REAR SEAT CUSHION HEATER INSTALLATION

INSTALL REAR NO. 1 SEAT CUSHION COVER SUB-ASSEMBLY
1. Text in Illustration
  
  *1 Fastener
  
  Using hog ring pliers, temporarily install the rear No. 1 seat cushion cover sub-assembly with 14 new hog rings.
  Note
  
  Be careful not to damage the cover.
  
  Be sure to securely install the hog rings as shown in the illustration while preventing wrinkles from forming on the rear No. 1 seat cushion cover sub-assembly.
2. Engage the 2 fasteners.
3. Using hog ring pliers, install the rear No. 1 seat cushion cover sub-assembly with 3 new hog rings.
  Note
  
  Be careful not to damage the cover.
  
  Be sure to securely install the hog rings as shown in the illustration while preventing wrinkles from forming on the rear No. 1 seat cushion cover sub-assembly.
INSTALL REAR NO. 1 SEAT CUSHION COVER WITH PAD
1. Engage the hook.
2. Engage the 4 claws to connect the seat cushion climate control duct.
3. Engage the 9 hooks.
4. Engage the 3 hooks to install the rear No. 1 seat cushion cover with pad.
INSTALL NO. 6 REAR SEAT LEG SIDE COVER
1. Engage the claw.
2. Install the No. 6 rear seat leg side cover with the screw.
INSTALL NO. 5 REAR SEAT LEG SIDE COVER
1. Engage the claw.
2. Install the No. 5 rear seat leg side cover with the screw.
INSTALL LOWER REAR SEAT LEG COVER
1. Engage the 4 claws.
2. Install the lower rear seat leg cover with the 2 screws.
3. Engage the clamp.
INSTALL NO. 3 REAR SEAT LEG SIDE COVER
1. Engage the 2 claws and guide to install the No. 3 rear seat leg side cover.
INSTALL NO. 2 REAR SEAT LEG SIDE COVER
1. Engage the 2 claws and guide to install the No. 2 rear seat leg side cover.
INSTALL NO. 3 RECLINING ADJUSTER INSIDE COVER
1. Engage the guide.
2. Install the No. 3 reclining adjuster inside cover with the screw.

Text in Illustration
*1	Fastener

INSTALL REAR SEAT ARMREST FRAME SUB-ASSEMBLY

Text in Illustration
*a	Bolt <A>
*b	Bolt <B>
*c	Nut <C>

Engage the clip and guide.

Install the rear seat armrest frame sub-assembly with the 5 bolts and 2 nuts.

Torque:

Bolt <A>

14 N*m { 143 kgf*cm, 10 ft.*lbf }

Bolt <B>

14 N*m { 143 kgf*cm, 10 ft.*lbf }

Nut <C>

14 N*m { 143 kgf*cm, 10 ft.*lbf }

INSTALL REAR POWER SEAT SWITCH WITH CUP HOLDER ASSEMBLY
1. Install the rear power seat switch with cup holder assembly with the 3 bolts and 2 screws.
2. Connect the connector and engage the 2 clamps.
INSTALL REAR SEAT ARMREST ASSEMBLY
1. Engage the guide.
2. Install the rear seat armrest assembly with the 2 bolts.
  
  Torque:
  
  4.5 N*m { 46 kgf*cm, 40 in.*lbf }
INSTALL REAR NO. 1 SEAT INNER BELT ASSEMBLY
1. Text in Illustration
  
  *1 Protruding Part
  
  Install the rear No. 1 seat inner belt assembly with the bolt and washer.
  
  Torque:
  
  42 N*m { 428 kgf*cm, 31 ft.*lbf }
  
  Note
  
  Do not allow the anchor part of the rear No. 1 seat inner belt assembly to overlap the protruding parts of the floor panel.
INSTALL REAR SEAT CUSHION MOULDING
1. Engage the 2 guides.
2. Engage the 5 claws.
3. Engage the 4 clips.
4. Install the rear seat cushion moulding with the 2 bolts.
INSTALL NO. 4 SEAT ADJUSTER COVER CAP
1. Engage the guide and claw to install the No. 4 seat adjuster cover cap.
INSTALL NO. 3 SEAT ADJUSTER COVER CAP
1. Engage the guide and claw to install the No. 3 seat adjuster cover cap.
INSTALL SEAT ADJUSTER COVER CAP LH
1. Engage the 4 guides.
2. Engage the 6 claws to install the seat adjuster cover cap LH.
INSTALL NO. 1 SEAT SIDE ADJUSTER COVER CAP (for RH Side)
1. Engage the 2 claws to install the 2 No. 1 seat side adjuster cover caps.
INSTALL REAR SEAT SIDE TABLE (for RH Side)
1. Install the rear seat side table with the 2 nuts and 2 bolts.
2. Engage the hook to store the table.
3. Secure the rear seat side table clip with the screw.
INSTALL REAR SEAT SIDE TABLE BOARD (for RH Side)
1. Engage the 6 clips to install the rear seat side table board.
INSTALL NO. 2 SEAT SIDE ADJUSTER COVER CAP (for RH Side)
1. Engage the 2 claws and 2 guides to install the No. 2 seat side adjuster cover cap.
INSTALL REAR SEAT SIDE TABLE COVER (for RH Side)
1. Engage the guide and claw to install the rear seat side table cover.
INSTALL REAR NO. 1 SEAT ARMREST ASSEMBLY RH WITH FRAME AND COVER
1. Install the rear No. 1 seat armrest assembly RH with frame and cover with the 4 nuts.
  
  Torque:
  
  14 N*m { 143 kgf*cm, 10 ft.*lbf }
CONNECT NO. 1 SEAT 3 POINT TYPE BELT ASSEMBLY
1. Text in Illustration
  
  *1 Protruding Part
  
  Connect the rear No. 1 seat 3 point type belt assembly with the bolt.
  
  Torque:
  
  42 N*m { 428 kgf*cm, 31 ft.*lbf }
  
  Note
  
  Do not allow the anchor part of the rear No. 1 seat 3 point type belt assembly to overlap the protruding parts of the cushion frame.
INSTALL RECLINING ADJUSTER COVER RH
1. Connect the cable of the rear seat lock control lever sub-assembly.
2. Slide the reclining adjuster cover RH onto the seat in the direction indicated by the arrow (1) in the illustration.
3. Slide the reclining adjuster cover RH in the direction indicated by the arrow (2) in the illustration to engage the 2 guides.
4. Engage the 3 claws and 3 clips.
5. Install the 4 screws.
6. Install the reclining adjuster cover RH with the 2 bolts.
INSTALL NO. 1 SEAT ADJUSTER COVER CAP
1. Engage the guide and claw to install the No. 1 seat adjuster cover cap.
INSTALL NO. 2 SEAT ADJUSTER COVER CAP
1. Engage the guide and claw to install the No. 2 seat adjuster cover cap.
INSTALL NO. 3 RECLINING ADJUSTER INSIDE COVER RH
1. Engage the 3 claws and 2 clips to install the No. 3 reclining adjuster inside cover RH.
INSTALL SEAT ADJUSTER COVER CAP RH
1. Engage the 4 guides and 6 claws to install the seat adjuster cover cap RH.
INSTALL REAR SEAT CUSHION
1. Install the rear seat cushion with the screw.
INSTALL NO. 1 RECLINING ADJUSTER RELEASE HANDLE
1. Engage the claw to install the No. 1 reclining adjuster release handle.
INSTALL REAR NO. 1 SEAT ASSEMBLY

Click here