PARKING BRAKE PEDAL (for RHD) REMOVAL


  1. REMOVE FRONT SEAT ASSEMBLY (for RH Side)


  2. REMOVE FRONT SEAT ASSEMBLY (for LH Side)


  3. REMOVE NO. 1 INSTRUMENT PANEL UNDER COVER SUB-ASSEMBLY


    1. A01CFFK

      Remove the 2 screws <B>.

    2. Disengage the 2 claws and 2 guides.

    3. A01CE9QE01

      Disengage the 2 claws and disconnect the DLC3.

    4. Disengage the clamp.

    5. Disconnect each connector and remove the No. 1 instrument panel under cover sub-assembly.

  4. REMOVE LOWER INSTRUMENT PANEL FINISH PANEL


    1. A01CC18

      Disengage the 3 claws and disconnect the hood lock control cable assembly.

    2. A01CC11

      Disengage the 3 claws and disconnect the fuel lid lock control cable assembly.

    3. A01CCKN

      Remove the 3 screws <B>.

    4. Disengage the 14 claws and the 3 guides, and remove the lower instrument panel finish panel as shown in the illustration.

      A01CCUJ

      Note


      • Make sure to follow the order shown in the illustration to avoid damage to the lower instrument panel finish panel.

      • While supporting the knee airbag, remove the lower instrument panel finish panel.

  5. REMOVE CENTER FLOOR CARPET COVER RH


    1. A01CDKB

      Using a clip remover, remove the 2 clips.

    2. A01CFS0E01

      Disengage the 4 claws and remove the center floor carpet cover RH in the order shown in the illustration.

      Tech Tips

      Remove the center floor carpet cover RH while pushing on the instrument cluster finish panel.

  6. REMOVE CENTER FLOOR CARPET COVER LH


    1. A01CG2A

      Using a clip remover, remove the clip.

    2. A01CF5YE01

      Disengage the 4 claws and remove the center floor carpet cover LH in the order shown in the illustration.

      Tech Tips

      Remove the center floor carpet cover LH while pushing on the instrument cluster finish panel.

  7. REMOVE INSTRUMENT PANEL BOX ASSEMBLY


    1. A01CD8ZE01

      Slightly bend stoppers (A) and (B) in the directions indicated by the arrows in the illustration and pull the instrument panel box assembly until the stoppers are released.

    2. Remove the damper clip.

    3. A01CGCYE01

      Open the instrument panel box assembly to approximately 60° from its closed position. Pull it horizontally toward the rear of the vehicle to disengage the 2 hinges and remove the instrument panel box assembly.

      Note

      Pulling the instrument panel box assembly upward to remove it causes the hinges to deform. Be sure to pull out the instrument panel box horizontally.

  8. REMOVE INSTRUMENT CLUSTER FINISH PANEL ASSEMBLY


    1. A01CFL8

      Remove the bolt <C>.

    2. Disengage the 12 claws.

      Tech Tips

      First disengage the 6 claws for the right side and then pull the panel to the rear of the vehicle to disengage the 6 claws for the left side.

    3. A01CD3Y

      Disengage the 3 claws.

    4. Disconnect each connector and remove the instrument cluster finish panel assembly.

  9. REMOVE DRIVER SIDE KNEE AIRBAG ASSEMBLY


    1. Check that the engine switch is off.

    2. Check that the cable is disconnected from the negative (-) battery terminal.

      CAUTION:

      Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

    3. A01CG1Z

      Remove the 4 bolts.

    4. A01CERS

      Disengage the 2 hooks and separate the driver side knee airbag assembly.

    5. A01CG8YE01

      Using a screwdriver with the tip wrapped protective tape, disconnect the connector and remove the driver side knee airbag assembly.

      Note

      When disconnecting the airbag connector, take care not to damage the airbag wire harness.

  10. LOOSEN PARKING BRAKE


    1. A01CGBCE01

      Loosen the lock nut and No. 1 wire adjusting nut to loosen the parking brake.

  11. REMOVE DASH PANEL INSULATOR PAD RH


    1. A01CAT2

      Remove the dash panel insulator pad RH.

  12. REMOVE REAR NO. 2 AIR DUCT


    1. A01CBYG

      Remove the clip.

    2. Disengage the 2 claws and remove the rear No. 2 air duct.

  13. REMOVE REAR NO. 1 AIR DUCT


    1. A01CELR

      Disengage the 2 claws and remove the rear No. 1 air duct.

  14. REMOVE FRONT FLOOR MAT PAD


    1. Turn back the floor carpet.

    2. A01CG8Z

      Remove the front floor mat pad.

  15. REMOVE PARKING BRAKE CONTROL PEDAL ASSEMBLY


    1. A01CBP9

      Slide the boot of the No. 1 parking brake cable assembly as shown in the illustration.

    2. A01CEPN

      Separate the No. 1 parking brake cable assembly from the parking brake equalizer.

    3. A01CEBV

      Disengage the 2 claws and separate the parking brake cable inner guide from the body.

    4. A01CF56

      Remove the clip and separate the No. 1 parking brake cable assembly from the body.

    5. A01CDDS

      Disconnect the connector and disengage the clamp.

    6. Remove the 4 nuts and separate the parking brake control pedal assembly from the body.

    7. A01CAZ5

      Remove the bolt and separate the No. 1 parking brake cable assembly from the body.

    8. A01CCIG

      Remove the 2 bolts and parking brake control pedal assembly from the body.