GLOVE BOX LIGHT REMOVAL


  1. REMOVE SHIFT LEVER KNOB SUB-ASSEMBLY


    1. A01CD4S

      Turn the shift lever knob counterclockwise and remove the shift lever knob sub-assembly.

  2. REMOVE CENTER INSTRUMENT CLUSTER FINISH PANEL SUB-ASSEMBLY


    1. A01CG21E02

      Apply protective tape to the area shown in the illustration.

    2. A01CEQF

      Move the shift lever to N.

    3. Disengage the 3 claws as shown in the illustration.

      Note

      Make sure to disengage the lower claws first. The center instrument cluster finish panel sub-assembly may be damaged if the upper claws are disengaged first.

    4. A01CCCC

      Disengage the 20 claws.

      Note

      Make sure to disengage the lower claws first. The center instrument cluster finish panel sub-assembly may be damaged if the upper claws are disengaged first.

    5. Disconnect the connector and remove the center instrument cluster finish panel sub-assembly.

  3. REMOVE INTERIOR ILLUMINATION LIGHT ASSEMBLY (for Center)


    1. A01CFNI

      Disconnect the connector.

    2. Disengage the guide and remove the interior illumination light assembly as shown in the illustration.

  4. REMOVE COWL SIDE TRIM BOARD RH (for RHD)


    1. A01CFL6

      Remove the clip.

    2. Disengage the clip, claw and 2 guides, and remove the cowl side trim board RH.

  5. REMOVE COWL SIDE TRIM BOARD LH (for LHD)


    1. A01CCIK

      Remove the clip(A).

    2. Disengage the clip, claw and 2 guides, and remove the cowl side trim board LH.

  6. REMOVE NO. 1 INSTRUMENT PANEL UNDER COVER SUB-ASSEMBLY (for RHD)


    1. A01CFFK

      Remove the 2 screws <B>.

    2. Disengage the 2 claws and 2 guides.

    3. A01CE9QE01

      Disengage the 2 claws and disconnect the DLC3.

    4. Disengage the clamp.

    5. Disconnect each connector and remove the No. 1 instrument panel under cover sub-assembly.

  7. REMOVE NO. 1 INSTRUMENT PANEL UNDER COVER SUB-ASSEMBLY (for LHD)


    1. A01CCYO

      Remove the 2 screws <B>.

    2. Disengage the 2 claws and guide.

    3. Disengage the clamp.

    4. Disconnect each connector and remove the No. 1 instrument panel under cover sub-assembly.

  8. REMOVE LOWER INSTRUMENT PANEL FINISH PANEL (for RHD)


    1. A01CC18

      Disengage the 3 claws and disconnect the hood lock control cable assembly.

    2. A01CC11

      Disengage the 3 claws and disconnect the fuel lid lock control cable assembly.

    3. A01CCKN

      Remove the 3 screws <B>.

    4. Disengage the 14 claws and the 3 guides, and remove the lower instrument panel finish panel as shown in the illustration.

      A01CCUJ

      Note


      • Make sure to follow the order shown in the illustration to avoid damage to the lower instrument panel finish panel.

      • While supporting the knee airbag, remove the lower instrument panel finish panel.

  9. REMOVE LOWER INSTRUMENT PANEL FINISH PANEL (for LHD)


    1. A01CF0E

      Disengage the 3 claws and disconnect the hood lock control cable assembly.

    2. A01CCXK

      Disengage the 3 claws and disconnect the fuel lid lock control cable assembly.

    3. A01CGDM

      Disconnect the fuel filler opening lid lock sub-assembly and remove the fuel lid lock open lever sub-assembly.

    4. A01CCWL

      Remove the 3 screws <B>.

    5. Disengage the 13 claws, clip and the 3 guides and remove the lower instrument panel finish panel as shown in the illustration.

      A01CECJ

      Note


      • Make sure to follow the order shown in the illustration to avoid damage to the lower instrument panel finish panel.

      • While supporting the knee airbag, remove the lower instrument panel finish panel.

  10. REMOVE CENTER FLOOR CARPET COVER RH (for RHD)


    1. A01CDKB

      Using a clip remover, remove the 2 clips.

    2. A01CFS0E01

      Disengage the 4 claws and remove the center floor carpet cover RH in the order shown in the illustration.

      Tech Tips

      Remove the center floor carpet cover RH while pushing on the instrument cluster finish panel.

  11. REMOVE CENTER FLOOR CARPET COVER RH (for LHD)


    1. A01CBO2

      Using a clip remover, remove the clip.

    2. A01CB02E01

      Disengage the 5 claws and remove the center floor carpet cover RH in the order shown in the illustration.

      Tech Tips

      Remove the center floor carpet cover RH while pushing on the instrument cluster finish panel.

  12. REMOVE CENTER FLOOR CARPET COVER LH


    1. A01CG2A

      Using a clip remover, remove the clip.

    2. A01CF5YE01

      Disengage the 4 claws and remove the center floor carpet cover LH in the order shown in the illustration.

      Tech Tips

      Remove the center floor carpet cover LH while pushing on the instrument cluster finish panel.

  13. REMOVE NO. 2 INSTRUMENT PANEL UNDER COVER SUB-ASSEMBLY


    1. Disengage the 4 claws and 2 guides.

      A01CFSFE01

    2. Disconnect the connector and remove the No. 2 instrument panel under cover sub-assembly.

  14. REMOVE GLOVE COMPARTMENT DOOR ASSEMBLY


    1. A01CC1ZE01

      Disengage the claw and release the glove compartment door stopper.

    2. Slightly bend stoppers (A) and (B) in the directions indicated by the arrows in the illustration and pull the glove compartment door assembly until the stoppers are released.

    3. A01CFV2E01

      Open the glove compartment door assembly to approximately 55° from its closed position. Pull it horizontally toward the rear of the vehicle to disengage the 2 hinges and remove the glove compartment door assembly.

      Note

      Pulling the glove compartment door assembly upward to remove it causes the hinges to deform. Be sure to pull out the glove compartment door assembly horizontally.

  15. REMOVE INSTRUMENT PANEL BOX ASSEMBLY


    1. A01CD8ZE01

      Slightly bend stoppers (A) and (B) in the directions indicated by the arrows in the illustration and pull the instrument panel box assembly until the stoppers are released.

    2. Remove the damper clip.

    3. A01CGCYE01

      Open the instrument panel box assembly to approximately 60° from its closed position. Pull it horizontally toward the rear of the vehicle to disengage the 2 hinges and remove the instrument panel box assembly.

      Note

      Pulling the instrument panel box assembly upward to remove it causes the hinges to deform. Be sure to pull out the instrument panel box horizontally.

  16. REMOVE INSTRUMENT CLUSTER FINISH PANEL ASSEMBLY


    1. A01CFL8

      Remove the bolt <C>.

    2. Disengage the 12 claws.

      Tech Tips

      First disengage the 6 claws for the right side and then pull the panel to the rear of the vehicle to disengage the 6 claws for the left side.

    3. A01CD3Y

      Disengage the 3 claws.

    4. Disconnect each connector and remove the instrument cluster finish panel assembly.

  17. REMOVE NO. 3 INSTRUMENT CLUSTER FINISH PANEL GARNISH


    1. A01CC1I

      Disengage the 16 claws and remove the No. 3 instrument cluster finish panel garnish.

      Note

      Disengage the bottom claws first.

  18. REMOVE NO. 1 INSTRUMENT PANEL BOX DOOR SUB-ASSEMBLY


    1. A01CD7CE01

      Using a screwdriver, disengage the 6 claws as shown in the illustration.

      Tech Tips

      Pull the door toward the rear of the vehicle while pushing down on the 4 claws at the corners.

      Note


      • When pushing down on the 4 claws, be careful not to damage them. These claws are difficult to disengage.

      • When removing the No. 1 instrument panel box door sub-assembly, make sure to close the lid to avoid damage.

    2. Disconnect the connector and remove the No. 1 instrument panel box door sub-assembly.

  19. REMOVE INTERIOR ILLUMINATION LIGHT ASSEMBLY (for Side)


    1. for RHD:


      1. A01CCSI

        Disengage the guide and remove the interior illumination light assembly as shown in the illustration.

    2. for LHD:


      1. A01CDAY

        Disengage the guide and remove the interior illumination light assembly as shown in the illustration.

  20. REMOVE GLOVE BOX LIGHT ASSEMBLY


    1. A01CAP9

      Disconnect the connector.

    2. Disengage the guide and remove the glove box light assembly as shown in the illustration.