat assembly.

      Note

      Do not damage the rear No. 2 seat assembly, body or body interior.

  8. REMOVE BACK DOOR STRIKER COVER


    1. A01CDGVE02
      Text in Illustration
      *1 Protective Tape

      Using a screwdriver, disengage the 4 claws and 2 guides, and remove the back door striker cover.

      Tech Tips

      Tape the screwdriver tip before use.

  9. REMOVE BACK DOOR SCUFF PLATE


    1. A01CCY0

      Remove the 4 claws, 4 clips and 2 guides, and remove the back door scuff plate.

  10. REMOVE REAR DOOR SCUFF PLATE


    1. Captain type rear seat:


      1. A01CFIB

        Disengage the 9 claws, 9 clips and 2 guides, and remove the rear door scuff plate RH.

    2. Tip-up type rear seat:


      1. A01CGAPE02
        Text in Illustration
        *1 Protective Tape

        Apply protective tape to the bottom of the seat as shown in the illustration.

      2. A01CEQB

        Using the slide lever, slide the rear No. 1 seat to the rearmost position.

      3. Disengage the 4 clips, 5 claws and guide on the front side of the scuff plate as shown in the illustration.

        Note

        To prevent damage to the scuff plate, make sure not to use excessive force when disengaging the clips, claws and guide.

      4. A01CETW

        Using the reclining lever or foot-operated walk-in pedal, tip up the rear No. 1 seat and slide it to the foremost position.

      5. Disengage the 5 clips, 4 claws and guide on the rear side of the scuff plate as shown in the illustration, and remove the rear door scuff plate RH.

        Note

        To prevent damage to the scuff plate, make sure not to use excessive force when disengaging the clips, claws and guide.

  11. DISCONNECT NO. 1 SLIDE DOOR WEATHERSTRIP

  12. REMOVE LUGGAGE COMPARTMENT TRIM HOOK


    1. A01CDVME01

      Turn the No. 1 luggage compartment trim hook clockwise approximately 90° and pull it out as shown in the illustration.

    2. A01CAW1

      Remove the bolt and No. 1 luggage compartment trim hook.

  13. REMOVE ROPE HOOK ASSEMBLY


    1. A01CE61E02
      Text in Illustration
      *1 Protective Tape

      Using a screwdriver, disengage the 2 claws.

      Tech Tips

      Tape the screwdriver tip before use.

    2. Remove the bolt and the rope hook assembly.

  14. REMOVE INNER LUGGAGE COMPARTMENT TRIM COVER


    1. A01CGI2

      Disengage the 4 claws and remove the inner luggage compartment trim cover RH as shown in the illustration.

  15. DISCONNECT REAR NO. 1 SEAT OUTER BELT ASSEMBLY


    1. A01CEZD

      Remove the bolt and disconnect the floor end of the rear No. 1 seat outer belt assembly.

  16. REMOVE DECK SIDE GARNISH RH (for RH Side)


    1. A01CAO7E01

      Disengage the 11 claws and 4 guides, and remove the deck side garnish RH as shown in the illustration.

  17. REMOVE DECK SIDE GARNISH LH (for LH Side)


    1. A01CD2TE01

      Disengage the 12 claws and 4 guides, and remove the deck side garnish LH as shown in the illustration.

  18. REMOVE REAR QUARTER TRIM PANEL ASSEMBLY RH (for RH Side)


    1. Remove the clip.

    2. Disengage the 14 clips, 7 claws and 2 guides.

    3. Disconnect the connectors, and remove the rear quarter trim panel assembly RH.

      A01CBNX

  19. REMOVE REAR QUARTER TRIM PANEL ASSEMBLY LH (for LH Side)


    1. Remove the clip.

    2. Disengage the 15 clips, 8 claws and 2 guides, and remove the rear quarter trim panel assembly LH.

      A01CEOA

  20. REMOVE QUARTER LOCK PILLAR GARNISH


    1. for 60/40 Split Seat Type:


      1. A01CB61

        Disengage the 3 clips and 2 guides, and remove the quarter lock pillar garnish RH.

    2. except 60/40 Split Seat Type:


      1. A01CFEB

        Disengage the 3 clips and 2 guides, and remove the quarter lock pillar garnish RH.

      2. A01CCZ7

        Disengage the 3 claws and 3 guides from backside of the garnish.

      3. Pull the floor anchor part of the rear No. 1 outer seat belt assembly RH toward the quarter lock pillar garnish RH, and then remove the garnish.

  21. REMOVE REAR NO. 1 SEAT OUTER BELT ASSEMBLY


    1. A01CEQWE01

      Loosen the bolt <A> and disconnect the shoulder anchor of the rear No. 1 seat outer belt assembly.

    2. Remove the bolt <B> and rear No. 1 seat outer belt assembly.