FRONT DRIVE SHAFT ASSEMBLY DISASSEMBLY


  1. SEPARATE NO. 2 FRONT AXLE INBOARD JOINT BOOT CLAMP LH


    1. A01CD7YE03

      for One Touch Type:


      1. Using a screwdriver, release the staked part of the No. 2 front axle inboard joint boot clamp LH and separate the No. 2 front axle inboard joint boot clamp LH as shown in the illustration.

    2. for Claw Engagement Type:


      1. Using needle-nose pliers, disengage the 2 claws and separate the No. 2 front axle inboard joint boot clamp LH as shown in the illustration.

  2. SEPARATE NO. 2 FRONT AXLE INBOARD JOINT BOOT CLAMP RH

    Tech Tips

    Perform the same procedure as for the LH side.

  3. SEPARATE FRONT AXLE INBOARD JOINT BOOT CLAMP LH

    Tech Tips

    Perform the same procedure as for the No. 2 front axle inboard joint boot clamp LH.

  4. SEPARATE FRONT AXLE INBOARD JOINT BOOT CLAMP RH

    Tech Tips

    Perform the same procedure as for the No. 2 front axle inboard joint boot clamp LH.

  5. SEPARATE INBOARD JOINT BOOT (for LH Side)


    1. Separate the inboard joint boot from the front drive inboard joint assembly LH.

  6. SEPARATE INBOARD JOINT BOOT (for RH Side)

    Tech Tips

    Perform the same procedure as for the LH side.

  7. REMOVE FRONT DRIVE INBOARD JOINT ASSEMBLY LH


    1. Remove the old grease from the front drive inboard joint assembly LH.

    2. A01CG48E01

      Put matchmarks on the front drive inboard joint assembly LH and front axle outboard joint shaft assembly LH.

      Note

      Do not use a punch the marks.

    3. Remove the front drive inboard joint assembly LH from the front axle outboard joint shaft assembly LH.

    4. Hold the front axle outboard joint shaft assembly LH in a vise between aluminum plates.

      Note

      Do not overtighten the vise.

    5. A01CE76

      Using a snap ring expander, remove the shaft snap ring from the front axle outboard joint shaft assembly LH.

    6. A01CAV0E02

      Put matchmarks on the front axle outboard joint shaft assembly LH and tripod.

      Note

      Do not use a punch the marks.

    7. Using a brass bar and a hammer, tap out the tripod from the front axle outboard joint shaft assembly LH.

      Note


      • Do not tap the rollers.

      • Do not drop the tripod.

    8. Remove the No. 2 front axle inboard joint boot clamp LH, inboard joint boot and front axle inboard joint boot clamp LH.

  8. REMOVE FRONT DRIVE INBOARD JOINT ASSEMBLY RH

    Tech Tips

    Perform the same procedure as for the LH side.

  9. SEPARATE FRONT DRIVE SHAFT DAMPER CLAMP LH


    1. A01CD3KE01

      Using needle-nose pliers, disengage the 2 claws and separate the 2 front drive shaft damper clamps LH as shown in the illustration.

  10. REMOVE FRONT DRIVE SHAFT DAMPER LH


    1. Remove the front drive shaft damper LH and 2 front drive shaft damper clamps LH from the front axle outboard joint shaft assembly LH.

  11. SEPARATE NO. 2 FRONT AXLE OUTBOARD JOINT BOOT CLAMP LH


    1. A01CB18

      Using a screwdriver, release the staked part of the No. 2 front axle outboard joint boot clamp LH and separate the No. 2 front axle outboard joint boot clamp LH as shown in the illustration.

  12. SEPARATE NO. 2 FRONT AXLE OUTBOARD JOINT BOOT CLAMP RH

    Tech Tips

    Perform the same procedure as for the LH side.

  13. SEPARATE FRONT AXLE OUTBOARD JOINT BOOT CLAMP LH

    Tech Tips

    Perform the same procedure as for the No. 2 front axle outboard joint boot clamp LH.

  14. SEPARATE FRONT AXLE OUTBOARD JOINT BOOT CLAMP RH

    Tech Tips

    Perform the same procedure as for the No. 2 front axle outboard joint boot clamp LH.

  15. REMOVE OUTBOARD JOINT BOOT (for LH Side)


    1. Remove the front axle outboard joint boot clamp LH, outboard joint boot and No. 2 front axle outboard joint boot clamp LH from the front axle outboard joint shaft assembly LH.

    2. Remove the old grease from the outboard joint.

  16. REMOVE OUTBOARD JOINT BOOT (for RH Side)

    Tech Tips

    Perform the same procedure as for the LH side.

  17. REMOVE FRONT DRIVE SHAFT DUST COVER LH


    1. A01CF6RE02

      Using SST and a press, remove the front drive shaft dust cover LH from the front drive inboard joint assembly LH.

      SST
      09950-00020

      Note

      Do not drop the front drive inboard joint assembly LH.

  18. REMOVE FRONT DRIVE SHAFT DUST COVER RH


    1. A01CB73

      Using a press, remove the front drive shaft dust cover RH.

      Note

      Do not drop the front drive inboard joint assembly RH.

  19. REMOVE DRIVE SHAFT BEARING CASE SUB-ASSEMBLY (for RH Side)


    1. Hold the drive shaft bearing case sub-assembly in a vise between aluminum plates.

      Note

      Do not overtighten the vise.

    2. A01CGB1E04

      Using a screwdriver, remove the bearing case snap ring from the drive shaft bearing case sub-assembly as shown in the illustration.

    3. A01CATP

      Using a press, remove the drive shaft bearing case sub-assembly from the front drive inboard joint assembly RH.

      Note

      Do not drop the front drive inboard joint assembly RH.

  20. REMOVE FRONT DRIVE SHAFT DUST COVER (for RH Side)


    1. A01CES3E08

      Using SST and a press, remove the front drive shaft dust cover from the front drive inboard joint assembly RH.

      SST
      09950-00020

      Note

      Do not drop the front drive inboard joint assembly RH.

  21. REMOVE FRONT DRIVE SHAFT BEARING (for RH Side)


    1. A01CDZO

      Using a snap ring expander, remove the snap ring.

    2. A01CE38E02

      Using SST and a press, remove the front drive shaft bearing from the front drive inboard joint assembly RH.

      SST
      09527-10011

      Note

      Do not drop the front drive inboard joint assembly RH.

    3. Remove the bearing case snap ring.