Click here

THROTTLE BODY REMOVAL

Click here
Click here Click here
  1. Click here

    REMOVE NO. 1 ENGINE UNDER COVER

  2. Click here

    DRAIN ENGINE COOLANT

    CAUTION:

    Do not remove the reserve tank cap, cylinder block drain cock plugs or radiator drain cock plug while the engine and radiator assembly are still hot. Pressurized, hot engine coolant and steam may be released and cause serious burns.


    1. A01CD8ME01

      Connect a hose with an inside diameter of 9 mm (0.354 in.) to the radiator drain cock as shown in the illustration.

      Table 1. Text in Illustration
      *1 No. 1 Engine Under Cover
      *a Hose

    2. Loosen the radiator drain cock plug.

    3. Remove the reserve tank cap. Then drain the engine coolant.

    4. Loosen the cylinder block drain cock plug (for Bank 1).

    5. A01CDICE01

      Loosen the cylinder block drain cock plug (for Bank 2, w/ Cylinder Block Drain Cock Plug).

      Table 2. Text in Illustration
      *1 Radiator Reserve Tank *2 Reserve Tank Cap
      *3 Radiator Drain Cock Plug *4 Air Drain Cock Plug
      *5 Cylinder Block Drain Cock Plug (for Bank 1) *6 Cylinder Block Drain Cock Plug (for Bank 2, w/ Cylinder Block Drain Cock Plug)
      Tip:

      Collect the engine coolant in a container and dispose of it according to the regulations in your area.

    6. Disconnect a hose with an inside diameter of 9 mm (0.354 in.) from the radiator drain cock.

  3. Click here

    REMOVE WINDSHIELD WIPER MOTOR AND LINK ASSEMBLY


    1. Remove the windshield wiper motor and link assembly (Click here).

  4. Click here

    SEPARATE BRAKE MASTER CYLINDER RESERVOIR ASSEMBLY


    1. A01CBAK

      Remove the 2 nuts and separate the brake master cylinder reservoir with bracket from the outer cowl top panel.

  5. Click here

    REMOVE COWL TOP PANEL OUTER SUB-ASSEMBLY


    1. A01CED5

      Apply protective tape as shown in the illustration.

      Table 3. Text in Illustration
      A01CC81 Protective Tape
    2. A01CCFB

      Disconnect the 2 clamps from the outer cowl top panel.

    3. Remove the 8 bolts.

    4. A01CDT7

      Remove the outer cowl top panel as shown in the illustration.

  6. Click here

    REMOVE V-BANK COVER SUB-ASSEMBLY


    1. A01CCP4

      Hold the front of the V-bank cover sub-assembly and raise it to disengage the 2 clips on the front of the cover. Continue to raise the cover to disengage the clip on the rear of the cover and remove the V-bank cover sub-assembly.

      Note:

      Attempting to disengage both front and rear clips at the same time may cause the cover to break.

  7. Click here

    REMOVE AIR CLEANER CAP SUB-ASSEMBLY


    1. A01CBVZE01

      Separate the mass air flow meter connector and 2 wire harness clamps.

    2. Separate the purge line hose.

    3. A01CAN5

      Separate the ventilation hose.

    4. Loosen the hose clamp and separate the air cleaner hose from the throttle body.

    5. A01CB66

      Release the 2 clamps and remove the air cleaner cap sub-assembly.

  8. Click here

    REMOVE THROTTLE BODY


    1. A01CBKZ

      Disconnect the 2 water by-pass hoses from the throttle body.

    2. A01CBSJE01

      Disconnect the throttle body connector and wire harness clamp.

    3. Remove the 4 bolts, throttle body and wire harness clamp stay.

    4. Remove the gasket from the intake air surge tank assembly.