REAR DOOR WINDOW FRAME MOULDING INSTALLATION

Tech Tips


  • Use the same procedure for the RH and LH sides.

  • The procedure listed below is for the LH side.

  • When installing the window frame moulding, heat the vehicle body and window frame moulding using a heat light.

Standard
Item Temperature
Vehicle Body 40 to 60°C (104 to 140°F)
Window Frame Moulding 20 to 30°C (68 to 86°F)

Note

Do not heat the vehicle body or window frame moulding excessively.


  1. INSTALL REAR DOOR FRONT WINDOW FRAME MOULDING LH


    1. Clean the vehicle body surface.


      1. Using a heat light, heat the vehicle body surface.

      2. Remove the double-sided tape from the vehicle body surface.

      3. Wipe off any tape adhesive residue with cleaner.

    2. Install a new rear door front window frame moulding.


      1. Using a heat light, heat a new rear door front window frame moulding and the vehicle body surface.

      2. Remove the peeling paper from the face of the rear door front window frame moulding.

        Tech Tips

        After removing the peeling paper, keep the exposed adhesive free from foreign matter.

      3. Attach the clip and double-sided tape to install the rear door front window frame moulding.

        Tech Tips

        Press the rear door front window frame moulding firmly to install it.

    3. Install a new door window frame moulding clip.

  2. INSTALL REAR DOOR WEATHERSTRIP LH


    1. Attach the clip to install the upper part of the rear door weatherstrip.

  3. INSTALL REAR DOOR BELT MOULDING LH


    1. Attach the 7 claws to install the rear door belt moulding.

  4. INSTALL REAR DOOR GLASS SUB-ASSEMBLY LH


    1. Connect the cable to the negative (-) battery terminal and rear power window regulator motor connector.

    2. A00O8NO

      Connect the power window regulator switch assembly and move the arm of the regulator so that the roller on the arm can be seen through the service hole.

    3. Disconnect the power window regulator switch assembly and rear power window regulator motor connector.

    4. Disconnect the cable from the negative (-) battery terminal.

      Note


      • w/ Navigation System (for HDD):

        After the ignition switch is turned off, the HDD navigation system requires approximately a minute to record various types of memory and settings. As a result, after turning the ignition switch off, wait a minute or more before disconnecting the cable from the negative (-) battery terminal.

      • When disconnecting the cable, some systems need to be initialized after the cable is reconnected Click here.

    5. A00O9RJ

      Insert the rear door glass sub-assembly into the rear door panel along the rear door glass run as indicated by the arrow in the illustration.

  5. INSTALL REAR DOOR QUARTER WINDOW GLASS LH


    1. A00O7UA

      Install the rear door quarter window glass together with the rear door quarter window weatherstrip in the direction indicated by the arrow in the illustration.

  6. INSTALL REAR DOOR WINDOW DIVISION BAR SUB-ASSEMBLY LH


    1. Insert the rear door window division bar sub-assembly from above.

    2. Install the rear door window division bar sub-assembly to the glass run.

    3. Install the temporary bolt to the rear door window division bar sub-assembly.

    4. Install the rear door window division bar sub-assembly.

    5. Install the 2 bolts and screw.

    6. Tighten the temporary bolt to install the rear door window division bar sub-assembly.

  7. INSTALL REAR DOOR GLASS RUN LH


    1. Install the glass run.

  8. INSTALL REAR DOOR SERVICE HOLE COVER LH


    1. Apply new butyl tape to the rear door panel.

    2. A00O364E01
      Text in Illustration
      *1 Reference Point

      Pass the rear door lock remote control cable assembly and rear door inside locking cable assembly through a new rear door service hole cover.

    3. Attach the rear door service hole cover using to the reference points on the rear door panel.

      Note


      • There should be no wrinkles or folds after attaching the service hole cover.

      • After attaching the service hole cover, check the seal quality.

    4. Connect the connector.

    5. Attach the 2 clamps to the rear door wire.

  9. INSTALL REAR DOOR INNER GLASS WEATHERSTRIP LH


    1. A00O6BR

      Attach the 3 claws to install the rear door inner glass weatherstrip as shown in the illustration.

  10. INSTALL REAR DOOR TRIM BOARD SUB-ASSEMBLY LH


    1. A00O32D

      Install the clamp to the door panel.

    2. Connect the rear door lock remote control cable assembly and rear door inside locking cable assembly.

    3. Connect each connector.

    4. A00O5NC

      Attach the rear door trim board sub-assembly by attaching the 4 claws of the rear door inner glass weatherstrip as shown in the illustration.

    5. Attach the 9 clips and install the rear door trim board sub-assembly.

    6. Install the 3 screws.

  11. INSTALL ASSIST GRIP COVER LH


    1. A00OBDH

      Attach the 8 claws to install the assist grip cover.

  12. INSTALL NO. 2 DOOR INSIDE HANDLE BEZEL LH


    1. A00O3XZ

      Attach the 3 claws to install the door inside handle bezel.

  13. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

    Note

    When disconnecting the cable, some systems need to be initialized after the cable is reconnected Click here.