FRONT AXLE HUB REMOVAL

Tech Tips


  • Use the same procedure for the RH side and LH side.

  • The procedure listed below is for the LH side.


  1. REMOVE FRONT WHEEL

  2. REMOVE FRONT AXLE SHAFT NUT


    1. A01CG4WE01

      Using SST and a hammer, release the staked part of the front axle shaft nut.

      SST
      09930-00010

      Note


      • Insert SST into the groove with the flat surface facing up.

      • Do not damage the tip of SST using a grinder.

      • Completely unstake the staked part before removing the front axle shaft nut.

      • Do not damage the threads of the drive shaft.

    2. Using a socket wrench (30 mm), remove the front axle shaft nut.

  3. SEPARATE FRONT SPEED SENSOR


    1. A01CCEP

      Remove the 2 bolts and separate the front flexible hose and the front speed sensor from the front shock absorber and steering knuckle.

    2. A01CBSW

      Remove the bolt and clamp to separate the front speed sensor from the steering knuckle.

  4. SEPARATE TIE ROD END SUB-ASSEMBLY


    1. Remove the cotter pin and nut.

    2. A01CFZ0E01

      Install SST to the tie rod end.

      SST
      09960-20010   ( 09961-02060 )

      Note

      Make sure that the upper end of the tie rod end and SST are aligned.

    3. Using SST, separate the tie rod end from the steering knuckle.

      A01CETJE01
      SST
      09960-20010   ( 09961-02010 )

      CAUTION:

      Apply grease to the bolt threads and the tip of SST.

      Note


      • Be sure to tighten the string firmly to secure SST to the steering knuckle to prevent SST from falling off.

      • Install SST with the center nut so that A and B shown in the illustration are parallel. Otherwise, the dust cover may be damaged.

      • Be sure to place the wrench on the part indicated in the illustration.

      • Do not damage the front disc brake dust cover.

      • Do not damage the ball joint dust cover.

      • Do not damage the steering knuckle.

  5. SEPARATE FRONT DISC BRAKE CALIPER ASSEMBLY


    1. A01CED2

      Remove the 2 bolts and separate the front disc brake caliper assembly from the steering knuckle.

      Note

      Use wire or an equivalent tool to keep the brake caliper from hanging down by the flexible hose.

  6. REMOVE FRONT DISC


    1. A01CEYHE01

      Put matchmarks on the front disc and front axle hub.

      Tech Tips

      The above step is not necessary when the front disc will be replaced.

    2. Remove the front disc.

  7. SEPARATE FRONT LOWER SUSPENSION ARM SUB-ASSEMBLY


    1. A01CDOO

      Remove the bolt and 2 nuts, and then pull down the front lower suspension arm sub-assembly to separate the front lower suspension arm sub-assembly from the front lower ball joint.

  8. REMOVE FRONT AXLE ASSEMBLY


    1. A01CGF8

      Using a plastic hammer, separate the front drive shaft assembly from the front axle assembly.

      Tech Tips

      If it is difficult to disengage the fitting, tap the end of the drive shaft with a brass bar and a hammer.

    2. A01CG6M

      Remove the 2 bolts and 2 nuts.

    3. Remove the front axle assembly from the front drive shaft assembly.

      Note


      • Do not deform the dust cover.

      • Do not damage the outboard joint boot.

      • Do not damage the speed sensor rotor.

      • Do not drop the front axle assembly.

      • Use the wire or an equivalent tool to hang the front drive shaft assembly.

  9. REMOVE FRONT AXLE HUB SUB-ASSEMBLY


    1. Secure the front axle assembly between aluminum plates in a vise.

      Note

      Do not overtighten the vise.

    2. A01CFHX

      Remove the 4 bolts, front axle hub sub-assembly and dust cover.

      Note

      Do not drop the front axle hub sub-assembly.