REAR SEAT ENTERTAINMENT SYSTEM (w/ Front Center Speaker) HOW TO PROCEED WITH TROUBLESHOOTING

Tech Tips


  • Use the following procedure to troubleshoot the rear seat entertainment system.

  • *: Use the intelligent tester.


  1. VEHICLE BROUGHT TO WORKSHOP


    NEXT

  2. CUSTOMER PROBLEM ANALYSIS


    • When troubleshooting, confirm that the problem symptoms have been accurately identified. Preconceptions should be discarded in order to make an accurate judgment. To clearly understand what the problem symptoms are, it is extremely important to ask the customer about the problem and the conditions at the time the malfunction occurred.

    • Gather as much information as possible for reference. Past problems that seem unrelated may also help in some cases.

    • The following 5 items are important points in problem analysis:

      What Vehicle model, system name
      When Date, time, occurrence frequency
      Where Road conditions
      Under what conditions? Driving conditions, weather conditions
      How did it happen? Problem symptoms

    NEXT

  3. INSPECT BATTERY VOLTAGE


    1. Measure the battery voltage.

      Standard Voltage
      11 to 14 V

      If the voltage is below 11 V, recharge or replace the battery before proceeding to the next step.


      NEXT

  4. CHECK CABIN


    1. Check that condensation is not likely to occur in the cabin, and that the temperature is not high or extremely low in the cabin.

      OK
      Condensation is not likely being produced and the temperature is not high or extremely low.

      Tech Tips


      • A humid cabin and a rapid change in temperature may lead to condensation. Condensation in the cabin may cause a short circuit.

      • The audio and visual system may not operate normally when the temperature is -20°C (-4°F) or lower, or 65°C (149°F) or higher.


      NG

      SET CABIN TO APPROPRIATE TEMPERATURE
      OK

  5. CHECK FOR DTC*


    1. Refer to DTC Check / Clear Click here.

      Result
      Result Proceed to
      DTCs are output. A
      DTCs are not output. B

      Tech Tips

      If more information is needed, perform a recheck using the "System Check Mode" screen after rechecking for DTCs using the intelligent tester Click here.


      B

      Go to step 9
      A

  6. DTC CLEAR*


    1. Clear the DTCs and finish diagnostic mode.

      Tech Tips

      The current DTCs may not indicate actual malfunctions depending on the vehicle operating conditions.


      NEXT

  7. RECHECK FOR DTC*


    1. Recheck for DTCs.

      Result
      Result Proceed to
      DTCs are output. A
      DTCs are not output. B

      Tech Tips


      • Even if the malfunction symptom cannot be confirmed, check for DTCs. This is because the system stores history DTCs.

      • If more information is needed, perform a recheck using the "System Check Mode" screen after rechecking for DTCs using the intelligent tester Click here.

      • Check the DTCs and inspect the area the code indicates.


      B

      Go to step 9
      A

  8. DIAGNOSTIC TROUBLE CODE CHART


    1. Find the output code in the diagnostic trouble code chart Click here.


      NEXT

      Go to step 11

  9. PROBLEM SYMPTOMS TABLE


    1. Refer to Problem Symptoms Table Click here.

      Result
      Result Proceed to
      Fault is not listed in Problem Symptoms Table. A
      Fault is listed in Problem Symptoms Table. B

      Tech Tips

      If the symptom does not recur and no DTC is output, perform the symptom simulation method Click here.


      B

      Go to step 11
      A

  10. PERFORM TROUBLESHOOTING BASED ON MALFUNCTION SYMPTOM


    1. Refer to Terminals of ECU Click here.


      NEXT

  11. CHECK CIRCUIT


    1. Adjust, repair or replace as necessary.


      NEXT

  12. RECHECK FOR DTC*

    Tech Tips

    After clearing the DTCs, recheck for DTCs.


    NEXT

  13. PERFORM CONFIRMATION TEST


    NEXT
    END