BLACK OUT TAPE (for Front Door) REMOVAL

Tech Tips


  • Use the same procedure for the RH and LH sides.

  • The procedure listed below is for the LH side.

  • When removing the window frame moulding, black out tape and outside stripe, heat the vehicle body, window frame moulding, black out tape and outside stripe using a heat light.

    Standard
    Item Temperature
    Vehicle Body 40 to 60°C (104 to 140°F)
    Window Frame Moulding 20 to 30°C (68 to 86°F)
    Black Out Tape 20 to 30°C (68 to 86°F)
    Outside Stripe 20 to 30°C (68 to 86°F)

Note

Do not heat the vehicle body, window frame moulding, black out tape and outside stripe excessively.


  1. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

    Note


    • After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work Click here.

    • When disconnecting the cable, some systems need to be initialized after the cable is reconnected Click here.

  2. REMOVE FRONT DOOR LOWER FRAME BRACKET GARNISH LH


    1. A00K0GV

      Detach the 2 clips and remove the front door lower frame bracket garnish LH.

  3. REMOVE NO. 2 DOOR INSIDE HANDLE BEZEL LH


    1. A00JYBN

      Using a moulding remover, detach the 3 claws and remove the inside handle bezel as shown in the illustration.

  4. REMOVE ASSIST GRIP COVER LH


    1. A00JY4L

      Using moulding remover A, detach the 8 claws and remove the assist grip cover.

  5. REMOVE FRONT DOOR TRIM BOARD SUB-ASSEMBLY LH


    1. A00JZZF

      Remove the 3 screws.

    2. Remove the 12 clips.

    3. A00K22RE01
      Text in Illustration
      *1 Reference Boss

      Pull out the front door trim board sub-assembly in the direction indicated by the arrow in the illustration.

    4. Raise the front door trim board sub-assembly to detach the 4 claws and remove the front door trim board sub-assembly together with the front door inner glass weatherstrip LH.

    5. A00JZ5R

      Disconnect the 2 connectors.

    6. w/ Seat Position Memory System:


      1. A00JUOF

        Disconnect the connectors.

    7. A00JXET

      Disconnect the front door lock remote control cable assembly and front door inside locking cable assembly.

  6. REMOVE FRONT DOOR INNER GLASS WEATHERSTRIP LH


    1. A00JWX7

      Using a screwdriver, detach the 4 claws and remove the front door inner glass weatherstrip from the front door trim board sub-assembly as shown in the illustration.

  7. REMOVE FRONT DOOR SERVICE HOLE COVER LH


    1. A00K1TG

      Remove the bolt.

    2. Detach the 2 clamps, move the wire harness out of the way and remove the service hole cover.

      Tech Tips

      Remove any remaining butyl tape from the door.

  8. REMOVE OUTER REAR VIEW MIRROR ASSEMBLY LH

    A0094EB

    1. Disconnect the connector.

    2. Remove the 3 nuts.

    3. Detach the claw and remove the outer rear view mirror.

  9. REMOVE FRONT DOOR GLASS SUB-ASSEMBLY LH


    1. Connect the cable to the negative (-) battery terminal.

    2. Connect the power window regulator master switch assembly and move the front door glass sub-assembly so that the door glass bolts can be seen.

    3. Disconnect the cable from the negative (-) battery terminal and power window regulator master switch assembly.

      Note


      • After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work Click here.

      • When disconnecting the cable, some systems need to be initialized after the cable is reconnected Click here.

    4. A00K14P

      Remove the 2 bolts.

      Note

      After the bolts are removed, do not allow the door glass to fall.

    5. A00K1P3E01

      Remove the front door glass sub-assembly as indicated by the arrows in the order shown in the illustration.

      Note

      Do not damage the door glass.

  10. REMOVE FRONT DOOR GLASS RUN LH


    1. A00K0L3

      Remove the front door glass run.

  11. REMOVE FRONT DOOR BELT MOULDING LH

    A00JZPEE01
    Text in Illustration
    *1 Protective Tape

    1. Put protective tape around the belt moulding.

    2. Detach the 6 claws and remove the front door belt moulding.

  12. REMOVE FRONT DOOR WEATHERSTRIP LH

    A00JUC9

    1. Detach the 3 clips and remove the upper part of the front door weatherstrip so that the moulding can be removed.

  13. REMOVE FRONT DOOR REAR WINDOW FRAME MOULDING LH


    1. A00K1ZP

      Remove the door window frame moulding clip.

    2. A00K1CGE01

      Put protective tape around the front door rear window frame moulding.

    3. Using a moulding remover, detach the clip and remove the double-sided tape to remove the front door rear window frame moulding.

      Text in Illustration
      *1 Protective Tape
      *2 Double-sided Tape
      *3 Moulding Remover

  14. REMOVE NO. 1 BLACK OUT TAPE LH

    A00JUKP

    1. Pull back an edge of the black out tape and pull it parallel to the vehicle body to remove it.

  15. REMOVE FRONT DOOR OUTSIDE STRIPE LH

    A00JXXQ

    1. Pull back an edge of the front door outside stripe and pull it parallel to the vehicle body to remove it.

  16. REMOVE LOWER FRONT DOOR OUTSIDE STRIPE LH

    A00JZJN

    1. Pull back an edge of the lower front door outside stripe and pull it parallel to the vehicle body to remove it.