PARKING BRAKE SWITCH (for LHD) REMOVAL


  1. REMOVE COWL SIDE TRIM BOARD LH


    1. A01CCIK

      Remove the clip(A).

    2. Disengage the clip, claw and 2 guides, and remove the cowl side trim board LH.

  2. REMOVE NO. 1 INSTRUMENT PANEL UNDER COVER SUB-ASSEMBLY


    1. A01CCYO

      Remove the 2 screws <B>.

    2. Disengage the 2 claws and guide.

    3. Disengage the clamp.

    4. Disconnect each connector and remove the No. 1 instrument panel under cover sub-assembly.

  3. REMOVE LOWER INSTRUMENT PANEL FINISH PANEL


    1. A01CF0E

      Disengage the 3 claws and disconnect the hood lock control cable assembly.

    2. A01CCXK

      Disengage the 3 claws and disconnect the fuel lid lock control cable assembly.

    3. A01CGDM

      Disconnect the fuel filler opening lid lock sub-assembly and remove the fuel lid lock open lever sub-assembly.

    4. A01CCWL

      Remove the 3 screws <B>.

    5. Disengage the 13 claws, clip and the 3 guides and remove the lower instrument panel finish panel as shown in the illustration.

      A01CECJ

      Note


      • Make sure to follow the order shown in the illustration to avoid damage to the lower instrument panel finish panel.

      • While supporting the knee airbag, remove the lower instrument panel finish panel.

  4. REMOVE CENTER FLOOR CARPET COVER RH


    1. A01CBO2

      Using a clip remover, remove the clip.

    2. A01CB02E01

      Disengage the 5 claws and remove the center floor carpet cover RH in the order shown in the illustration.

      Tech Tips

      Remove the center floor carpet cover RH while pushing on the instrument cluster finish panel.

  5. REMOVE CENTER FLOOR CARPET COVER LH


    1. A01CG2A

      Using a clip remover, remove the clip.

    2. A01CF5YE01

      Disengage the 4 claws and remove the center floor carpet cover LH in the order shown in the illustration.

      Tech Tips

      Remove the center floor carpet cover LH while pushing on the instrument cluster finish panel.

  6. REMOVE INSTRUMENT PANEL BOX ASSEMBLY


    1. A01CD8ZE01

      Slightly bend stoppers (A) and (B) in the directions indicated by the arrows in the illustration and pull the instrument panel box assembly until the stoppers are released.

    2. Remove the damper clip.

    3. A01CGCYE01

      Open the instrument panel box assembly to approximately 60° from its closed position. Pull it horizontally toward the rear of the vehicle to disengage the 2 hinges and remove the instrument panel box assembly.

      Note

      Pulling the instrument panel box assembly upward to remove it causes the hinges to deform. Be sure to pull out the instrument panel box horizontally.

  7. REMOVE INSTRUMENT CLUSTER FINISH PANEL ASSEMBLY


    1. A01CFL8

      Remove the bolt <C>.

    2. Disengage the 12 claws.

      Tech Tips

      First disengage the 6 claws for the right side and then pull the panel to the rear of the vehicle to disengage the 6 claws for the left side.

    3. A01CD3Y

      Disengage the 3 claws.

    4. Disconnect each connector and remove the instrument cluster finish panel assembly.

  8. SEPARATE PARKING BRAKE CONTROL PEDAL ASSEMBLY


    1. Turn back the floor carpet.

    2. A01CC39

      Remove the bolt and separate the No. 1 parking brake cable assembly from the body.

    3. A01CDDS

      Disconnect the connector and disengage the clamp.

    4. Remove the 4 nuts and separate the parking brake control pedal assembly from the body.

  9. REMOVE PARKING BRAKE SWITCH ASSEMBLY


    1. A01CCC6

      Remove the screw and parking brake switch assembly.