FRONT SEAT CUSHION HEATER (for Power Seat) INSTALLATION

CAUTION:

Wear protective gloves. Sharp areas on the parts may injure your hands.

Tech Tips


  • Use the same procedure for RHD and LHD vehicles.

  • The procedure listed below is for LHD vehicles.

  • Use the same procedure for the RH and LH sides.

  • The procedure listed below is for the LH side.


  1. INSTALL FRONT SEAT CUSHION HEATER ASSEMBLY LH

    A00O6AZE01
    Text in Illustration
    *1 Tack Pin
    *2 Seatback Cover
    *3 Seatback Heater
    *4 Name Stamp

    1. Set the seat cushion heater with the name stamp side facing the seat cushion cover.

    2. Install the seat cushion heater with new tack pins.

  2. INSTALL SEPARATE TYPE FRONT SEAT CUSHION COVER

    A00XHCIE01
    Text in Illustration
    *1 Hog Ring Pliers

    1. Using hog ring pliers, install the seat cushion cover to the seat cushion pad with new hog rings.

      Note


      • Be careful not to damage the cover.

      • When installing the hog rings, avoid wrinkling the cover.

  3. INSTALL SEAT CUSHION COVER WITH PAD


    1. Install the seat cushion cover with pad.

    2. for Front Passenger Side:

      Attach the claw to connect the connector.

    3. Attach the hooks.

    4. Connect the seat heater connector and attach the 3 wire harness clamps.

    5. Attach the 2 hooks.

    6. w/ Front Seat Side Airbag:


      1. Connect the airbag wire harness.

      2. Attach the fastening tape to close the cover.

    7. Connect the seat heater connector and attach the wire harness clamp.

    8. Install the rubber band to the seat cushion spring.

  4. INSTALL FRONT SEAT INNER BELT ASSEMBLY LH


    1. for Driver Side:

      Click here

    2. for Front Passenger Side:

      Click here

  5. INSTALL FRONT SEAT INNER CUSHION SHIELD LH

    A00XBYS

    1. Attach the 3 claws to install the cushion shield.

  6. INSTALL FRONT SEAT INNER CUSHION SHIELD RH (for Front Passenger Side)


    1. Attach the 4 claws to install the cushion shield.

  7. INSTALL LUMBAR SWITCH ASSEMBLY (for Driver Side)

    A009AMC

    1. Connect the lumbar switch connector.

    2. Attach the 2 claws to install the lumbar switch.

  8. INSTALL FRONT POWER SEAT SWITCH LH


    1. w/ Seat Memory System:

      Connect the 2 power seat switch connectors.

    2. w/o Seat Memory System:

      Connect the power seat switch connector.

    3. Install the power seat switch with 3 screws.

  9. INSTALL FRONT SEAT CUSHION SHIELD LH


    1. Attach the 3 wire harness clamps and connect the seat wire connector.

    2. Attach the 3 claws to close the wire harness cover.

    3. Remove the clip attached to the seat cushion spring and install it to the cushion shield.

      A00XC3S

    4. Attach the 2 clips, 3 claws and guide.

    5. Attach the guide of the front seat No. 1 inner cushion shield and install the screw.

    6. Connect the lifter motor connector.

  10. INSTALL RECLINING POWER SEAT SWITCH KNOB


    1. A00XJBW

      Attach the 2 claws to install the knob.

  11. INSTALL SLIDE AND VERTICAL POWER SEAT SWITCH KNOB

    A00XD3C

    1. Attach the 2 claws to install the knob.

  12. INSTALL FRONT SEAT ASSEMBLY


    1. Install the front seat assembly Click here.