PARKING BRAKE PEDAL (for RHD) INSTALLATION


  1. INSTALL PARKING BRAKE CONTROL PEDAL ASSEMBLY


    1. A01CCIG

      Install the No. 1 parking brake cable assembly to the body with the 2 bolts.

      Torque:
      8.0 N*m  { 82 kgf*cm, 71 in.*lbf }
    2. A01CAZ5

      Install the No. 1 parking brake cable assembly with the bolt.

      Torque:
      8.0 N*m  { 82 kgf*cm, 71 in.*lbf }
    3. A01CDDS

      Install the parking brake control pedal assembly to the body with the 4 nuts.

      Torque:
      13 N*m  { 130 kgf*cm, 9 ft.*lbf }

    4. Connect the connector and engage the clamp.

    5. A01CBWF

      Install the No. 1 parking brake cable assembly to the body with a new clip.

    6. A01CBLB

      Engage the 2 claws to install the parking brake cable inner guide to the body.

    7. A01CE0UE01

      Connect the No. 1 parking brake cable assembly to the parking brake cable equalizer in the order shown in the illustration.

    8. A01CBSX

      Engage the boot of the No. 1 parking brake cable assembly as shown in the illustration.

  2. INSTALL FRONT FLOOR MAT PAD


    1. A01CEWG

      Install the front floor mat pad.

    2. Install the floor carpet to the original position.

  3. INSTALL REAR NO. 1 AIR DUCT


    1. A01CELR

      Engage the 2 claws to install the rear No. 1 air duct.

  4. INSTALL REAR NO. 2 AIR DUCT


    1. A01CBL5

      Engage the 2 claws to install the rear No. 2 air duct.

    2. Install the clip.

  5. INSTALL DASH PANEL INSULATOR PAD RH


    1. A01CAT2

      Install the dash panel insulator pad RH.

  6. INSTALL DRIVER SIDE KNEE AIRBAG ASSEMBLY


    1. Check that the engine switch is off.

    2. Check that the cable is disconnected from the negative (-) battery terminal.

      CAUTION:

      Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

    3. A01CBHV

      Connect the connector to the driver side knee airbag assembly.

      Note

      When connecting the airbag connector, take care not to damage the airbag wire harness.

    4. A01CERS

      Engage the 2 hooks and temporarily install the driver side knee airbag assembly.

    5. A01CG1Z

      Install the driver side knee airbag assembly with the 4 bolts firmly.

      Torque:
      10 N*m  { 102 kgf*cm, 7 ft.*lbf }

  7. INSTALL INSTRUMENT CLUSTER FINISH PANEL ASSEMBLY


    1. A01CG2C

      Engage the 15 claws.

      Tech Tips

      Before engaging the 15 claws, make sure that the claws are positioned correctly.

      Note

      Make sure that the claws are fully engaged.

    2. Install the instrument cluster finish panel assembly with the bolt <C>.

  8. INSTALL INSTRUMENT PANEL BOX ASSEMBLY


    1. A01CEC3E01

      With the instrument panel box assembly opened approximately 60° from its closed position, engage the 2 hinges horizontally.

      Note

      Engaging the hinges from the top will deform the hinges. Be sure to install the instrument panel box assembly horizontally.

    2. A01CCWJE01

      Slightly bend stoppers (A) and (B) in the directions indicated by the arrows in the illustration and engage the stoppers to install the instrument panel box assembly.

  9. INSTALL CENTER FLOOR CARPET COVER LH


    1. A01CF5Y

      Engage the 4 claws.

    2. A01CG2A

      Install the center floor carpet cover LH with the clip.

  10. INSTALL CENTER FLOOR CARPET COVER RH


    1. A01CFS0

      Engage the 4 claws.

    2. A01CDKB

      Install the center floor carpet cover RH with the 2 clips.

  11. INSTALL LOWER INSTRUMENT PANEL FINISH PANEL


    1. A01CAYP

      Engage the 3 guides and 14 claws.

      Tech Tips

      Make sure that all claws around the entire circumference of the driver side knee airbag assembly are fully engaged.

      Note

      Make sure that the claws are fully engaged.

    2. A01CCKN

      Install the lower instrument panel finish panel with the 3 screws <B>.

    3. A01CC11

      Engage the 3 claws and the fuel lid lock control cable assembly.

    4. A01CC18

      Engage the 3 claws and the hood lock control cable assembly.

  12. INSTALL NO. 1 INSTRUMENT PANEL UNDER COVER SUB-ASSEMBLY


    1. A01CE9Q

      Engage the 2 claws and DLC3.

    2. Engage the clamp.

    3. Connect the connector.

    4. A01CFFK

      Engage the 2 claws and 2 guides.

      Note

      Make sure that the claws are fully engaged.

    5. Install the No. 1 instrument panel under cover sub-assembly with the 2 screws <B>.

  13. INSTALL FRONT SEAT ASSEMBLY (for RH Side)


  14. INSTALL FRONT SEAT ASSEMBLY (for LH Side)


  15. ADJUST PARKING BRAKE

    Click here