Click here

REAR NO. 1 SEAT OUTER BELT ASSEMBLY (for Power Captain Seat) INSTALLATION

Click here
Click here Click here
  1. Click here

    INSTALL REAR NO. 1 SEAT 3 POINT TYPE BELT ASSEMBLY


    1. A01CDUS

      Install the rear No. 1 seat 3 point type belt assembly with the nut.

      42 N*m 428 kgf*cm 31 ft.*lbf
    2. A01CFJTE01

      Insert a pin punch into the zero point calibration hole of the reclining sensor.

    3. With the pin punch inserted, install the reclining sensor with the 3 nuts.

      4.5 N*m 46 kgf*cm 40 in.*lbf

    4. Remove the pin punch.

  2. Click here

    INSTALL NO. 2 REAR SEAT SHOULDER BELT HOLE COVER


    1. A01CDCO

      Engage the 4 claws to install the No. 2 rear seat shoulder belt hole cover.

  3. Click here

    INSTALL REAR NO. 1 SEAT PROTECTOR


    1. A01CAOJ

      Insert the 3 guides.

    2. Install the rear No. 1 seat protector with the 2 clips.

  4. Click here

    INSTALL NO. 1 SEATBACK COVER WITH PAD


    1. Temporarily install the rear No. 1 seatback cover with pad to the rear No. 1 seatback frame sub-assembly.

    2. A01CC2G

      Engage the 4 claws to install the 2 rear seat headrest supports.

    3. A01CFCGE02

      Close the 2 fasteners.

    4. Using hog ring pliers, install the rear No. 1 seatback cover with pad with 3 new hog rings.

      Note:

      • Be careful not to damage the cover.

      • When installing the hog rings, take care to minimize wrinkles as much as possible.

  5. Click here

    INSTALL REAR SEAT LOCK CONTROL LEVER SUB-ASSEMBLY


    1. A01CDJF

      Connect the 2 cable clamps.

    2. Install the rear seat lock control lever sub-assembly with the 2 screws.

  6. Click here

    INSTALL SEAT STAND FRAME CAP


    1. A01CEXX

      Engage the 2 claws to install the seat stand frame cap.

  7. Click here

    INSTALL REAR SEAT SHOULDER BELT COVER


    1. A01CCKP

      Install the rear seat shoulder belt cover with the 2 screws.

  8. Click here

    INSTALL REAR SHOULDER BELT ANCHOR COVER


    1. A01CG8A

      Engage the 4 claws to install the rear shoulder belt anchor cover.

  9. Click here

    INSTALL FRONT SHOULDER BELT ANCHOR COVER


    1. A01CFKZ

      Engage the guide.

    2. Engage the 2 claws to install the front shoulder belt anchor cover.

  10. Click here

    INSTALL NO. 1 SEAT CUSHION COVER WITH PAD


    1. A01CEU7

      Engage each hook.

    2. A01CDMS

      Engage the 9 hooks.

    3. A01CER1

      Engage the 3 hooks to install the rear No. 1 seat cushion cover with pad.

  11. Click here

    INSTALL NO. 6 REAR SEAT LEG SIDE COVER


    1. A01CCAI

      Engage the claw.

    2. Install the No. 6 rear seat leg side cover with the screw.

  12. Click here

    INSTALL NO. 5 REAR SEAT LEG SIDE COVER


    1. A01CE5S

      Engage the claw.

    2. Install the No. 5 rear seat leg side cover with the screw.

  13. Click here

    INSTALL LOWER REAR SEAT LEG COVER


    1. A01CCUR

      Engage the 6 claws.

    2. Install the lower rear seat leg cover with the 2 screws.

  14. Click here

    INSTALL NO. 3 REAR SEAT LEG SIDE COVER


    1. A01CC94

      Engage the 2 claws and guide to install the No. 3 rear seat leg side cover.

  15. Click here

    INSTALL NO. 2 REAR SEAT LEG SIDE COVER


    1. A01CG3A

      Engage the 2 claws and guide to install the No. 2 rear seat leg side cover.

  16. Click here

    INSTALL NO. 3 RECLINING ADJUSTER INSIDE COVER


    1. A01CFJ9

      Engage the 2 claws.

    2. Install the No. 3 reclining adjuster inside cover LH with the screw.

  17. Click here

    INSTALL REAR SEAT ARMREST FRAME SUB-ASSEMBLY


    1. A01CFRHE01

      Engage the clip and the guide.

    2. Install the 4 bolts.

      Bolt <A>, Bolt <B>
      32 N*m 326 kgf*cm 24 ft.*lbf

    3. Install the rear seat armrest frame sub-assembly with the 2 nuts.

      32 N*m 326 kgf*cm 24 ft.*lbf
  18. Click here

    INSTALL CUP HOLDER ASSEMBLY WITH COVER BEZEL


    1. A01CG8F

      Engage the 2 guides.

    2. Engage the 2 claws.

    3. Install the 2 screws.

    4. Install the cup holder assembly with cover bezel with the 2 bolts.

  19. Click here

    INSTALL REAR SEAT ARMREST ASSEMBLY LH


    1. A01CEVD

      Install the rear seat armrest assembly LH with the 4 bolts.

      32 N*m 326 kgf*cm 24 ft.*lbf
  20. Click here

    INSTALL REAR NO. 1 SEAT INNER BELT ASSEMBLY


    1. A01CEBNE01

      Install the rear No. 1 seat inner belt assembly with the bolt and washer.

      42 N*m 428 kgf*cm 31 ft.*lbf
      Note:

      Do not allow the anchor part of the rear No. 1 seat inner belt assembly to overlap the protruding parts of the floor panel.

  21. Click here

    INSTALL REAR SEAT CUSHION MOULDING


    1. A01CG8V

      Engage the 2 guides.

    2. Engage the 4 clips.

    3. Engage the 5 claws.

    4. Install the rear seat cushion moulding with the 2 bolts.

  22. Click here

    INSTALL NO. 4 SEAT ADJUSTER COVER CAP


    1. A01CD9W

      Engage the guide and the claw to install the No. 4 seat adjuster cover cap.

  23. Click here

    INSTALL NO. 3 SEAT ADJUSTER COVER CAP


    1. A01CDHW

      Engage the guide and the claw to install the No. 3 seat adjuster cover cap.

  24. Click here

    INSTALL SEAT ADJUSTER COVER LH


    1. A01CC31

      Engage the 4 guides.

    2. Engage the 6 claws to install the seat adjuster cover cap LH.

  25. Click here

    INSTALL NO. 1 SEAT ADJUSTER COVER CAP (for RH Side)


    1. A01CFWB

      Engage the 2 claws to install the 2 No. 1 seat side adjuster cover caps.

  26. Click here

    INSTALL REAR SEAT SIDE TABLE (for RH Side)


    1. A01CB0P

      Install the rear seat side table with the 2 nuts and 2 bolts.

    2. A01CFTC

      Engage the hook to store the table.

    3. A01CG3R

      Secure the rear seat side table clip with the screw.

  27. Click here

    INSTALL REAR SEAT SIDE TABLE BOARD (for RH Side)


    1. A01CCCU

      Engage the 6 clips to install the rear seat side table board.

  28. Click here

    INSTALL NO. 2 SEAT ADJUSTER COVER CAP (for RH Side)


    1. A01CEPE

      Engage the 2 claws and the 2 guides to install the No. 2 seat side adjuster cover cap.

  29. Click here

    INSTALL REAR SEAT SIDE TABLE COVER (for RH Side)


    1. A01CGAW

      Engage the guide and the claw to install the rear seat side table cover.

  30. Click here

    INSTALL REAR NO. 1 SEAT ARMREST ASSEMBLY RH WITH FRAME AND COVER


    1. A01CCRT

      Install the rear No. 1 seat armrest assembly RH with frame and cover with the 4 nuts.

      32 N*m 326 kgf*cm 24 ft.*lbf

    2. Engage the clamp.

  31. Click here

    CONNECT REAR NO. 1 SEAT 3 POINT TYPE BELT ASSEMBLY


    1. A01CF8NE01

      Connect the rear No. 1 seat 3 point type belt assembly with the bolt.

      42 N*m 428 kgf*cm 31 ft.*lbf
      Note:

      Do not allow the anchor part of the rear No. 1 seat 3 point type belt assembly to overlap the protruding parts of the cushion frame.

  32. Click here

    INSTALL RECLINING ADJUSTER COVER RH


    1. Connect the connector of the rear power seat switch.

    2. Connect the cable of the rear seat lock control lever sub-assembly.

    3. A01CB5KE01

      Place the reclining adjuster cover RH onto the seat in the direction indicated by arrow (1) in the illustration.

    4. Slide the reclining adjuster cover RH in the direction indicated by arrow (2) in the illustration to engage the 2 guides.

    5. Engage the 3 clips.

    6. Install the 4 screws.

    7. Install the reclining adjuster cover RH with the 2 bolts.

  33. Click here

    INSTALL NO. 1 SEAT ADJUSTER COVER CAP


    1. A01CC13

      Engage the guide and the claw to install the No. 1 seat adjuster cover cap.

  34. Click here

    INSTALL NO. 2 SEAT ADJUSTER COVER CAP


    1. A01CD2X

      Engage the guide and the claw to install the No. 2 seat adjuster cover cap.

  35. Click here

    INSTALL NO. 3 RECLINING ADJUSTER INSIDE COVER RH


    1. A01CAMP

      Engage the 3 claws and 2 clips to install the No. 3 reclining adjuster inside cover RH.

  36. Click here

    INSTALL SEAT ADJUSTER COVER RH


    1. A01CDZ2

      Engage the 4 guides and the 6 claws to install the seat adjuster cover cap RH.

  37. Click here

    INSTALL REAR SEAT CUSHION


    1. A01CFJA

      Install the rear seat cushion with the screw.

  38. Click here

    INSTALL NO. 1 RECLINING ADJUSTER RELEASE HANDLE


    1. A01CB26

      Engage the claw to install the No. 1 reclining adjuster release handle.

  39. Click here

    INSTALL REAR NO. 1 SEAT ASSEMBLY


    1. Place the rear No. 1 seat assembly in the cabin.

      Note:

      Be careful not to damage the vehicle body.

    2. Temporary install the rear No. 1 seat assembly with the 4 bolts.

    3. A01CCPRE01

      Install the rear No. 1 seat assembly with the 4 bolts.

      50 N*m 510 kgf*cm 37 ft.*lbf
      Note:

      Tighten the bolts in the order indicated in the illustration.

    4. Install the wiring harness protector set with the nut.

    5. Connect each connector.

    6. A01CDBN

      Engage the 6 claws to close the 2 covers as shown in the illustration.

    7. A01CFEU

      Engage the 6 claws to close the 2 covers as shown in the illustration.

  40. Click here

    INSTALL REAR SEAT LEG COVER


    1. A01CEVN

      Engage the 5 claws and the guide to install the rear seat leg cover.

  41. Click here

    INSTALL REAR SEAT LOWER CUSHION SHIELD


    1. A01CD5A

      Engage the claw and the guide to install the rear seat lower cushion shield as shown in the illustration.

  42. Click here

    INSTALL REAR SEAT HEADREST ASSEMBLY

  43. Click here

    INSPECT REAR NO. 1 SEAT ASSEMBLY


    1. Inspect the power seat operation (Click here).