FRONT SEAT CUSHION HEATER (for Power Seat) REMOVAL

CAUTION:

Wear protective gloves. Sharp areas on the parts may injure your hands.

Tech Tips


  • Use the same procedure for RHD and LHD vehicles.

  • The procedure listed below is for LHD vehicles.

  • Use the same procedure for the RH and LH sides.

  • The procedure listed below is for the LH side.


  1. REMOVE FRONT SEAT ASSEMBLY


    1. Remove the front seat assembly Click here.

  2. REMOVE SLIDE AND VERTICAL POWER SEAT SWITCH KNOB

    A00XDO4

    1. Using a moulding remover, detach the 2 claws and remove the knob.

  3. REMOVE RECLINING POWER SEAT SWITCH KNOB

    A00XHAC

    1. Using a moulding remover, detach the 2 claws and remove the knob.

  4. REMOVE FRONT SEAT CUSHION SHIELD LH


    1. Disconnect the lifter motor connector.

    2. Remove the screw of the front seat No. 1 inner cushion shield and detach the guide.

    3. Detach the clip of the front seat No. 1 inner cushion shield.

    4. Using a moulding remover, detach the 3 claws and guide.

    5. Move the cushion shield in the direction of the arrow to detach the clip and remove the front seat No. 1 inner cushion shield together with the cushion shield as a unit.

      A00XI83
    6. A00XJLJ

      Detach the 3 claws and open the wire harness cover.

    7. Detach the 3 wire harness clamps and disconnect the seat wire connector.

  5. REMOVE FRONT POWER SEAT SWITCH LH


    1. Remove the 3 screws.

    2. A00XFDW

      w/ Seat Memory System:

      Disconnect the 2 power seat switch connectors and remove the switch.

    3. A00XGWO

      w/o Seat Memory System:

      Disconnect the power seat switch connector and remove the switch.

  6. REMOVE LUMBAR SWITCH ASSEMBLY (for Driver Side)

    A009AX6

    1. Using a screwdriver, detach the 2 claws.

    2. Disconnect the lumbar switch connector and remove the lumbar switch.

  7. REMOVE FRONT SEAT INNER CUSHION SHIELD LH

    A00XH7M

    1. Using a moulding remover, detach the 3 claws and remove the cushion shield.

  8. REMOVE FRONT SEAT INNER CUSHION SHIELD RH (for Front Passenger Side)

    A00XK96

    1. Using a moulding remover, detach the 4 claws and remove the cushion shield.

  9. REMOVE FRONT SEAT INNER BELT ASSEMBLY LH


    1. for Driver Side:

      Click here

    2. for Front Passenger Side:

      Click here

  10. REMOVE SEAT CUSHION COVER WITH PAD


    1. A00OA3Q

      Remove the rubber band from the seat cushion spring.

    2. A00O7W0

      Disconnect the seat heater connector and detach the wire harness clamp.

    3. A00OABUE01
      Text in Illustration
      *1 Fastening Tape

      w/ Front Seat Side Airbag:


      1. Detach the fastening tape and open the cover.

      2. Disconnect the airbag wire harness.

    4. A00O8V6

      Detach the 2 hooks.

    5. A00O6CS

      Disconnect the seat heater connector and detach the 3 wire harness clamps.

    6. Detach the hooks.

      A00O36A
    7. A00O6KR

      for Front Passenger Side:

      Detach the claw and disconnect the connector.

    8. Remove the seat cushion cover with pad.

  11. REMOVE SEPARATE TYPE FRONT SEAT CUSHION COVER

    A00XEXU

    1. Remove the hog rings and seat cushion cover from the seat cushion pad.

  12. REMOVE FRONT SEAT CUSHION HEATER ASSEMBLY LH

    A00O7STE01
    Text in Illustration
    *1 Tack Pin

    1. Cut off the tack pins and remove the front seat cushion heater from the front seat cushion cover.