AMPLIFIER ANTENNA REMOVAL


  1. REMOVE REAR NO. 2 SEAT ASSEMBLY

    Click here

  2. REMOVE BACK DOOR STRIKER COVER


    1. A01CDGVE02
      Text in Illustration
      *1 Protective Tape

      Using a screwdriver, disengage the 4 claws and 2 guides, and remove the back door striker cover.

      Tech Tips

      Tape the screwdriver tip before use.

  3. REMOVE BACK DOOR SCUFF PLATE


    1. A01CCY0

      Remove the 4 claws, 4 clips and 2 guides, and remove the back door scuff plate.

  4. REMOVE REAR DOOR SCUFF PLATE


    1. Captain type rear seat:


      1. A01CFIB

        Disengage the 9 claws, 9 clips and 2 guides, and remove the rear door scuff plate RH.

    2. Tip-up type rear seat:


      1. A01CGAPE02
        Text in Illustration
        *1 Protective Tape

        Apply protective tape to the bottom of the seat as shown in the illustration.

      2. A01CEQB

        Using the slide lever, slide the rear No. 1 seat to the rearmost position.

      3. Disengage the 4 clips, 5 claws and guide on the front side of the scuff plate as shown in the illustration.

        Note

        To prevent damage to the scuff plate, make sure not to use excessive force when disengaging the clips, claws and guide.

      4. A01CETW

        Using the reclining lever or foot-operated walk-in pedal, tip up the rear No. 1 seat and slide it to the foremost position.

      5. Disengage the 5 clips, 4 claws and guide on the rear side of the scuff plate as shown in the illustration, and remove the rear door scuff plate RH.

        Note

        To prevent damage to the scuff plate, make sure not to use excessive force when disengaging the clips, claws and guide.

  5. DISCONNECT NO. 1 SLIDE DOOR WEATHERSTRIP


    1. Disconnect the No. 1 slide door weatherstrip.

  6. REMOVE NO. 1 LUGGAGE COMPARTMENT TRIM HOOK


    1. A01CDVME01

      Turn the No. 1 luggage compartment trim hook clockwise approximately 90° and pull it out as shown in the illustration.

    2. A01CAW1

      Remove the bolt and No. 1 luggage compartment trim hook.

  7. REMOVE ROPE HOOK ASSEMBLY


    1. A01CE61E02
      Text in Illustration
      *1 Protective Tape

      Using a screwdriver, disengage the 2 claws.

      Tech Tips

      Tape the screwdriver tip before use.

    2. Remove the bolt and the rope hook assembly.

  8. REMOVE DECK SIDE GARNISH


    1. A01CAO7E01

      Disengage the 11 claws and 4 guides, and remove the deck side garnish RH as shown in the illustration.

  9. REMOVE INNER LUGGAGE COMPARTMENT TRIM COVER (for 60/40 Split Seat Type)


    1. A01CGI2

      Disengage the 4 claws and remove the inner luggage compartment trim cover RH as shown in the illustration.

  10. DISCONNECT REAR NO. 1 OUTER SEAT BELT ASSEMBLY (for 60/40 Split Seat Type)


    1. A01CEZD

      Remove the bolt and disconnect the floor end of the rear No. 1 seat outer belt assembly.

  11. REMOVE REAR QUARTER TRIM PANEL ASSEMBLY


    1. Remove the clip.

    2. Disengage the 14 clips, 7 claws and 2 guides.

    3. Disconnect the connectors, and remove the rear quarter trim panel assembly RH.

      A01CBNX

  12. REMOVE REAR SEAT HOOK SUB-ASSEMBLY


    1. A01CB90

      Remove the 2 bolts.

    2. A01CG8H

      Disengage the 4 claws.

    3. A01CE9YE01

      Disengage the 2 guides and remove the rear seat hook sub-assembly RH as shown in the illustration.

  13. DISCONNECT REAR NO. 2 SEAT OUTER BELT ASSEMBLY


    1. A01CD40

      Using a moulding remover, disengage the 2 claws and open the cover.

    2. A01CBQ3

      Loosen the bolt and disconnect the shoulder anchor of the rear No. 2 seat outer belt assembly.

  14. REMOVE UPPER ROOF SIDE INNER GARNISH


    1. A01CEA8

      Disengage the 2 clips, claw and guide, and remove the upper roof side inner garnish RH as shown in the illustration.

  15. REMOVE NO. 1 COOLER AIR DUCT


    1. A01CB8C

      Disengage the 2 claws and remove the cooler plate.

    2. A01CF2A

      Remove the No. 1 cooler air duct as shown in the illustration.

  16. REMOVE AMPLIFIER ANTENNA ASSEMBLY


    1. A01CAJ6

      Disconnect each connector.

    2. A01CE0Q

      Disengage the clamp and remove the bolt and amplifier antenna assembly.