Click here

NAVIGATION SYSTEM DTC CHECK / CLEAR

Click here
Click here Click here
Click here

  1. CHECK DTC (CHECK USING INTELLIGENT TESTER)


    1. Connect the intelligent tester to the DLC3.

    2. Turn the engine switch on (IG).

    3. Turn the intelligent tester on.

    4. Enter the following menus: Body / Navigation System / DTC.

    5. Check for DTCs, and then write them down.

    6. Check the details of the DTC(s) (Click here).

      Note:

      The navigation system outputs DTCs for the following systems. When DTCs other than those in Diagnostic Trouble Code Chart for the navigation system are output, refer to Diagnostic Trouble Code Chart for the relevant systems.

      System Proceed to
      Parking Assist Monitor System

      Click here
      Rear Seat Entertainment System*1

      Click here

      • *1: w/ Front Center Speaker

  2. CLEAR DTC (CLEAR USING INTELLIGENT TESTER)


    1. Connect the intelligent tester to the DLC3.

    2. Turn the engine switch on (IG).

    3. Turn the intelligent tester on.

    4. Enter the following menus: Body / Navigation System / DTC.

    5. Clear the DTCs.

  3. START DIAGNOSTIC MODE

    Tip:

    • Illustrations may differ from the actual vehicle screen depending on the device settings and options. Therefore, some detailed areas may not be shown exactly the same as on the actual vehicle screen.

    • After the engine switch is turned on (IG), check that the map is displayed before starting diagnostic mode. Otherwise, some items cannot be checked.


    1. Start the engine.

    2. A01CB25

      While pressing and holding the "INFO" switch, operate the light control switch: Off → Tail → Off → Tail → Off → Tail → Off.

    3. Diagnostic mode starts and the "Service Menu" screen will be displayed. Service inspection starts automatically and the result will be displayed.

  4. FAILURE DIAGNOSIS


    1. A01CCT7

      The "Failure Diagnosis" screen will be displayed by pressing the "Failure Diagnosis" switch on the "Service Menu" screen.

  5. SYSTEM CHECK (w/ Front Center Speaker)


    1. A01CAZ8

      The "System Check Mode" screen will be displayed by pressing the "System Check" switch on the "Failure Diagnosis" screen.

  6. SYSTEM CHECK (w/o Front Center Speaker)


    1. A01CELL

      The "System Check Mode" screen will be displayed by pressing the "System Check" switch on the "Failure Diagnosis" screen.

  7. CHECK DTC (CHECK USING SYSTEM CHECK MODE SCREEN) (w/ Front Center Speaker)


    1. A01CFNTE01

      System check mode screen description

      Table 1. Screen Description
      Display Content
      *a: Node position number for devices connected to the MOST network. MOST network node position numbers are provided for devices connected to the MOST network.
      *b: Device Name List No. 1

      • Device Name List No. 1 displays some of the devices that make up the navigation system.

      • The names of the components from Device Name List No. 1 are shown in the following table.
      *c: Check Result

      • Result codes for all devices are displayed.

      • When "MOST" is displayed for the result, press "MOST" on the multi-display assembly to display the "MOST Line Check" screen.
      *d: Memory Clear

      • Present and history DTCs and registered connected device names are cleared.

      • Press the "Memory CLR" switch for 3 seconds.
      *e: Recheck

      • A system check will be performed again after the memory is cleared.

      • The "Recheck" switch will dim during a system check.
      *f: Device Name List No. 2

      • Device Name List No. 2 displays some of the devices that make up the navigation system.

      • The names of the components from Device Name List No. 2 are shown in the following table.
      Table 2. *a: Device Name List No. 1 Description
      Name Component Connection Method
      AVN Navigation receiver assembly -
      AMP Stereo component amplifier assembly Communication line for MOST network
      REAR Television display assembly Communication line for MOST network
      Table 3. *b: Check Result Description
      Result Meaning Action
      OK The device does not respond with a DTC. -
      MOST MOST communication error Perform "MOST Line Check" to check the connection of each device on the MOST network.
      DETAIL The device responds with a DTC. Look up the DTC in "Unit Check Mode".
      NCON The device was previously present, but does not respond in diagnostic mode.

      - Check power supply wire harness of the device.

      - Check the AVC-LAN of the device.
      NRES The device responds in diagnostic mode, but gives no DTC information.

      - Check power supply wire harness of the device.

      - Check the AVC-LAN of the device.
      Table 4. *e: Device Name List No. 2 Description
      Name Component Connection Method
      VTR/FR Video (video adapter) terminal Vehicle wire harness
    2. A01CE5LE01

      Unit check mode screen description

      Table 5. Screen Description
      Display Content
      *a: Device name Target device
      *b: History DTC Diagnostic memory results and stored DTCs are displayed.
      *c: Current DTC DTCs output in the service check are displayed.
      *d: DTC DTC (Diagnostic Trouble Code)
      *e: Timestamp The time and date of history DTCs are displayed. (The year is displayed in 2-digit format.)
      *f: Diagnosis clear switch Pushing this switch for 3 seconds clears the diagnostic memory data of the target device. (Both response to diagnostic system check result and the displayed data are cleared.)
      Tip:

      • This screen is updated once per second.

      • A maximum of 6 DTCs can be displayed for history and present DTCs.

    3. A01CFCYE01

      MOST line check screen description

      Tip:

      • The inspection will be performed at the time the screen changes from "System Check Mode" to "MOST Line Check".

      • The master unit checks the connection of each device on the MOST network.

      Table 6. Screen Description
      Display Content
      *a: Node position number for devices connected to the MOST network. MOST node position numbers are provided for devices connected to the MOST network.
      *b: Device Name List

      • Device Name List displays some of the devices that make up the navigation system.

      • The names of the components from Device Name List are shown in the following table.
      *c: Check Result The master unit displays the check result on the screen based on the response information from each slave unit.
      Table 7. *b: Device Name List
      Name Component
      AVN Navigation receiver assembly
      AMP Stereo component amplifier assembly
      REAR Television display assembly
      Table 8. *c: Check Result
      Result Meaning
      OK There was a response for the connection check during the MOST line check.
      NCON There was no response for the connection check during the MOST line check.
      Tip:

      • The device name and result will not be displayed if there is no system registration record and no response for the connection check during the MOST line check even if the device is connected to the MOST network.

    4. A01CC3V

      Read the system check result.


      1. If the check result is "DETAIL", touch the displayed check result to view the results on the "Unit Check Mode" screen and record them.

        Note:

        A maximum of 6 DTCs can be displayed for history and present DTCs on the "Unit check mode" screen. Therefore, when 6 DTCs are displayed, troubleshoot those DTCs first and then check the "Unit check mode" screen again to see if any other DTCs are displayed.

        Tip:

        • When all results are "OK", this means that no DTCs are present.

        • When "MOST" is displayed for the result, select the "MOST" switch to display the "MOST Line Check" and check the MOST network.

        • Changing to the "MOST Line Check" screen is possible only when the MOST network is malfunctioning and "MOST" is displayed for the result.

        • If the MOST network had a malfunction in the past, the DTCs will be displayed in the Memory column.

        • When proceeding to view the results of another device, select the "Back" switch to return to the "System Check Mode" screen. Repeat the above step to view the results of other devices.

      2. Check the details of the DTC(s) (Click here).

        Note:

        The navigation system outputs DTCs for the following systems. When DTCs other than those in Diagnostic Trouble Code Chart for the navigation system are output, refer to Diagnostic Trouble Code Chart for the relevant systems.

        System Proceed to
        Parking Assist Monitor System

        Click here
        Rear Seat Entertainment System

        Click here

  8. CHECK DTC (CHECK USING SYSTEM CHECK MODE SCREEN) (w/o Front Center Speaker)

    Tip:

    When "NCON" is displayed for all devices connected using the AVC-LAN, or when all device names are not displayed, check if there is a short circuit in the AVC-LAN or devices connected to the AVC-LAN. Repair or replace parts as necessary (Click here).


    1. A01CFJNE01

      System check mode screen description

      Table 9. Screen Description
      Display Content
      *a: Device Name List No. 1

      • Device Name List No. 1 displays some of the devices that make up the navigation system.

      • The names of the components from Device Name List No. 1 are shown in the following table.
      *b: Check Result Result codes for all devices are displayed.
      *c: Memory Clear

      • Present and history DTCs and registered connected device names are cleared.

      • Press the "Memory CLR" switch for 3 seconds.
      *d: Recheck

      • A system check will be performed again after the memory is cleared.

      • The "Recheck" switch will dim during a system check.
      *e: Device Name List No. 2

      • Device Name List No. 2 displays some of the devices that make up the navigation system.

      • The names of the components from Device Name List No. 2 are shown in the following table.
      Table 10. *a: Device Name List No. 1 Description
      Name Component Connection Method
      AVN Navigation receiver assembly -
      Rr-TV Television display assembly Communication line for AVC-LAN
      Table 11. *b: Check Result Description
      Result Meaning Action
      OK The device does not respond with a DTC. -
      DETAIL The device responds with a DTC. Look up the DTC in "Unit Check Mode".
      NCON The device was previously present, but does not respond in diagnostic mode.

      - Check power supply wire harness of the device.

      - Check the AVC-LAN of the device.
      NRES The device responds in diagnostic mode, but gives no DTC information.

      - Check power supply wire harness of the device.

      - Check the AVC-LAN of the device.
      Table 12. *e: Device Name List No. 2 Description
      Name Component Connection Method
      VTR/RR Video (video adapter) terminal Vehicle wire harness
    2. A01CE5LE01

      Unit check mode screen description

      Table 13. Screen Description
      Display Content
      *a: Device name Target device
      *b: History DTC Diagnostic memory results and stored DTCs are displayed.
      *c: Current DTC DTCs output in the service check are displayed.
      *d: DTC DTC (Diagnostic Trouble Code)
      *e: Timestamp The time and date of history DTCs are displayed. (The year is displayed in 2-digit format.)
      *f: Diagnosis clear switch Pushing this switch for 3 seconds clears the diagnostic memory data of the target device. (Both response to diagnostic system check result and the displayed data are cleared.)
      Tip:

      • This screen is updated once per second.

      • A maximum of 6 DTCs can be displayed for history and present DTCs.

    3. A01CDV9
      A01CCMP

      Read the system check result.


      1. If the check result is "DETAIL", touch the displayed check result to view the results on the "Unit Check Mode" screen and record them.

        Note:

        A maximum of 6 DTCs can be displayed for history and present DTCs on the "Unit check mode" screen. Therefore, when 6 DTCs are displayed, troubleshoot those DTCs first and then check the "Unit check mode" screen again to see if any other DTCs are displayed.

        Tip:

        • When all results are "OK", this means that no DTCs are present.

        • When proceeding to view the results of another device, press the "Back" switch to return to the "System Check Mode" screen. Repeat the step above to view the results of other devices.

      2. Check the details of the DTC(s) (Click here).

        Note:

        The navigation system outputs DTCs for the following systems. When DTCs other than those in Diagnostic Trouble Code Chart for the navigation system are output, refer to Diagnostic Trouble Code Chart for the relevant systems.

        System Proceed to
        Parking Assist Monitor System

        Click here

  9. DTC CLEAR/RECHECK (CLEAR USING SYSTEM CHECK MODE SCREEN) (w/ Front Center Speaker)


    1. A01CC60

      Clear DTC


      1. Press the "Memory CLR" switch for 3 seconds.

      2. Confirm that the check results are cleared.

        Tip:

        • To clear the DTC for a specific device, clear the DTC using the "Unit Check Mode" screen.

        • When clearing a DTC using the "Unit Check Mode" screen, press the "Code CLR" switch for 3 seconds.

    2. A01CERF

      Recheck


      1. Press the "Recheck" switch.

      2. A01CETC

        Confirm that all diagnostic codes are "OK" when the check results are displayed. If a code other than "OK" is displayed, troubleshoot again.

        Tip:

        When a DTC was cleared using the "Unit Check Mode" screen, press the "Back" switch to return to the "System Check Mode" screen and perform this operation.

  10. DTC CLEAR/RECHECK (CLEAR USING SYSTEM CHECK MODE SCREEN) (w/o Front Center Speaker)


    1. A01CBOJ

      Clear DTCs


      1. Press the "Memory CLR" switch for 3 seconds.

      2. Confirm that the check results are cleared.

        Tip:

        • To clear the DTCs for a specific device, clear the DTCs using the "Unit Check Mode" screen.

        • When clearing the DTCs using the "Unit Check Mode" screen, press the "Code CLR" switch for 3 seconds.

    2. A01CG2E

      Recheck


      1. Press the "Recheck" switch.

      2. A01CCYP

        Confirm that all diagnostic codes are "OK" when the check results are displayed. If a code other than "OK" is displayed, troubleshoot again.

        Tip:

        When the DTCs are cleared using the "Unit Check Mode" screen, press the "Back" switch to return to the "System Check Mode" screen and perform this operation.

  11. FINISH DIAGNOSTIC MODE


    1. Turn the engine switch off.