PARKING BRAKE PEDAL (for LHD) INSTALLATION


  1. INSTALL PARKING BRAKE CONTROL PEDAL ASSEMBLY


    1. A01CDDS

      Install the parking brake control pedal assembly with the 4 nuts.

      Torque:
      13 N*m  { 130 kgf*cm, 9 ft.*lbf }

    2. Connect the connector to the parking brake switch assembly and engage the clamp.

    3. Tighten the 4 bolts in the order shown in the illustration to install the No. 1 parking brake cable assembly.

      A01CCEAE01
      Text in Illustration
      *1 Tape *2 Grommet
      Torque:
      8.0 N*m  { 82 kgf*cm, 71 in.*lbf }

      Note

      Move the No. 1 parking brake cable assembly to align the edge of the tape with the grommet.

    4. Return the floor carpet.

    5. A01CBWF

      Install the No. 1 parking brake cable assembly to the body with a new clip.

    6. A01CBLB

      Engage the 2 claws to install the parking brake cable inner guide to the body.

    7. A01CE0UE01

      Connect the No. 1 parking brake cable assembly to the parking brake cable equalizer in the order shown in the illustration.

    8. A01CBSX

      Engage the clip boot of the No. 1 parking brake cable assembly as shown in the illustration.

  2. INSTALL REAR NO. 3 AIR DUCT


    1. A01CE6T

      Engage the 2 claws to install the rear No. 3 air duct.

  3. INSTALL REAR NO. 4 AIR DUCT


    1. A01CFER

      Engage the 2 claws to install the rear No. 4 air duct.

    2. Install the clip.

  4. INSTALL NO. 2 DASH PANEL INSULATOR PAD

  5. INSTALL FRONT FLOOR MAT PAD


    1. A01CEWG

      Install the front floor mat pad.

    2. Install the floor carpet to the original position.

  6. INSTALL INSTRUMENT CLUSTER FINISH PANEL ASSEMBLY


    1. A01CG2C

      Engage the 15 claws.

      Tech Tips

      Before engaging the 15 claws, make sure that the claws are positioned correctly.

      Note

      Make sure that the claws are fully engaged.

    2. Install the instrument cluster finish panel assembly with the bolt <C>.

  7. INSTALL INSTRUMENT PANEL BOX ASSEMBLY


    1. A01CEC3E01

      With the instrument panel box assembly opened approximately 60° from its closed position, engage the 2 hinges horizontally.

      Note

      Engaging the hinges from the top will deform the hinges. Be sure to install the instrument panel box assembly horizontally.

    2. A01CCWJE01

      Slightly bend stoppers (A) and (B) in the directions indicated by the arrows in the illustration and engage the stoppers to install the instrument panel box assembly.

  8. INSTALL CENTER FLOOR CARPET COVER LH


    1. A01CF5Y

      Engage the 4 claws.

    2. A01CG2A

      Install the center floor carpet cover LH with the clip.

  9. INSTALL CENTER FLOOR CARPET COVER RH


    1. A01CB02

      Engage the 5 claws.

    2. A01CBO2

      Install the center floor carpet cover RH with the clip.

  10. INSTALL LOWER INSTRUMENT PANEL FINISH PANEL


    1. A01CE7K

      Engage the 3 guides, 13 claws and clip.

      Tech Tips

      Make sure that all claws around the entire circumference of the driver side knee airbag assembly are fully engaged.

      Note

      Make sure that the claws are fully engaged.

    2. A01CCWL

      Install the lower instrument panel finish panel with the 3 screws <B>.

    3. A01CGDM

      Connect the fuel filler opening lid lock sub-assembly to the fuel lid lock open lever sub-assembly.

    4. A01CCXK

      Engage the 3 claws and the fuel lid lock control cable assembly.

    5. A01CF0E

      Engage the 3 claws and the hood lock control cable assembly.

  11. INSTALL NO. 1 INSTRUMENT PANEL UNDER COVER SUB-ASSEMBLY


    1. Engage the clamp.

    2. Connect each connector.

    3. A01CCYO

      Engage the 2 claws and guide.

      Note

      Make sure that the claws are fully engaged.

    4. Install the No. 1 instrument panel under cover sub-assembly with the 2 screws <B>.

  12. INSTALL FRONT SEAT ASSEMBLY (for RH Side)


  13. INSTALL FRONT SEAT ASSEMBLY (for LH Side)


  14. INSPECT AND ADJUST PARKING BRAKE

    Click here