FRONT DOOR BELT MOULDING INSTALLATION

Tech Tips


  • Use the same procedure for the RH and LH sides.

  • The procedure listed below is for the LH side.


  1. INSTALL FRONT DOOR BELT MOULDING LH


    1. Attach the 6 claws to install the front door belt moulding.

  2. INSTALL FRONT DOOR GLASS RUN LH


    1. A00O7MY

      Install the front door glass run.

  3. INSTALL FRONT DOOR GLASS SUB-ASSEMBLY LH


    1. Connect the cable to the negative (-) battery terminal.

    2. Connect the power window regulator master switch assembly and move the front door glass sub-assembly so that the door glass bolt installation locations can be seen.

    3. Disconnect the cable from the negative (-) battery terminal and power window regulator master switch assembly.

      CAUTION:

      Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system Click here.

    4. A00O43XE01

      Insert the front door glass sub-assembly into the front door panel along the front door glass run as indicated by the arrows in the order shown in the illustration.

    5. A00O680E01

      Install the front door glass sub-assembly with the 2 bolts.

      Torque:
      5.5 N*m  { 56 kgf*cm, 49 in.*lbf }

      Tech Tips

      Tighten the bolts in the order shown in the illustration.

  4. INSTALL OUTER REAR VIEW MIRROR ASSEMBLY LH


    1. Attach the claw to install the outer rear view mirror, and then install the 3 nuts.

      Torque:
      8.0 N*m  { 82 kgf*cm, 71 in.*lbf }

    2. Connect the connector.

  5. INSTALL FRONT DOOR SERVICE HOLE COVER LH


    1. Apply new butyl tape to the front door panel.

    2. A00O89SE01
      Text in Illustration
      *1 Reference Point

      Pass the front door lock remote control cable assembly and front door inside locking cable assembly through a new front door service hole cover.

    3. Attach the front door service hole cover using the reference points on the front door panel.

      Note


      • There should be no wrinkles or folds after attaching the service hole cover.

      • After attaching the service hole cover, check the seal quality.

      Note

      Securely install the front door service hole cover preventing wrinkles and air bubbles.

    4. A00OAYR

      Attach the 2 clamps.

    5. Install the bolt to the front door wire.

  6. INSTALL FRONT DOOR INNER GLASS WEATHERSTRIP LH


    1. A00JWX7

      Using a screwdriver, detach the 4 claws and remove the front door inner glass weatherstrip from the front door trim board sub-assembly as shown in the illustration.

  7. INSTALL FRONT DOOR TRIM BOARD SUB-ASSEMBLY LH


    1. A00O9T6

      Connect the front door lock remote control cable assembly and front door inside locking cable assembly.

    2. Connect 2 connectors.

    3. w/ Seat Position Memory System:


      1. Connect the connectors.

    4. A00OB1V

      Attach the front door trim board sub-assembly by attaching the 4 claws of the front door inner glass weatherstrip as shown in the illustration.

    5. A00O4LI

      Attach the 12 clips and front door trim board retainer to install the front door trim board sub-assembly.

    6. Install the 3 screws.

  8. INSTALL ASSIST GRIP COVER LH


    1. A00O6EG

      Attach the 8 claws to install the assist grip cover.

  9. INSTALL NO. 2 DOOR INSIDE HANDLE BEZEL LH


    1. A00OB5L

      Attach the 3 claws to install the inside handle bezel.

  10. INSTALL FRONT DOOR LOWER FRAME BRACKET GARNISH LH


    1. Attach the 2 claws to install the front door lower frame bracket garnish.

  11. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

    Note

    When disconnecting the cable, some systems need to be initialized after the cable is reconnected Click here.

  12. ADJUST SIDE TELEVISION CAMERA ASSEMBLY (w/ Side Monitor System)


    1. w/ Rear View Monitor System:

      Adjust the side television camera Click here.

    2. w/ Parking Assist Monitor System:

      Adjust the side television camera Click here.