Click here

SFI SYSTEM, Diagnostic DTC:P0010

Click here
Click here Click here
DTC Code DTC Name
P0010 Camshaft Position "A" Actuator Circuit (Bank 1)
Click here

DESCRIPTION

The Variable Valve Timing (VVT) system includes the ECM, intake camshaft timing oil control valve assembly and VVT controller. The ECM sends a target duty-cycle control signal to the intake camshaft timing oil control valve assembly. This control signal regulates the oil pressure supplied to the VVT controller. Camshaft timing control is performed according to engine operating conditions such as intake air volume, throttle valve position and engine coolant temperature. The ECM controls the camshaft timing oil control valve assembly, based on the signals transmitted from several sensors. The VVT controller regulates the intake camshaft angle using oil pressure through the camshaft timing oil control valve assembly. As a result, the relative positions of the camshaft and crankshaft are optimized, the engine torque and fuel economy improve, and the exhaust emissions decrease under overall driving conditions. The ECM detects the actual intake valve timing using signals from the camshaft and crankshaft position sensors, and performs feedback control. This is how the target intake valve timing is verified by the ECM.

DTC No. DTC Detection Condition Trouble Area
P0010

Open or short in camshaft timing oil control valve assembly circuit

(1 trip detection logic)

  • Open or short in camshaft timing oil control valve assembly circuit

  • Camshaft timing oil control valve assembly

  • ECM
Click here

WIRING DIAGRAM

Click here

INSPECTION PROCEDURE

Tip:

Read freeze frame data using the intelligent tester. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.

Click here

PROCEDURE


  1. Click here

    PERFORM ACTIVE TEST USING INTELLIGENT TESTER (OPERATE CAMSHAFT TIMING OIL CONTROL VALVE)


    1. Connect the intelligent tester to the DLC3.

    2. Start the engine.

    3. Turn the tester on.

    4. Enter the following menus: Powertrain / Engine and ECT / Active Test / Control the VVT System (Bank 1).

    5. Check the engine speed while operating the camshaft timing oil control valve assembly using the tester.

      OK
      Tester Operation Specified Condition
      OFF Normal engine speed
      ON

      Engine idles roughly or stalls

      (soon after camshaft timing oil control valve assembly switched from off to on)

  2. Click here

    INSPECT CAMSHAFT TIMING OIL CONTROL VALVE ASSEMBLY


    1. A01CD1KE08

      Remove the camshaft timing oil control valve assembly.

    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      1 - 2 20°C (68°F) 6.9 to 7.9 Ω
      Table 1. Text in Illustration
      *1

      Component without harness connected

      (Camshaft Timing Oil Control Valve Assembly)
    3. A01CG4KE05

      Connect the positive (+) battery terminal to terminal 1 and connect the negative (-) battery terminal to terminal 2. Check the valve operation.

      OK
      Valve moves quickly.

    4. Reinstall the camshaft timing oil control valve assembly.


  3. Click here

    CHECK HARNESS AND CONNECTOR (CAMSHAFT TIMING OIL CONTROL VALVE ASSEMBLY - ECM)


    1. Disconnect the camshaft timing oil control valve assembly connector.

    2. Disconnect the ECM connector.

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance (Check for Open)
      Tester Connection Condition Specified Condition
      D49-1 - D41-100 (OC1+) Always Below 1 Ω
      D49-2 - D41-123 (OC1-) Always Below 1 Ω
      Standard Resistance (Check for Short)
      Tester Connection Condition Specified Condition
      D49-1 or D41-100 (OC1+) - Body ground Always 10 kΩ or higher
      D49-2 or D41-123 (OC1-) - Body ground Always 10 kΩ or higher

    4. Reconnect the camshaft timing oil control valve assembly connector.

    5. Reconnect the ECM connector.


  4. Click here

    REPLACE ECMClick here

  5. Click here

    REPAIR OR REPLACE HARNESS OR CONNECTOR (CAMSHAFT TIMING OIL CONTROL VALVE ASSEMBLY - ECM)

  6. Click here

    REPLACE CAMSHAFT TIMING OIL CONTROL VALVE ASSEMBLYClick here

  7. Click here

    CHECK FOR INTERMITTENT PROBLEMSClick here