REAR CENTER SEAT OUTER BELT ASSEMBLY (for 60/40 Split Slide Walk-in Seat Type LH Side) INSTALLATION

CAUTION:

Wear protective gloves. Sharp areas on the parts may injure your hands.

Tech Tips


  • Use the same procedure for RHD and LHD vehicles.

  • The procedure listed below is for LHD vehicles.

  • A bolt without a torque specification is shown in the standard bolt chart Click here.


  1. INSTALL NO. 1 SEAT 3 POINT TYPE BELT ASSEMBLY LH

    A00JYVKE01
    Text in Illustration
    *1 Bolt
    *2 Nut

    Note

    When installing the retractor, make sure the claws of the vehicle (labeled "a" in the illustration) only contact the installation areas of the retractor.


    1. Align the claws with the seat belt positioning holes and install the retractor of the seat belt with the nut and bolt as shown in the illustration.

      Tech Tips

      First install the bolt, and then install the nut.

      Torque:
      for bolt
      7.5 N*m  { 76 kgf*cm, 66 in.*lbf }
      for nut
      42 N*m  { 428 kgf*cm, 31 ft.*lbf }

  2. INSTALL REAR SEAT SHOULDER BELT GUIDE


    1. Attach the guide and claw to install the belt guide.

  3. INSTALL SEATBACK COVER WITH PAD


    1. A00K1V8

      Connect the outer belt to the seatback cover with pad.

    2. A00JWVLE01
      Text in Illustration
      *1 Hog Ring Pliers
      *2 Hook
      *3 Hog Ring

      Attach the hooks.

    3. Using hog ring pliers, install the seatback cover with pad with new hog rings.

  4. INSTALL REAR NO. 1 SEAT HEADREST SUPPORT ASSEMBLY


    1. Attach the 4 claws to install the 2 supports.

  5. INSTALL REAR SEATBACK BOARD CARPET ASSEMBLY LH


    1. Attach the 7 clips to install the carpet.

  6. INSTALL REAR SEATBACK COVER


    1. Attach the 4 claws to install the cover.

  7. INSTALL REAR SEAT SHOULDER BELT COVER


    1. Connect the outer belt to the cover.

    2. A00JUBV

      Attach the 2 guides and 2 claws to install the cover.

  8. INSTALL SEAT BELT ANCHOR COVER CAP

    A00K0R2

    1. Attach the 2 claws to install the cap.

  9. INSTALL REAR SEAT LOCK CONTROL LEVER SUB-ASSEMBLY LH

    A00K0R2

    1. Attach the 2 claws to install the cap.

  10. INSTALL RECLINING ADJUSTER KNOB CAP LH

    A00K02F

    1. Attach the guide and claw to install the cap.

  11. INSTALL REAR NO. 1 SEAT INNER BELT ASSEMBLY LH

    A00JV8OE01
    Text in Illustration
    *a Protruding Part

    1. Install the inner belt and connect the 3 point type belt anchor with the bolt.

      Torque:
      42 N*m  { 428 kgf*cm, 31 ft.*lbf }

      Note

      Do not allow the anchor part of the anchor plate sub-assembly to overlap the protruding parts of the seatback frame.

  12. INSTALL CENTER SEATBACK ASSEMBLY


    1. Install the center seatback with the 2 bolts.

      Torque:
      21 N*m  { 214 kgf*cm, 15 ft.*lbf }

  13. INSTALL SEAT CUSHION COVER WITH PAD


    1. A00JVSR

      Attach the hook.

    2. A00K1AD

      Attach the hooks to install the seat cushion cover with pad.

  14. INSTALL REAR SEATBACK LOCK STRIKER COVER LH


    1. Attach the 3 clips to install the cover.

  15. INSTALL REAR SEAT CUSHION MOULDING LH

    A00JYK1

    1. Move the moulding in the direction of the arrow to attach the guide.

    2. Attach the 3 claws and clip to install the moulding.

  16. INSTALL CENTER SEAT HINGE COVER RH

    A00JZQ5

    1. Attach the 2 guides and install the cover with the clip.

  17. INSTALL RECLINING ADJUSTER RELEASE HANDLE LH


    1. Install the handle with the 3 screws.

  18. INSTALL REAR SEAT UPPER RECLINING COVER LH

    A00JV77

    1. Attach the 3 claws to install the cover.

  19. INSTALL REAR NO. 1 SEAT ASSEMBLY LH


    1. Install the rear No. 1 seat assembly LH Click here.