REAR NO. 2 SEAT ASSEMBLY (for Power Seat Type LH Side) INSTALLATION

CAUTION:

Wear protective gloves. Sharp areas on the parts may injure your hands.

Note


  • Under either of the following conditions, perform initialization (initial position memorization) of the fold seat control ECU Click here.


    • The fold seat control ECU is replaced with a new one.

    • Initialization (initial position reset) of the fold seat control ECU is performed.


  • Under any of the following conditions, perform initialization (initial position reset and initial position memorization) of the fold seat control ECU Click here.


    • The fold seat control ECU is exchanged with one from another vehicle.

    • The seatback frame and seat leg are inspected.

    • The seat is disassembled and the positions of the seatback and seat cushion change with respect to one another.

    • The seatback frame or seat leg is replaced.

    • The cable is disconnected from the battery while the seatback or seat cushion is operating.

Tech Tips


  • Use the same procedure for the RH and LH sides.

  • The procedure listed below is for the LH side.


  1. INSTALL REAR NO. 2 SEAT ASSEMBLY LH


    1. Place the rear No. 2 seat assembly in the cabin.

      Note

      Be careful not to damage the vehicle body.

      Tech Tips

      If installing the seat on the RH side with the LH side installed, install it with the No. 3 rear seat leg cover LH raised.

    2. Temporarily install the 4 bolts.

    3. Tighten the 4 bolts.

      Torque:
      37 N*m  { 377 kgf*cm, 27 ft.*lbf }
    4. A0098ERE01
      Text in Illustration
      *1 Guide

      Attach the 6 claws and 2 guides to close the 2 covers.

    5. Connect the connector.

  2. INSTALL NO. 1 DECK BOARD BRACKET LH


    1. Install the bracket with the 2 bolts.

  3. INSTALL DECK BOARD BRACKET REINFORCEMENT


    1. Attach the 2 hooks.

    2. Install the reinforcement with the 2 bolts.

  4. INSTALL REAR FLOOR MAT SUPPORT PLATE


    1. Attach the 5 clips and 2 guides.

    2. Attach the 4 claws to install the plate.

    3. Install the 3 bolts.

  5. INSTALL REAR NO. 3 FLOOR BOARD (w/o Rear Air Conditioning System)


    1. A009BRME01
      Text in Illustration
      *1 Guide

      Attach the 2 guides and 4 claws.

    2. Attach the clip to install the board.

  6. INSTALL REAR NO. 3 FLOOR BOARD (w/ Rear Air Conditioning System)


    1. A009B7RE01
      Text in Illustration
      *1 Guide

      Attach the 2 guides and 3 claws.

    2. Attach the clip to install the board.

  7. INSTALL REAR NO. 4 FLOOR BOARD


    1. A00950OE01
      Text in Illustration
      *1 Guide

      Attach the 2 guides and 3 claws.

    2. Attach the clip to install the board.

  8. INSTALL DECK BOARD ASSEMBLY


    1. Attach the 4 clips.

    2. Install the deck board with the 2 bolts.

  9. PERFORM INITIALIZATION

    Note


    • Under either of the following conditions, perform initialization (initial position memorization) of the fold seat control ECU Click here.


      • The fold seat control ECU is replaced with a new one.

      • Initialization (initial position reset) of the fold seat control ECU is performed.


    • Under any of the following conditions, perform initialization (initial position reset and initial position memorization) of the fold seat control ECU Click here.


      • The fold seat control ECU is exchanged with one from another vehicle.

      • The seatback frame and seat leg are inspected.

      • The seat is disassembled and the positions of the seatback and seat cushion change with respect to one another.

      • The seatback frame or seat leg is replaced.

      • The cable is disconnected from the battery while the seatback or seat cushion is operating.

  10. CHECK REAR NO. 2 SEAT


    1. Check the power seat operation Click here.