Click here

FRONT SEAT ASSEMBLY (for Passenger Side Power Seat) REASSEMBLY

Click here
Click here Click here
  1. Click here

    INSTALL ACTIVE HEADREST LOWER UNIT


    1. A01CCLM

      Install the active headrest lower unit with the 2 nuts.

      5.0 N*m 51 kgf*cm 44 in.*lbf

    2. Install the new clamp.

  2. Click here

    INSTALL ACTIVE HEADREST UPPER UNIT


    1. A01CCL6E01

      Install the active headrest upper unit with the 4 nuts <B>.

      14 N*m 143 kgf*cm 10 ft.*lbf

    2. Install the active headrest lower unit cable with the nut <A>.

      5.0 N*m 51 kgf*cm 44 in.*lbf
  3. Click here

    INSTALL FRONT SEAT SIDE AIRBAG ASSEMBLY

    CAUTION:

    • The nuts must not be reused.

    • Make sure that the front seat frame with adjuster assembly is not deformed. If it is, replace it with a new one.


    1. A01CCL2

      Install the front seat side airbag assembly with 2 new nuts.

      5.5 N*m 56 kgf*cm 49 in.*lbf
    2. A01CEUJ

      Engage the 3 clamps.

    3. A01CFR5E01

      Engage the claw and 5 clamps to connect the wire harness.

    4. Connect the connector.

  4. Click here

    INSTALL FRONT SEAT WIRE


    1. Engage each clamp.

    2. Engage the 2 claws.

    3. A01CBI4

      Connect each connector and install the front seat wire.

  5. Click here

    INSTALL NO. 1 SEAT WIRE


    1. A01CFVM

      Engage the clamp.

    2. Connect the connector and install the No. 1 seat wire.

  6. Click here

    INSTALL RECLINING ADJUSTER INSIDE COVER LH


    1. A01CF1TE01

      Engage the clamp and guide.

    2. Install the reclining adjuster inside cover LH with the 2 screws.

  7. Click here

    INSTALL RECLINING ADJUSTER INSIDE COVER RH


    1. A01CAVQE01

      Engage the clamp and guide.

    2. Install the reclining adjuster inside cover RH with the 2 screws.

  8. Click here

    INSTALL NO. 1 RECLINING ADJUSTER INSIDE COVER LH


    1. A01CAV1

      Engage the guide.

    2. Install the No. 1 reclining adjuster inside cover LH with the screw.

  9. Click here

    INSTALL NO. 1 RECLINING ADJUSTER INSIDE COVER RH


    1. A01CCJV

      Engage the guide.

    2. Install the No. 1 reclining adjuster inside cover RH with the screw.

  10. Click here

    INSTALL NO. 1 FRONT SEAT FOOTREST COVER


    1. A01CEGV

      Install the No. 1 front seat footrest cover with the 2 clips.

  11. Click here

    INSTALL SEAT COVER HOOK


    1. A01CECU

      Install the 2 seat cover hooks.

  12. Click here

    INSTALL RECLINING ADJUSTER ARM ASSEMBLY


    1. A01CD17

      Install the reclining adjuster arm assembly with the 4 bolts.

      32 N*m 326 kgf*cm 24 ft.*lbf
    2. A01CASH

      Engage the 2 clamps.

    3. Connect the connector.

  13. Click here

    INSTALL SEPARATE TYPE FRONT SEATBACK COVER


    1. A01CBQ1

      Using hog ring pliers, install the separate type front seatback cover to the separate type front seatback pad with 11 new hog rings.

      Note:

      • Be careful not to damage the cover.

      • When installing the hog rings, avoid wrinkling the cover.

  14. Click here

    INSTALL SEPARATE TYPE FRONT SEATBACK COVER WITH PAD


    1. Temporarily install the separate type front seatback cover with pad.

    2. Connect the connector to the power seat switch assembly.

    3. A01CFEG

      Engage the 2 claws to install the power seat switch assembly.

    4. A01CEI0

      Engage the 4 claws to install the 2 front seat headrest supports.

    5. A01CFGR

      Install the nut.

      5.5 N*m 56 kgf*cm 49 in.*lbf
    6. A01CDX5

      Engage the 12 hooks.

    7. A01CD2H

      for Leather Seat:


      1. Engage the 2 clamps.

      2. Connect the connector.

    8. A01CB6O

      Using hog ring pliers, install the separate type front seatback cover with pad with 3 new hog rings.

      Note:

      • Be careful not to damage the cover.

      • When installing the hog rings, avoid wrinkling the cover.

    9. A01CC8R

      Using hog ring pliers, install the separate type front seatback cover with pad with 2 new hog rings.

      Note:

      • Be careful not to damage the cover.

      • When installing the hog rings, avoid wrinkling the cover.

  15. Click here

    INSTALL FRONT SEAT ARMREST ASSEMBLY


    1. A01CC57

      Install the front seat armrest assembly with the bolt.

      37 N*m 377 kgf*cm 27 ft.*lbf
  16. Click here

    INSTALL SEAT ARMREST COVER


    1. A01CALV

      Engage the 3 claws to install the seat armrest cover.

  17. Click here

    INSTALL FRONT SEATBACK POCKET CLIP


    1. A01CAPY

      Install the 2 front seatback pocket clips to the front seatback board sub-assembly.

  18. Click here

    INSTALL FRONT SEATBACK BOARD SUB-ASSEMBLY


    1. A01CFHK

      Engage the 2 guides.

    2. Install the front seatback board sub-assembly with the 2 screws.

  19. Click here

    INSTALL LOWER NO. 2 FRONT SEATBACK LOCK BEZEL


    1. A01CCUL

      Engage the 4 claws.

    2. Install the lower No. 2 front seatback lock bezel with the 2 screws.

  20. Click here

    INSTALL LOWER NO. 1 FRONT SEATBACK LOCK BEZEL


    1. A01CGHW

      Engage the 4 claws.

    2. Install the lower No. 1 front seatback lock bezel with the 2 screws.

  21. Click here

    INSTALL FRONT SEATBACK LOCK HANDLE


    1. A01CFY4

      Install the front seatback lock handle to the front seatback edge protector.

  22. Click here

    INSTALL RECLINING ADJUSTER RELEASE HANDLE LH


    1. A01CE40

      Install the reclining adjuster release handle LH.

  23. Click here

    INSTALL RECLINING ADJUSTER RELEASE HANDLE LH


    1. A01CATU

      Install the reclining adjuster release handle LH.

  24. Click here

    INSTALL FRONT SEATBACK LOCK ASSEMBLY


    1. A01CBT9

      Install the front seatback lock assembly with the 2 screws.

    2. A01CF7N

      Install the spring.

  25. Click here

    INSTALL LOWER FRONT SEATBACK COVER SUB-ASSEMBLY


    1. A01CCUA

      Using hog ring pliers, install the lower front seatback cover sub-assembly to the lower front seatback frame assembly with 9 new hog rings.

      Note:

      • Be careful not to damage the cover.

      • When installing the hog rings, avoid wrinkling the cover.

  26. Click here

    INSTALL FRONT SEATBACK EDGE PROTECTOR


    1. A01CAY7

      Engage the 2 claws while pulling the lever as shown in the illustration and temporarily install the front seatback edge protector.

    2. A01CBF9

      Install the front seatback edge protector with the 3 screws.

  27. Click here

    INSTALL SEAT STAND FRAME CAP


    1. A01CB0W

      Engage the 3 guides and 3 claws to install the 3 seat stand frame caps.

  28. Click here

    INSTALL LOWER NO. 3 FRONT SEATBACK LOCK BEZEL


    1. A01CAV5

      Install the lower No. 3 front seatback lock bezel.

      Tip:

      Use the same procedure for the LH side and RH side.

  29. Click here

    INSTALL FOOTREST ASSEMBLY


    1. A01CDW6

      Install the footrest assembly with the 4 bolts.

      32 N*m 326 kgf*cm 24 ft.*lbf
  30. Click here

    INSTALL CONNECTOR HOLDER


    1. A01CCFN

      Install the connector holder to the occupant detection sensor connector.

  31. Click here

    INSTALL SEPARATE TYPE FRONT SEAT CUSHION COVER


    1. A01CEG0

      Using hog ring pliers, install the separate type front seat cushion cover to the separate type front seat cushion pad with 18 new hog rings.

      Note:

      • Be careful not to damage the cover.

      • When installing the hog rings, avoid wrinkling the cover.

    2. A01CF16E01

      Engage the 2 fasteners.

  32. Click here

    INSTALL SEPARATE TYPE FRONT SEAT CUSHION COVER WITH PAD


    1. A01CDOI

      Engage the 8 hooks and install the separate type front seat cushion cover with pad.

    2. Engage the 4 clips.

    3. Install the 2 clips.

    4. A01CC9TE01

      Engage the 4 hooks.

    5. Engage the clamp.

    6. Connect the occupant detection sensor connector.

    7. for Leather Seat:


      1. Connect the connector.

  33. Click here

    INSTALL FRONT SEAT CUSHION HINGE COVER LH


    1. A01CBCK

      Install the front seat cushion hinge cover LH with the screw.

  34. Click here

    INSTALL FRONT SEAT COVER (for LH Side)


    1. A01CBM2

      Engage the claw and guide to install the front seat cover.

  35. Click here

    INSTALL FRONT SEAT CUSHION HINGE COVER RH


    1. A01CC9M

      Install the front seat cushion hinge cover RH with the screw.

  36. Click here

    INSTALL FRONT SEAT COVER (for RH Side)


    1. A01CEVU

      Engage the claw and guide to install the front seat cover.

  37. Click here

    INSTALL FRONT SEAT PLATE SUB-ASSEMBLY LH


    1. A01CEO3

      Install the front seat plate sub-assembly LH with the screw as shown in the illustration.

  38. Click here

    INSTALL FRONT SEAT PLATE SUB-ASSEMBLY RH


    1. A01CBD2

      Install the front seat plate sub-assembly RH with the screw as shown in the illustration.

  39. Click here

    INSTALL NO. 2 FRONT SEAT FOOTREST COVER


    1. A01CC16

      Engage the 2 guides.

    2. A01CD8O

      Engage the clamp.

    3. Install the No. 2 front seat footrest cover with the 2 screws.

  40. Click here

    INSTALL NO. 1 FRONT SEAT INNER CUSHION SHIELD RH


    1. A01CEWN

      Engage the 2 clips.

    2. Install the No. 1 front seat inner cushion shield RH with the screw.

  41. Click here

    INSTALL NO. 1 FRONT SEAT INNER CUSHION SHIELD LH


    1. A01CBO8

      Engage the 2 clips.

    2. Install the No. 1 front seat inner cushion shield LH with the screw.

  42. Click here

    INSTALL FRONT SEAT INNER BELT ASSEMBLY


    1. A01CF4GE01

      Install the front seat inner belt assembly with the nut.

      42 N*m 428 kgf*cm 31 ft.*lbf
      Note:

      Do not allow the anchor part of the front seat inner belt assembly to overlap the protruding parts of the front seat adjuster.

    2. A01CANQ

      Engage each clamp.

    3. Connect each connector.

  43. Click here

    INSTALL FRONT SEAT INNER CUSHION SHIELD


    1. A01CCTQ

      Engage the 7 claws, clip and 2 guides.

    2. Install the front seat inner cushion shield and No. 2 reclining adjuster inside cover RH with the 2 screws.

  44. Click here

    INSTALL FRONT POWER SEAT SWITCH


    1. A01CF2W

      Connect the connector.

    2. Install the front power seat switch with the 3 screws.

  45. Click here

    INSTALL FRONT POWER SEAT SWITCH ASSEMBLY


    1. A01CBSI

      Install the front power seat switch assembly to the front seat cushion shield with the 2 screws.

  46. Click here

    INSTALL FRONT SEAT CUSHION SHIELD


    1. Connect the connector.

    2. Engage the 2 clamps.

    3. A01CFUD

      Engage the 8 claws and 2 guides.

    4. Install the front seat cushion shield and No. 2 reclining adjuster inside cover LH with the 3 screws.

    5. A01CFNA

      Engage the 2 hooks.

  47. Click here

    INSTALL SLIDE POWER SEAT SWITCH KNOB


    1. A01CBRW

      Install the slide power seat switch knob.

  48. Click here

    INSTALL RECLINING POWER SEAT SWITCH KNOB


    1. A01CFDZ

      Install the reclining power seat switch knob.

  49. Click here

    INSTALL LOWER FRONT SEAT LEG COVER


    1. A01CCGX

      Install the lower front seat leg cover.

  50. Click here

    INSTALL FRONT SEAT LEG ASSEMBLY


    1. A01CCEX

      Install the front seat leg assembly with the 5 nuts.

      20 N*m 204 kgf*cm 15 ft.*lbf

    2. Engage the 2 clamps.

    3. Connect the 2 connectors.

  51. Click here

    INSTALL SEAT ADJUSTER COVER CAP


    1. A01CGHG

      Install the 2 seat adjuster cover caps.