Click here

REAR NO. 1 SEAT ASSEMBLY (for Luxury Type Power Seat) REASSEMBLY

Click here
Click here Click here
  1. Click here

    INSTALL SEAT CUSHION FELT


    1. A01CDYJ

      Install 2 new seat cushion felts.

  2. Click here

    INSTALL REAR SEAT SIDE TABLE CLIP (for RH Side)


    1. A01CBBY

      Engage the guide.

    2. Temporarily install the rear seat side table clip with the screw.

  3. Click here

    INSTALL NO. 1 SEAT CUSHION PANEL CATCH


    1. A01CFSO

      Engage the 2 claws to install the No. 1 seat cushion panel catch.

  4. Click here

    INSTALL REAR SEAT CUSHION FRAME SUB-ASSEMBLY


    1. A01CCQV

      Install the rear seat cushion frame sub-assembly to the rear No. 1 seat leg sub-assembly with the 5 nuts.

      42 N*m 428 kgf*cm 31 ft.*lbf
  5. Click here

    INSTALL REAR SEAT LOCK HOOK


    1. A01CDCC

      Install the rear seat lock hook with the 3 bolts.

      42 N*m 428 kgf*cm 31 ft.*lbf
  6. Click here

    INSTALL NO. 2 RECLINING ADJUSTER INSIDE COVER LH


    1. A01CDK5

      Install the No. 2 reclining adjuster inside cover LH with the 2 screws.

  7. Click here

    INSTALL NO. 1 SEATBACK FRAME SUB-ASSEMBLY


    1. A01CG8LE01

      Install the No. 1 seatback frame sub-assembly with the 4 bolts.

      Table 1. Text in Illustration
      *a Bolt <A>
      *b Bolt <B>
      Bolt <A>
      42 N*m 428 kgf*cm 31 ft.*lbf
      Bolt <B>
      55 N*m 561 kgf*cm 41 ft.*lbf
  8. Click here

    INSTALL WALK IN SLIDE CONTROL CABLE ASSEMBLY


    1. A01CEYJ

      Connect the 2 cable clamps to the rear seat cushion frame sub-assembly.

    2. Engage the clamp and install the walk in slide control cable assembly.

  9. Click here

    INSTALL RECLINING CONTROL CABLE ASSEMBLY


    1. A01CBD6

      Connect the 4 cable clamps to install the reclining control cable assembly to the rear seat cushion frame sub-assembly.

  10. Click here

    INSTALL SIDE SLIDE CONTROL CABLE ASSEMBLY


    1. A01CDJ9

      Connect the 4 cable clamps to install the side slide control cable assembly to the rear seat cushion frame sub-assembly.

  11. Click here

    INSTALL REAR SEAT WIRE


    1. A01CB39

      Engage the 13 clamps to install the rear seat wire.

  12. Click here

    INSTALL NO. 1 SEAT WIRE


    1. A01CDSU

      Engage the 3 clamps.

    2. Connect the 2 connectors to install the No. 1 seat wire.

  13. Click here

    INSTALL REAR SEAT CLIMATE CONTROL BLOWER


    1. A01CB5E

      Engage the 2 claws to install the rear seat climate control blower to the seat cushion climate control duct.

    2. A01CCQ6

      Engage the claw.

    3. Connect the connector.

    4. Engage the 4 guides.

    5. Install the rear seat climate control blower with duct with the 2 screws.

  14. Click here

    INSTALL REAR SEAT CLIMATE CONTROL ECU


    1. A01CASO

      Install the rear seat climate control ECU with the 2 nuts.

    2. A01CDSO

      Connect the connector.

    3. Engage the 2 clamps.

  15. Click here

    INSTALL POSITION CONTROL ECU ASSEMBLY


    1. A01CD2K

      Install the position control ECU assembly with the 2 nuts.

    2. A01CAL2

      Connect the 2 connectors.

  16. Click here

    INSTALL REAR SEATBACK CLIMATE CONTROL BLOWER


    1. A01CBJQ

      Engage the guide.

    2. Install the rear seatback climate control blower with the 4 screws.

    3. Connect the connector.

  17. Click here

    INSTALL NO. 2 SEATBACK CLIMATE CONTROL DUCT


    1. A01CGAU

      Engage the 2 claws to install the No. 2 seatback climate control duct.

  18. Click here

    INSTALL NO. 1 SEATBACK CLIMATE CONTROL DUCT


    1. A01CDK2

      Install the No. 1 seatback climate control duct with the 4 screws.

  19. Click here

    INSTALL REAR SEATBACK SPRING DAMPER


    1. A01CDYT

      Install the rear seatback spring damper with the 2 nuts.

      19 N*m 194 kgf*cm 14 ft.*lbf
  20. Click here

    INSTALL SEATBACK SPRING DAMPER RH


    1. A01CDNJ

      Install the seatback spring damper RH with the 2 nuts.

      19 N*m 194 kgf*cm 14 ft.*lbf
  21. Click here

    INSTALL RECLINING COVER PROTECTOR


    1. A01CARU

      Install the reclining cover protector with the 2 screws.

  22. Click here

    INSTALL NO. 1 RECLINING COVER PROTECTOR


    1. A01CF6S

      Engage the guide to install the No. 1 reclining cover protector.

  23. Click here

    INSTALL NO. 2 RECLINING COVER PROTECTOR


    1. A01CCUW

      Engage the guide.

    2. Install the No. 2 reclining cover protector with the screw

  24. Click here

    INSTALL NO. 1 RECLINING ADJUSTER INSIDE COVER LH


    1. A01CD4Q

      Engage the guide.

    2. Install the No. 1 reclining adjuster inside cover LH with the 2 screws.

  25. Click here

    INSTALL RECLINING ADJUSTER INSIDE COVER RH


    1. A01CDOY

      Engage the guide.

    2. Install the reclining adjuster inside cover RH with the clip.

  26. Click here

    INSTALL NO. 1 REAR SEAT SHOULDER BELT HOLE COVER


    1. A01CEWD

      Engage the guide.

    2. Engage the 3 claws to install the No. 1 rear seat shoulder belt hole cover.

  27. Click here

    INSTALL NO. 1 SEAT 3 POINT TYPE BELT ASSEMBLY


    1. A01CCHS

      Install the rear No. 1 seat 3 point type belt assembly with the nut.

      42 N*m 428 kgf*cm 31 ft.*lbf
    2. A01CFJTE02

      Insert a pin punch into the zero point calibration hole of the reclining sensor.

      Table 2. Text in Illustration
      *1 Zero Point Calibration Hole

    3. With the pin punch inserted, install the reclining sensor with the 3 nuts.

      4.5 N*m 46 kgf*cm 40 in.*lbf

    4. Remove the pin punch.

  28. Click here

    INSTALL NO. 2 REAR SEAT SHOULDER BELT HOLE COVER


    1. A01CDCO

      Engage the 4 claws to install the No. 2 rear seat shoulder belt hole cover.

  29. Click here

    INSTALL REAR NO. 1 SEAT PROTECTOR


    1. A01CBQ4

      Engage the 4 guides.

    2. Install the rear No. 1 seat protector with the 3 clips.

  30. Click here

    INSTALL REAR NO. 1 SEATBACK COVER SUB-ASSEMBLY


    1. A01CDRC

      Using hog ring pliers, install the rear No. 1 seatback cover sub-assembly with new 11 hog rings.

      Note:

      • Be careful not to damage the cover.

      • Be sure to securely install the hog rings as shown in the illustration while preventing wrinkles from forming on the rear No. 1 seatback cover sub-assembly.

  31. Click here

    INSTALL REAR NO. 1 SEATBACK COVER WITH PAD


    1. Temporarily install the rear No. 1 seatback cover with pad to the rear No. 1 seatback frame sub-assembly.

    2. A01CC2G

      Engage the 4 claws to install the 2 rear seat headrest supports.

    3. A01CGF7

      Engage the 3 claws to connect the No. 2 seatback climate control duct.

    4. A01CFCGE03

      Close the 2 fasteners.

      Table 3. Text in Illustration
      *1 Fastener

    5. Using hog ring pliers, install the rear No. 1 seatback cover with pad with 3 new hog rings.

      Note:

      • Be careful not to damage the cover.

      • Be sure to securely install the hog rings as shown in the illustration while preventing wrinkles from forming on the rear No. 1 seatback cover with pad.

  32. Click here

    INSTALL REAR SEAT LOCK CONTROL LEVER SUB-ASSEMBLY


    1. A01CDJF

      Connect the 2 cable clamps.

    2. Install the rear seat lock control lever sub-assembly with the 2 screws.

  33. Click here

    INSTALL SEAT STAND FRAME CAP


    1. A01CEXX

      Engage the 2 claws to install the seat stand frame cap.

  34. Click here

    INSTALL REAR SEAT SHOULDER BELT COVER


    1. A01CCKP

      Install the rear seat shoulder belt cover with the 2 screws.

  35. Click here

    INSTALL REAR SHOULDER BELT ANCHOR COVER


    1. A01CCGV

      Engage the 6 claws to install the rear shoulder belt anchor cover.

  36. Click here

    INSTALL FRONT SHOULDER BELT ANCHOR COVER


    1. A01CFKZ

      Engage the guide.

    2. Engage the 2 claws to install the front shoulder belt anchor cover.

  37. Click here

    INSTALL RECLINING ADJUST LOWER INNER ARM SUB-ASSEMBLY


    1. A01CCG0

      Install the reclining adjust lower inner arm sub-assembly with the 4 bolts.

      22 N*m 224 kgf*cm 16 ft.*lbf

    2. Engage the 3 clamps to connect the seat wire.

    3. Connect the connector.

  38. Click here

    INSTALL NO. 1 REAR SEAT FOOTREST COVER


    1. A01CCOW

      Engage the 2 guides.

    2. Install the No. 1 rear seat footrest cover with the 2 screws.

  39. Click here

    INSTALL REAR SEAT LEG REST COVER


    1. A01CEVQ

      Install the rear seat leg rest cover with the 4 screws.

  40. Click here

    INSTALL REAR NO. 1 SEAT CUSHION COVER SUB-ASSEMBLY


    1. A01CEQLE04

      Using hog ring pliers, temporarily install the rear No. 1 seat cushion cover sub-assembly with 14 new hog rings.

      Table 4. Text in Illustration
      *1 Fastener
      Note:

      • Be careful not to damage the cover.

      • Be sure to securely install the hog rings as shown in the illustration while preventing wrinkles from forming on the rear No. 1 seat cushion cover sub-assembly.

    2. Engage the 2 fasteners.

    3. A01CB3L

      Using hog ring pliers, install the rear No. 1 seat cushion cover sub-assembly with 3 new hog rings.

      Note:

      • Be careful not to damage the cover.

      • Be sure to securely install the hog rings as shown in the illustration while preventing wrinkles from forming on the rear No. 1 seat cushion cover sub-assembly.

  41. Click here

    INSTALL REAR NO. 1 SEAT CUSHION COVER WITH PAD


    1. A01CEU7

      Engage the hook.

    2. A01CGD3

      Engage the 4 claws to connect the seat cushion climate control duct.

    3. A01CDMS

      Engage the 9 hooks.

    4. A01CER1

      Engage the 3 hooks to install the rear No. 1 seat cushion cover with pad.

  42. Click here

    INSTALL NO. 6 REAR SEAT LEG SIDE COVER


    1. A01CCAI

      Engage the claw.

    2. Install the No. 6 rear seat leg side cover with the screw.

  43. Click here

    INSTALL NO. 5 REAR SEAT LEG SIDE COVER


    1. A01CE5S

      Engage the claw.

    2. Install the No. 5 rear seat leg side cover with the screw.

  44. Click here

    INSTALL LOWER REAR SEAT LEG COVER


    1. A01CEJB

      Engage the 4 claws.

    2. Install the lower rear seat leg cover with the 2 screws.

    3. Engage the clamp.

  45. Click here

    INSTALL NO. 3 REAR SEAT LEG SIDE COVER


    1. A01CC94

      Engage the 2 claws and guide to install the No. 3 rear seat leg side cover.

  46. Click here

    INSTALL NO. 2 REAR SEAT LEG SIDE COVER


    1. A01CG3A

      Engage the 2 claws and guide to install the No. 2 rear seat leg side cover.

  47. Click here

    INSTALL NO. 3 RECLINING ADJUSTER INSIDE COVER


    1. A01CBV8

      Engage the guide.

    2. Install the No. 3 reclining adjuster inside cover with the screw.

  48. Click here

    INSTALL REAR SEAT ARMREST FRAME SUB-ASSEMBLY


    1. A01CG9QE01

      Engage the clip and guide.

      Table 5. Text in Illustration
      *a Bolt <A>
      *b Bolt <B>
      *c Nut <C>

    2. Install the rear seat armrest frame sub-assembly with the 5 bolts and 2 nuts.

      Bolt <A>
      14 N*m 143 kgf*cm 10 ft.*lbf
      Bolt <B>
      14 N*m 143 kgf*cm 10 ft.*lbf
      Nut <C>
      14 N*m 143 kgf*cm 10 ft.*lbf
  49. Click here

    INSTALL CUP HOLDER ASSEMBLY


    1. A01CEL9

      Install the cup holder assembly to the No. 1 rear seat cover bezel with the 3 screws.

  50. Click here

    INSTALL REAR POWER SEAT SWITCH


    1. A01CDH7

      Engage the 4 claws as shown in the illustration.

    2. Engage the wire harness clamp as shown in the illustration.

    3. Close the rear lower armrest base sub-assembly.

    4. A01CG4S

      Install the power seat switch with the 4 screws.

    5. A01CEWP

      Engage the 5 guides.

    6. A01CCRR

      Install the rear power seat switch with rear lower armrest base sub-assembly with the 3 screws.

  51. Click here

    INSTALL REAR POWER SEAT SWITCH WITH CUP HOLDER ASSEMBLY


    1. A01CEIG

      Install the rear power seat switch with cup holder assembly with the 3 bolts and 2 screws.

    2. Connect the connector and engage the 2 clamps.

  52. Click here

    INSTALL REAR SEAT ARMREST ASSEMBLY


    1. A01CB68

      Engage the guide.

    2. Install the rear seat armrest assembly with the 2 bolts.

      4.5 N*m 46 kgf*cm 40 in.*lbf
  53. Click here

    INSTALL REAR NO. 1 SEAT INNER BELT ASSEMBLY


    1. A01CFQWE01

      Install the rear No. 1 seat inner belt assembly with the bolt and washer.

      Table 6. Text in Illustration
      *1 Protruding Part
      42 N*m 428 kgf*cm 31 ft.*lbf
      Note:

      Do not allow the anchor part of the rear No. 1 seat inner belt assembly to overlap the protruding parts of the floor panel.

  54. Click here

    INSTALL REAR SEAT CUSHION MOULDING


    1. A01CGEN

      Engage the 2 guides.

    2. Engage the 5 claws.

    3. Engage the 4 clips.

    4. Install the rear seat cushion moulding with the 2 bolts.

  55. Click here

    INSTALL NO. 4 SEAT ADJUSTER COVER CAP


    1. A01CBID

      Engage the guide and claw to install the No. 4 seat adjuster cover cap.

  56. Click here

    INSTALL NO. 3 SEAT ADJUSTER COVER CAP


    1. A01CDF6

      Engage the guide and claw to install the No. 3 seat adjuster cover cap.

  57. Click here

    INSTALL SEAT ADJUSTER COVER CAP LH


    1. A01CC31

      Engage the 4 guides.

    2. Engage the 6 claws to install the seat adjuster cover cap LH.

  58. Click here

    INSTALL NO. 1 SEAT SIDE ADJUSTER COVER CAP (for RH Side)


    1. A01CFWB

      Engage the 2 claws to install the 2 No. 1 seat side adjuster cover caps.

  59. Click here

    INSTALL REAR SEAT SIDE TABLE (for RH Side)


    1. A01CB31

      Install the rear seat side table with the 2 nuts and 2 bolts.

    2. A01CFTC

      Engage the hook to store the table.

    3. A01CG3R

      Secure the rear seat side table clip with the screw.

  60. Click here

    INSTALL REAR SEAT SIDE TABLE BOARD (for RH Side)


    1. A01CDUH

      Engage the 6 clips to install the rear seat side table board.

  61. Click here

    INSTALL NO. 2 SEAT SIDE ADJUSTER COVER CAP (for RH Side)


    1. A01CEPE

      Engage the 2 claws and 2 guides to install the No. 2 seat side adjuster cover cap.

  62. Click here

    INSTALL REAR SEAT SIDE TABLE COVER (for RH Side)


    1. A01CGAW

      Engage the guide and claw to install the rear seat side table cover.

  63. Click here

    INSTALL RECLINING ADJUSTER INSIDE COVER RH


    1. A01CGEF

      Engage the 4 claws to install the reclining adjuster inside cover RH to the rear seat armrest frame sub-assembly RH.

  64. Click here

    INSTALL REAR NO. 1 SEAT ARMREST ASSEMBLY RH


    1. A01CEVG

      Install the rear No. 1 seat armrest assembly RH with the 4 bolts.

      4.5 N*m 46 kgf*cm 40 in.*lbf
  65. Click here

    INSTALL REAR NO. 1 SEAT ARMREST ASSEMBLY RH WITH FRAME AND COVER


    1. A01CF5N

      Install the rear No. 1 seat armrest assembly RH with frame and cover with the 4 nuts.

      14 N*m 143 kgf*cm 10 ft.*lbf
  66. Click here

    CONNECT NO. 1 SEAT 3 POINT TYPE BELT ASSEMBLY


    1. A01CF8NE02

      Connect the rear No. 1 seat 3 point type belt assembly with the bolt.

      Table 7. Text in Illustration
      *1 Protruding Part
      42 N*m 428 kgf*cm 31 ft.*lbf
      Note:

      Do not allow the anchor part of the rear No. 1 seat 3 point type belt assembly to overlap the protruding parts of the cushion frame.

  67. Click here

    INSTALL NO. 1 SEAT ADJUSTER COVER CAP


    1. A01CE2N

      Install the No. 1 seat adjuster cover cap with the 3 screws.

  68. Click here

    INSTALL RECLINING ADJUSTER COVER RH


    1. Connect the cable of the rear seat lock control lever sub-assembly.

    2. A01CBLHE01

      Slide the reclining adjuster cover RH onto the seat in the direction indicated by the arrow (1) in the illustration.

    3. Slide the reclining adjuster cover RH in the direction indicated by the arrow (2) in the illustration to engage the 2 guides.

    4. Engage the 3 claws and 3 clips.

    5. Install the 4 screws.

    6. Install the reclining adjuster cover RH with the 2 bolts.

  69. Click here

    INSTALL NO. 1 SEAT ADJUSTER COVER CAP


    1. A01CC13

      Engage the guide and claw to install the No. 1 seat adjuster cover cap.

  70. Click here

    INSTALL NO. 2 SEAT ADJUSTER COVER CAP


    1. A01CD2X

      Engage the guide and claw to install the No. 2 seat adjuster cover cap.

  71. Click here

    INSTALL NO. 3 RECLINING ADJUSTER INSIDE COVER RH


    1. A01CAMP

      Engage the 3 claws and 2 clips to install the No. 3 reclining adjuster inside cover RH.

  72. Click here

    INSTALL SEAT ADJUSTER COVER CAP RH


    1. A01CDZ2

      Engage the 4 guides and 6 claws to install the seat adjuster cover cap RH.

  73. Click here

    INSTALL REAR SEAT CUSHION


    1. A01CFJA

      Install the rear seat cushion with the screw.

  74. Click here

    INSTALL NO. 1 RECLINING ADJUSTER RELEASE HANDLE


    1. A01CB26

      Engage the claw to install the No. 1 reclining adjuster release handle.