Click here

EXHAUST PIPE INSTALLATION

Click here
Click here Click here
  1. Click here

    INSTALL HEATED OXYGEN SENSOR


    1. A01CDQWE01

      Using SST, install the heated oxygen sensor.

      Table 1. Text in Illustration
      *1

      Fulcrum Length

      30 mm
      09224-00010
      without SST
      44 N*m 449 kgf*cm 32 ft.*lbf
      with SST
      39 N*m 398 kgf*cm 29 ft.*lbf
      Note:

      • The "with SST" torque value is effective when using SST with a fulcrum length of 30 mm (1.18 in.).

      • The "with SST" torque value is effective when using a torque wrench with a fulcrum length of 260 mm (10.23 in.) (Click here).

      • This torque value is effective when SST is parallel to the torque wrench.

    2. A01CD9G

      Connect the heated oxygen sensor connector.

  2. Click here

    INSTALL FRONT EXHAUST PIPE ASSEMBLY


    1. A01CBMY

      Using a vernier caliper, measure the free length of the compression springs.

      Minimum length
      41.5 mm (1.64 in.)

      If the free length is less than the minimum, replace the compression spring.

    2. Fully insert a new gasket to the exhaust manifold converter sub-assembly.

    3. A01CFWCE15

      Using a plastic hammer and wooden block, tap in the new gasket until its surface is flush with the exhaust manifold converter sub-assembly.

      Table 2. Text in Illustration
      *1 Exhaust Manifold Converter Sub-assembly
      *2 Gasket
      *3 Wooden Block
      Note:

      • Be sure to install the gasket in the correct direction.

      • Do not reuse the gasket.

      • Do not damage the gasket.

      • Do not push in the gasket by using the exhaust pipe when connecting it.

    4. Install the front exhaust pipe assembly with the 2 bolts and 2 compression springs.

      43 N*m 440 kgf*cm 32 ft.*lbf

    5. Connect the oxygen sensor connector.

  3. Click here

    INSTALL CENTER EXHAUST PIPE ASSEMBLY


    1. Install a new gasket to the front exhaust pipe assembly.

    2. Connect the center exhaust pipe assembly to the 3 exhaust pipe supports.

    3. Install the center exhaust pipe assembly with the 2 bolts.

      43 N*m 440 kgf*cm 32 ft.*lbf
  4. Click here

    INSTALL TAIL EXHAUST PIPE ASSEMBLY


    1. A01CBMY

      Using a vernier caliper, measure the free length of the compression springs.

      Minimum length
      38.5 mm (1.52 in.)

      If the free length is less than the minimum, replace the compression spring.

    2. Fully insert a new gasket to the center exhaust pipe assembly.

    3. A01CFWCE17

      Using a plastic hammer and wooden block, tap in the new gasket until its surface is flush with the center exhaust pipe assembly.

      Table 3. Text in Illustration
      *1 Center Exhaust Pipe Assembly
      *2 Gasket
      *3 Wooden Block
      Note:

      • Be sure to install the gasket in the correct direction.

      • Do not reuse the gasket.

      • Do not damage the gasket.

      • Do not push in the gasket by using the exhaust pipe when connecting it.

    4. Connect the tail exhaust pipe assembly to the 2 exhaust pipe supports.

    5. Install the tail exhaust pipe assembly with the 2 bolts and 2 compression springs.

      43 N*m 440 kgf*cm 32 ft.*lbf
  5. Click here

    INSPECT FOR EXHAUST GAS LEAK