REPAIR INSTRUCTION CUSTOMIZE PARAMETERS

Tech Tips

The following items can be customized.

Note


  • When the customer requests a change in a function, first make sure that the function can be customized.

  • Be sure to make a note of the current settings before customizing.

  • When troubleshooting a function, first make sure that the function is set to the default setting.


  1. TOYOTA PARKING ASSIST-SENSOR SYSTEM


    1. Customizing with the intelligent tester

      Warning
      Display Default Content Setting Relevant ECU
      Rr Sensor Onset Range Wide Sets the buzzer activation range for the rear center sensors.

      Narrow or Wide


      • Narrow: 600 mm (23.6 in.)

      • Wide: 1500 mm (59.1 in.)

      		 Clearance warning ECU assembly
      Keep Sense Buzzer Avail Sounds the buzzer when the distance between the vehicle and obstacle does not change for more than 3 seconds.

      Not Avail or Avail


      • Not Avail: Not Available

      • Avail: Available

      		 Clearance warning ECU assembly
      Fr & Rr Buzzer Volume M2 Changes the buzzer volume setting.

      L, M1, M2, M3 or H


      • L: Low volume

      • M1: Medium low volume

      • M2: Medium volume

      • M3: Medium high volume

      • H: High volume

      		 Clearance warning ECU assembly
      Sensor
      Display Default Content Setting Relevant ECU
      Sensor Condition N Avail Makes the front sensors available when the shift lever is in N.

      Not Avail or Avail


      • Not Avail: Not Available

      • Avail: Available

      		 Clearance warning ECU assembly
      Reverse Range Front Sensor F Changes the operation setting for the front sensors when the shift lever is in R.

      F or F Stop


      • F: Front sensors are available

      • F Stop: Front sensors are not available

      		 Clearance warning ECU assembly
      Non P/R Range Rear Sensor R Stop Changes the operation setting for the rear sensors when the shift lever is in any position other than P or R.

      R, Rcrn or R Stop


      • R: All rear sensors are available

      • Rcrn: Rear corner sensors are available

      • R Stop: All rear sensors are not available

      		 Clearance warning ECU assembly
      Display
      Display Default Content Setting Relevant ECU
      Display Mode*1 All The display mode setting (when the Toyota parking assist-sensor system is normal). All or Undisp Clearance warning ECU assembly

      • *1: This item is used to allow or prevent the Toyota parking assist-sensor system from being displayed on the navigation display. For this model, some vehicles are not equipped with the navigation system. On these vehicles, the Display Mode item is not available.

    2. Customizing with the Multi-display (w/ Navigation System (for HDD))


      1. Turn the engine switch on (IG).

      2. Turn the clearance sonar main switch on.

      3. Enter the following menus: Setup / Vehicle / TOYOTA park assist.

      4. Select the setting by referring to the table below.

        Display Default Content Setting Relevant ECU
        Alert volume 3 Sets the buzzer alert volume.

        1, 2, 3, 4 or 5


        • 1: Low volume

        • 2: Medium low volume

        • 3: Medium volume

        • 4: Medium high volume

        • 5: High volume

        		 Clearance warning ECU assembly
        Display On The display mode setting (when the Toyota parking assist-sensor system is normal). On or Off Clearance warning ECU assembly
        Distance Wide Sets the buzzer activation range for the rear center sensors.

        Narrow or Wide


        • Narrow: 600 mm (23.6 in.)

        • Wide: 1500 mm (59.1 in.)

        		 Clearance warning ECU assembly

  2. POWER DOOR LOCK CONTROL SYSTEM


    1. Customizing with the intelligent tester

      Door Lock
      Display Default Content Setting Relevant ECU
      Auto Lock* ON Function that locks all doors when the vehicle speed reaches a certain level. OFF or ON Main body ECU (Multiplex network body ECU)
      Auto Lock/Shift* OFF With the engine running and all doors closed, function that locks all doors when the shift lever is moved from P to any position other than P. OFF or ON Main body ECU (Multiplex network body ECU)
      Auto Unlock/Shift* OFF Function that unlocks all doors when the shift lever is moved to P from any position other than P while the engine switch is on (IG). OFF or ON Main body ECU (Multiplex network body ECU)
      All Unlock/Open-Close* OFF Function that unlocks the other doors when the driver side door is opened within 10 seconds after the engine switch is turned off. OFF or ON Main body ECU (Multiplex network body ECU)

      • *: w/ Auto Lock Function

    2. Customizing with the Multi-display (w/ Navigation System (for HDD))


      1. Turn the engine switch on (IG).

      2. Enter the following menus: SETUP / Vehicle / Vehicle Customization / Door lock setting.

      3. Select the setting by referring to the table below.

        Display Default Content Setting Relevant ECU
        Speed sensitive auto locking* On Function that locks all doors when the vehicle speed reaches a certain level. On or Off Main body ECU (Multiplex network body ECU)
        Auto lock by shift from P* Off With the engine running and all doors closed, function that locks all doors when the shift lever is moved from P to any position other than P. On or Off Main body ECU (Multiplex network body ECU)
        Auto unlock by shift to P* Off Function that unlocks all doors when the shift lever is moved to P from any position other than P while the engine switch is on (IG). On or Off Main body ECU (Multiplex network body ECU)
        Auto unlock by driver door* Off Function that unlocks the other doors when the driver side door is opened within 10 seconds after the engine switch is turned off. On or Off Main body ECU (Multiplex network body ECU)

        • *: w/ Auto Lock Function

  3. WIRELESS DOOR LOCK CONTROL SYSTEM (w/ Smart Entry and Start System)


    1. Customizing with the intelligent tester

      Wireless Door Lock Control System
      Display Default Content Setting Relevant ECU
      Wireless Control ON Function that turns wireless door lock OFF or ON Main body ECU (Multiplex network body ECU)
      Hazard Answer Back ON

      When the doors are locked by wireless operation, the hazard warning lights flash once.

      When the doors are unlocked by wireless operation, the hazard warning lights flash twice.

      		 OFF or ON Main body ECU (Multiplex network body ECU)
      Open Door Warning* ON The buzzer sounds when lock is pressed when any of the doors are ajar. OFF or ON Main body ECU (Multiplex network body ECU)
      Auto Lock Time 30 s Function that regulates the interval between unlocking and automatic relocking of doors 30 s, 60 s or 120 s Main body ECU (Multiplex network body ECU)
      Wireless Buzzer Resp* ON Wireless door lock buzzer response OFF or ON Main body ECU (Multiplex network body ECU)

      • *: w/ Wireless Buzzer Function

    2. Customizing with the Multi-display (w/ Navigation System (for HDD))


      1. Turn the engine switch on (IG).

      2. Enter the following menus: SETUP / Vehicle / Vehicle Customization / Door lock setting.

      3. Select the setting by referring to the table below.

        Display Default Content Setting Relevant ECU
        Lock/unlock feedback-lights On

        When the doors are locked by wireless operation, the hazard warning lights flash once.

        When the doors are unlocked by wireless operation, the hazard warning lights flash twice.

        		 On or Off Main body ECU (Multiplex network body ECU)

  4. SMART ENTRY AND START SYSTEM (for Entry Function)


    1. Customizing with the intelligent tester

      Entry & Start
      Tester Display Default Content Setting
      Ignition Available Area ALL Function that switches the entry ignition detection area FRONT or ALL
      Park Wait Time 2.5s Function to set waiting time to permit opening door after door is locked with entry lock function 0.5 s, 1.5 s, 2.5 s or 5 s
      Back Door Opening Operation LONG Function to open the back door when the driver has the electrical key and presses back door opener switch assembly (opener switch) LONG, TWICE or OFF
      Key Low Battery Warning ON Function to warn driver that key battery is low ON or OFF

    2. Customizing with the Multi-display (w/ Navigation System (for HDD))


      1. Turn the engine switch on (IG).

      2. Enter the following menus: SET UP / Vehicle / Vehicle Customization / Door lock settings.

      3. Select the setting by referring to the table below.

        Tester Display Default Content Setting
        Entry and start system On Function that enables or disables the smart entry and start system. On or Off

  5. Electrical Key Cancel

    The electrical key cancel operation disables the following functions:


    • Entry Unlock/Lock

    • Entry Ignition

    • Entry Back Door Open

    • Electrical Key Lock-in Prevention

    • Warning

    • Memory Call


    1. The operation procedures are as follows:

      Precondition:

      Engine switch off, driver side door closed and unlocked.


      1. Unlock the driver side door once with the UNLOCK switch of the electrical key.

      2. Open the driver door within 5 seconds.

      3. Unlock the driver side door twice with the UNLOCK switch of the electrical key within 5 seconds.

      4. Close and open the driver door twice within 30 seconds.

        (Driver door: Close → Open → Close → Open)

      5. Unlock the driver side door twice with the UNLOCK switch of the electrical key within 5 seconds.

      6. Close and open the driver door within 30 seconds.

        (Driver door: Close → Open)

      7. Close the driver door within 5 seconds.

        When electrical key cancel is activated, the wireless door lock buzzer sounds twice.

        To return to the original condition, perform the procedures again. When the original condition is returned, the wireless door lock buzzer sounds once.

  6. SMART ENTRY AND START SYSTEM (for Start Function)

    Entry & Start
    Display (Item) Default Contents Setting
    Ignition Available Area (Entry ignition available area) All Function to choose the available area for electrical key to start the engine and cancel the steering lock Front or All

  7. LIGHTING SYSTEM (INT)

    Illuminated Entry
    Tester Display Default Content Setting
    Lighting Time 15 s Changes the lighting time after closing all of the doors. (It will fade out immediately in case of turning the engine switch from off to on (ACC or IG).) 7.5 s, 15 s or 30 s
    Illumination System ON Lights up the footwell lights and ceiling lights when one of the following occurs: the engine switch is turned on (IG), or any door is unlocked or opened. ON or OFF
    Light Control ON Dims (ON setting) or turns off (OFF setting) the footwell lights under the following conditions: engine switch on (IG), shift lever not in P, and all doors closed. ON or OFF
    I/L ON W/Door Key Unlock ON Lights up the personal light LH, personal light RH, center room light LH, center room light RH and engine switch illumination when doors are unlocked using a mechanical key or door control transmitter. ON or OFF
    I/L when ACC OFF ON Lights up the personal light LH, personal light RH, center room light LH, center room light RH and engine switch illumination when the engine switch is turned from on (ACC or IG) to off. ON or OFF

  8. METER / GAUGE SYSTEM

    Combination Meter
    Tester Display Default Content Setting
    Driver Side Seatbelt Warning Buzzer*1 ON Function to turn on/off the seat belt warning buzzer. ON, OFF
    Front Passenger Side Seatbelt Warning Buzzer*1 ON Function to turn on/off the seat belt warning buzzer. ON, OFF
    ECO Drive Indicator Zone ON Function to turn on/off the ECO zone display in the multi-information display ON, OFF

    • *1: This setting is only valid for the buzzer which sounds at the 20 km/h (12 mph) or more.

  9. FRONT POWER SEAT CONTROL SYSTEM (for Driver Side)


    1. Customizing with the intelligent tester

      Display Default Content Setting Relevant ECU
      Seat Travel Distance Short Allows customizing of the seat travel distance for the power easy access system OFF/Short/Normal Position control ECU and switch assembly

    2. Customizing with the Multi-display (w/ Navigation System (for HDD))


      1. Turn the engine switch on (IG).

      2. Enter the following menus: SETUP / Vehicle / Vehicle Customization / Other vehicle settings.

      3. Select the setting by referring to the table below.

        Display Default Content Setting Relevant ECU
        Driver's seat easy exit Partial Allows customizing of the seat travel distance for the power easy access system Off/Partial/Full Position control ECU and switch assembly

  10. SEAT BELT WARNING SYSTEM

    Combination Meter
    Tester Display Default Content Setting
    Driver Side Seatbelt Warning Buzzer* ON Function to sound the seat belt warning buzzer ON or OFF
    Front Passenger Side Seatbelt Warning Buzzer* ON Function to sound the seat belt warning buzzer ON or OFF

    • *: This setting is only valid for the buzzer which sounds at 20 km/h (12 mph) or more.

  11. AIR CONDITIONING SYSTEM


    1. Customizing with the intelligent tester

      Air Conditioner
      Display (Item) Default Content Setting
      Set Temperature Shift Normal Function to perform control with the shifted temperature versus the displayed temperature -2C, -1C, Normal, +1C, +2C
      Evaporator Control Automatic Function to set the evaporator control to the AUTOMATIC position (AUTO) to save power or to the coldest position (MANUAL) to dehumidify the air and to prevent the windows from fogging up Automatic or Manual
      Compressor/Air Inlet DEF operation Link Function to automatically turn the A/C on linked with the FRONT DEF button when the A/C is off Link or Normal
      Compressor Mode Automatic Function to turn the A/C ON automatically by pressing the AUTO button when the blower is ON and the A/C is OFF Automatic or Manual
      Air Inlet Mode Automatic In case of turning the A/C ON to cool the cabin down quickly, this is the function to change the mode automatically to RECIRCULATION mode Automatic or Manual
      Foot/DEF Auto Mode ON Function to turn the airflow from FOOT/DEF ON automatically when AUTO MODE is ON ON or OFF
      Foot/DEF Automatic Blow Up Function ON Function to increase the blower level automatically when the defroster is ON ON or OFF
      Ambient Temperature Shift Normal Function to display shifted ambient temperature versus actual ambient temperature -3C, -2C, -1C, Normal, +1C, +2C, +3C
      Emission Gas Sensor Shift Normal Function to change the sensitivity of the exhaust gas sensor Much Less, Less, Little Less, Normal, Little More, More, Much More

    2. Customizing with the Multi-display (w/ Navigation System (for HDD))


      1. Turn the engine switch on (IG).

      2. Enter the following menus: SETUP / Vehicle / Vehicle customization / Climate setting.

      3. Select the setting by referring to the table below.

        Display Default Content Setting Relevant ECU
        Smog sensor sensitivity 0 Function to change the sensitivity of the exhaust gas sensor. -3, -2, -1, 0, +1, +2, +3 A/C Amplifier
        Auto A/C mode On Function to turn the A/C ON automatically by pressing the AUTO button when the blower is ON and the A/C is OFF. On or Off A/C Amplifier
        Efficient ventilation mode On In case of turning the A/C ON to cool the cabin down quickly, this is the function to change the mode automatically to RECIRCULATION mode On or Off A/C Amplifier

  12. POWER WINDOW CONTROL SYSTEM

    Power Window
    Tester Display Default Content Setting
    Door Key P/W Up OFF Function that raises all power windows when, with engine switch off, key in driver door key cylinder is turned to and held in lock position for more than 1.5 seconds ON/OFF
    Door Key P/W Down OFF Function that lowers all power windows when, with engine switch off, key in driver door key cylinder is turned to and held in unlock position for more than 1.5 seconds ON/OFF
    P/W Up W/ Transmit OFF Function that raises all power windows when, with engine switch off, lock switch on transmitter is pressed and held for more than 3.0 seconds ON/OFF
    P/W Down W/ Transmit OFF Function that lowers all power windows when, with engine switch off, unlock switch on transmitter is pressed and held for more than 3.0 seconds ON/OFF
    P/W Up W/ Smart OFF Function that raises all power windows when, with engine switch off, entry lock switch on driver side door outer handle is pressed and held for more than 3.0 seconds ON/OFF

  13. POWER SLIDE DOOR SYSTEM

    Rear Left Door or Rear Right Door (w/ Power Slide Door RH)
    Tester Display Default Content Setting
    PSD SW Operation 0.8 s Function to operate power slide door switch 0.8 s or ON
    PSD Buzzer ON Function to sound buzzer when power slide door is in operation ON or OFF
    Wireless PSD Operation 0.8 s Function to operate wireless power slide door switch 1 TIME, 2 TIMES, 0.8 s or OFF

  14. POWER BACK DOOR SYSTEM

    Power Back Door System
    Tester Display Default Content Setting
    PBD SW Operation 0.8 s Function that turns power back door closer switch on when switch is pushed once or held down for 0.8 sec. 0.8 s or ON
    PBD Buzzer ON This function makes the power back door buzzer sound when power back door is operating ON or OFF
    Wirelss PBD Operation

    1 Motion*1

    0.8s*2

    		 Function that operates power back door when transmitter switch is pressed in specified way 1 Motion*1, 1 Oper , 2 Oper , 0.8 s or OFF

    • *1: w/o Windshield Deicer System

    • *2: w/ Windshield Deicer System

  15. LIGHTING SYSTEM (EXT)

    Light Control
    Display Default Content Setting
    Response Time Normal Changes the delay timing of lighting the taillights when going into a tunnel when the light control switch is in the AUTO position. Long or Normal
    Sensitivity Normal Adjusts the sensitivity of the automatic light control system. Light2, Light1, Normal, Dark1 or Dark2
    Disp Ex OFF Sen Normal Changes the ambient brightness level to dim the lights such as the indicator lights of the combination meter, A/C indicator light and clock. Light2, Light1, Normal, Dark1 or Dark2
    Disp Ex ON Sen Normal Changes the ambient brightness level to dim the lights such as the indicator lights of the combination meter, A/C indicator light and clock. Light2, Light1, Normal, Dark1 or Dark2