OIL AND OIL FILTER REPLACEMENT

CAUTION:


  • Prolonged and repeated contact with engine oil will result in the removal of natural oils from the skin, leading to dryness, irritation and dermatitis. In addition, used engine oil contains potentially harmful contaminants which may cause skin cancer.

  • Precautions should be taken when replacing engine oil to minimize the risk of your skin making contact with used engine oil. Protective clothing and gloves that cannot be penetrated by oil should be worn. The skin should be washed with soap and water or waterless hand cleaner to remove any used engine oil thoroughly. Do not use gasoline, thinners, or solvents.

  • In order to preserve the environment, used oil and used oil filters must be disposed of at designated disposal sites.


  1. REMOVE NO. 1 ENGINE UNDER COVER

  2. DRAIN ENGINE OIL


    1. Remove the oil filler cap.

    2. Remove the oil drain plug and drain the oil into a container.

    3. Clean the oil drain plug.

    4. Install the oil drain plug with a new gasket.

      Torque:
      40 N*m  { 408 kgf*cm, 30 ft.*lbf }

  3. REMOVE OIL FILTER ELEMENT


    1. A01CC3PE01
      Text in Illustration
      *1 Pipe
      *2 Hose

      Connect a hose with an inside diameter of 15 mm (0.59 in.) to the pipe.

    2. A01CFBZ

      Remove the oil filter drain plug from the oil filter cap.

    3. A01CE2IE02
      Text in Illustration
      *1 Cap
      *2 O-ring
      *3 Pipe

      Insert the pipe with the hose into the oil filter cap.

      Note

      Be sure to insert the pipe with the O-ring installed on the oil filter cap side.

      Tech Tips

      Place the hose end into a container before draining oil from the hose.

    4. A01CCIC

      Make sure that the oil is completely drained, and remove the pipe and O-ring.

      Tech Tips

      Be sure to turn the pipe in the direction of the arrow to remove it.

    5. A01CCQTE01

      Using SST, remove the oil filter cap.

      SST
      09228-06501
    6. A01CC75E06
      Text in Illustration
      *1 Oil Filter Element
      *2 Oil Filter Cap
      *3 O-ring

      Remove the oil filter element and O-ring from the oil filter cap.

      Note

      Do not use any tools to remove the O-ring in order to prevent the cap from being damaged. Be sure to remove it by hand.

  4. INSTALL OIL FILTER ELEMENT


    1. Clean the inside of the oil filter cap, threads and O-ring groove.

    2. A01CCXOE01
      Text in Illustration
      *1 O-ring
      *a CORRECT
      *b INCORRECT

      Apply a light coat of engine oil to a new O-ring and install it to the oil filter cap.

      Note


      • Be sure to install the O-ring in the proper location, otherwise oil may leak.

      • Do not twist the O-ring.

    3. Install a new oil filter element to the oil filter cap.

    4. Remove all dirt and foreign matter from the installation surface and the inside of the cap on the engine side.

    5. Apply a light coat of engine oil to the O-ring again and install the oil filter cap.

      Note

      Make sure that the O-ring does not get caught between the parts.

    6. A01CDR7E01
      Text in Illustration
      *1 Oil Filter Cap
      *2 O-ring
      *3 Oil Filter Bracket
      *a No Gap

      Using SST, install the oil filter cap.

      SST
      09228-06501
      Torque:
      25 N*m  { 255 kgf*cm, 18 ft.*lbf }

      Note

      After tightening the oil filter cap, make sure that there is no gap and that the O-ring is not protruding.

    7. A01CE2RE03
      Text in Illustration
      *1 O-ring

      Apply a light coat of engine oil to a new O-ring and install it to the oil filter cap.

      Note

      Remove all dirt and foreign matter from the installation surface.

    8. Install the oil filter drain plug to the oil filter cap.

      Torque:
      13 N*m  { 127 kgf*cm, 10 ft.*lbf }

      Note

      Make sure that the O-ring does not get caught between the parts.

  5. ADD ENGINE OIL


    1. A01CC54

      Add clean engine oil and install the oil filler cap.

      Note

      Do not allow engine oil adhere to the moving parts of the belt tensioner, as this may cause malfunctions.

      If engine oil is on the location indicated by the arrow, replace the belt tensioner.

      Standard Oil Grade
      Oil Grade Oil Viscosity (SAE)

      • API grade SL "Energy-Conserving", SM "Energy-Conserving", SN "Resource-Conserving" or ILSAC multigrade engine oil

      • 0W-20

      • 5W-20

      • 5W-30

      • 10W-30
      API grade SL, SM or SN multigrade engine oil

      • 15W-40

      • 20W-50
      Standard Capacity
      Item Standard Condition
      Drain and refill with oil filter change 6.1 liters (6.4 US qts, 5.4 lmp. qts)
      Drain and refill without oil filter change 5.7 liters (6.0 US qts, 5.0 lmp. qts)
      Dry fill 6.8 liters (7.2 US qts, 6.0 lmp. qts)

  6. INSPECT FOR OIL LEAK


    1. Start the engine. Check for engine oil leaks from the connected parts of the oil filter cap and oil filter drain plug.

  7. INSTALL NO. 1 ENGINE UNDER COVER