AUTOMATIC TRANSAXLE SYSTEM, Diagnostic DTC:P0791, P0793

DTC Code DTC Name
P0791 Intermediate Shaft Speed Sensor "A" Circuit
P0793 Intermediate Shaft Speed Sensor "A"

DESCRIPTION

This sensor detects the rotation speed of the counter gear which shows the output speed of transaxle. By comparing the input turbine speed signal (NT) with the counter gear speed sensor signal (NC), the TCM detects the shift timing of the gears and appropriately controls the engine torque and hydraulic pressure according to various conditions, thus, providing smooth gear shifts.

A01CEI2E01
DTC No. DTC Detection Condition Trouble Area
P0791 When the speed sensor input voltage is either more than 1.9 V or less than 0.1 V for 2 seconds or more. (1-trip detection logic)

  • Transmission revolution sensor (speed sensor NC)

  • Transmission wire

  • TCM
P0793 When the vehicle speed is 25 km/h (15.5 mph) or higher, the counter gear speed is less than 300 rpm for 2 seconds or more. (1-trip detection logic)

MONITOR DESCRIPTION

The NT terminal of the TCM detects a revolution signal from the speed sensor (NT) (input RPM). The TCM calculates a gear shifts by comparing the speed sensor (NT) with the speed sensor (NC).

While the vehicle is operating in 2nd, 3rd, 4th or 5th gear with the shift lever in D, if the input shaft revolution is less than 300 rpm*1 although the output shaft revolution is more than 1000 rpm*2, the TCM interprets this as a fault, illuminates the MIL and stores the DTC.

*1: Pulse is not output or is irregularly output.

*2: The vehicle speed is 50 km/h (31 mph) or more.

WIRING DIAGRAM

A01CEX3E18

INSPECTION PROCEDURE


  1. DATA LIST

    Tech Tips

    Using the intelligent tester to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.

    Note

    In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.


    1. Warm up the engine.

    2. Turn the engine switch off.

    3. Connect the intelligent tester to the DLC3.

    4. Turn the engine switch on (IG).

    5. Turn the intelligent tester on.

    6. Enter the following menus: Powertrain / ECT / Data List.

    7. According to the display on the intelligent tester, read the Data List.

      Item Measurement Item/Range (display) Normal Condition
      SPD (NC) Counter Gear Speed/ display: 50 r/min -

      Tech Tips


      • SPD (NC) is always 0 while driving: Open or short in the sensor or circuit.

      • SPD (NC) is always more than 0 and less than 300 rpm while driving the vehicle at 50 km/h (31 mph) or more: Sensor trouble, improper installation, or intermittent connection trouble of the circuit.

PROCEDURE


  1. INSPECT SPEED SENSOR (SENSOR INSTALLATION)


    1. Remove the valve body assembly.

    2. A01CFQD

      Make sure that the connector is properly connected, and check the speed sensor installation.

      OK
      The installation bolts are tightened properly and there is no clearance between the sensor and transaxle case.

    NG

    REPAIR OR REPLACE SPEED SENSOR Click here

    OK

  2. INSPECT TRANSMISSION WIRE


    1. A01CCV7E02

      Remove the TCM.

    2. Disconnect the speed sensor connector from the transmission wire.

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Condition Condition Specified Condition
      3 (NCO) sensor side - 3 (NCO) TCM side Always Below 1 Ω
      4 (NCB) sensor side - 4 (NCB) TCM side Always Below 1 Ω
      3 (NCO) sensor side - Body ground Always 10 kΩ or higher
      4 (NCB) sensor side - Body ground Always 10 kΩ or higher
      3 (NCO) sensor side - All other terminals except 4 (NCB) sensor side Always 10 kΩ or higher
      4 (NCB) sensor side - All other terminals except 3 (NCO) sensor side Always 10 kΩ or higher

    NG

    REPLACE TRANSMISSION WIRE Click here

    OK

  3. REPLACE SPEED SENSOR


    1. Click here.


    NEXT

  4. CHECK IF DTC OUTPUT RECURS (SEE IF DTC P0791 AND/OR P0793 IS OUTPUT AGAIN)


    1. Connect the intelligent tester to the DLC3.

    2. Start the engine and turn the intelligent tester on.

    3. Enter the following menus: / ECT / DTC / Clear.

      Tech Tips

      Write down the currently output DTCs before clearing them.

    4. Perform the monitor drive pattern Click here.

    5. Enter the following menus: / ECT / DTC.

    6. Read the DTCs using the intelligent tester.

      Result
      Display (DTC Output) Proceed to
      Only "P0791 or P0793" is output A
      No output B

    B

    END

    A

    REPLACE TCM Click here