REAR NO. 2 SEAT ASSEMBLY (for Power Seat Type LH Side) DISASSEMBLY

CAUTION:

Wear protective gloves. Sharp areas on the parts may injure your hands.

Note


  • Under either of the following conditions, perform initialization (initial position memorization) of the fold seat control ECU Click here.


    • The fold seat control ECU is replaced with a new one.

    • Initialization (initial position reset) of the fold seat control ECU is performed.


  • Under any of the following conditions, perform initialization (initial position reset and initial position memorization) of the fold seat control ECU Click here.


    • The fold seat control ECU is exchanged with one from another vehicle.

    • The seatback frame and seat leg are inspected.

    • The seat is disassembled and the positions of the seatback and seat cushion change with respect to one another.

    • The seatback frame or seat leg is replaced.

    • The cable is disconnected from the battery while the seatback or seat cushion is operating.

Tech Tips


  • Use the same procedure for the RH and LH sides.

  • The procedure listed below is for the LH side.


  1. REMOVE CAP


    1. A00K0I8

      Remove the 2 caps.

  2. REMOVE REAR SEAT CUSHION LOWER HINGE COVER LH


    1. A00JW3G

      Remove the 2 screws.

    2. Detach the 3 claws and remove the cover.

  3. REMOVE REAR SEAT CUSHION LOWER HINGE COVER RH


    1. A00K20ZE01
      Text in Illustration
      *1 Guide

      Remove the 2 screws.

    2. Detach the 2 claws and guide and remove the cover.

  4. REMOVE REAR NO. 2 SEAT INNER BELT ASSEMBLY LH

    A0095OZ

    1. Using a T45 "TORX" socket wrench, remove the bolt and inner belt assembly.

  5. REMOVE FOLD SEAT CONTROL ECU


    1. A0095UI

      Disconnect the 2 connectors.

    2. Remove the 2 nuts and ECU.

  6. REMOVE REAR SEAT NO. 1 CUSHION MOULDING


    1. A00JY7NE01
      Text in Illustration
      *1 Guide

      Using a clip remover, remove the 2 clips.

    2. Detach the 2 claws and 4 guides and remove the moulding.

  7. REMOVE SEAT CUSHION COVER WITH PAD


    1. A00JYNQE01
      Text in Illustration
      *1 Fastener

      Open the 2 fasteners.

    2. A00K0KA

      Remove the 2 clips and open the under part of the seat cushion cover.

    3. A00JWSIE01
      Text in Illustration
      *1 Hook

      Detach the 2 hooks and remove the seat cushion cover with pad.

  8. REMOVE NO. 3 SEAT CUSHION COVER SUB-ASSEMBLY LH


    1. A00JUNBE01
      Text in Illustration
      *1 Fastener

      Detach the fastener.

    2. Remove the hog rings and seat cushion cover.

  9. REMOVE REAR SEAT CUSHION INNER EDGE PROTECTOR LH


    1. A00JYJDE01
      Text in Illustration
      *1 Tack Pin

      Cut off the tack pins and remove the protector from the cushion pad.

  10. REMOVE REAR SEAT NO. 2 CUSHION MOULDING


    1. A00JYP4

      Remove the 2 screws.

    2. Detach the 2 claws and remove the moulding.

  11. REMOVE REAR SEAT NO. 3 LEG COVER LH


    1. A00JW1P

      Detach the 2 claws and remove the cover.

  12. REMOVE REAR SEAT CUSHION INNER HINGE COVER LH


    1. A00JVWOE01
      Text in Illustration
      *1 Guide

      Remove the screw and clip.

    2. Detach the guide and remove the cover.

  13. REMOVE REAR SEAT CUSHION INNER HINGE COVER RH


    1. A00K1NVE01
      Text in Illustration
      *1 Guide

      Remove the screw and clip.

    2. Detach the guide and remove the cover.

  14. REMOVE LOWER SEAT TRACK RAIL LH


    1. A00JTYW

      Remove the 2 bolts and seat track rail.

  15. REMOVE REAR SEATBACK BOARD SUB-ASSEMBLY LH


    1. A00JZWQ

      Detach the 7 clips and remove the board.

  16. REMOVE REAR SEATBACK LOCK HOOK


    1. A00K19F

      Remove the lock hook.

  17. REMOVE REAR SEAT NO. 1 COVER BEZEL


    1. A00JVTDE01
      Text in Illustration
      *1 Guide

      Remove the 2 screws, detach the guide and remove the bezel.

  18. REMOVE SEATBACK COVER WITH PAD


    1. A00K0XRE01
      Text in Illustration
      *1 Hook

      Detach the hooks.

    2. A00JXWJ

      Detach the 8 clips and remove the seatback cover with pad.

  19. REMOVE NO. 3 SEATBACK COVER SUB-ASSEMBLY LH


    1. A00K194

      Remove the hog rings and seatback cover.

  20. REMOVE REAR NO. 2 SEATBACK EDGE PROTECTOR


    1. A00K08CE01
      Text in Illustration
      *1 Tack Pin

      Cut off the tack pins and remove the protector from the seatback pad.

  21. REMOVE NO. 2 SEATBACK COVER


    1. A00JY31

      Detach the 2 claws and remove the cover.

  22. REMOVE REAR SEAT HEADREST COVER


    1. A00JZDFE01
      Text in Illustration
      *1 Guide

      Remove the 2 screws.

    2. Detach the 2 claws and guide and remove the cover.

  23. REMOVE REAR SEAT HEADREST CABLE


    1. A00JTYGE01
      Text in Illustration
      *1 Cable End
      *2 Clamp

      Detach the 2 clamps.

    2. Twist the 2 cable ends in the direction indicated by the arrow and remove the cable.

  24. REMOVE REAR SEAT HEADREST ASSEMBLY


    1. A00JVKZ

      Remove the 3 nuts and headrest.

  25. REMOVE REAR SEATBACK EDGE PROTECTOR


    1. A00JVCE

      Detach the 4 claws and remove the 2 protectors.

  26. REMOVE REAR NO. 3 SEAT INNER RECLINING COVER LH


    1. A00K1C1

      Detach the 4 claws and remove the cover.

  27. REMOVE REAR NO. 3 SEAT OUTER RECLINING COVER LH


    1. A00JZY1E01
      Text in Illustration
      *1 Guide

      Remove the screw.

    2. Detach the guide and 2 claws and remove the cover.

  28. REMOVE NO. 2 SEAT CUSHION FRAME SUB-ASSEMBLY LH


    1. A00JVY2

      Remove the bolt and disconnect the wire harness.

    2. A00JZ0E

      Using a screwdriver, release the lock lever as shown in the illustration.

    3. A00JVA3

      Retract the seat cushion frame.

    4. Using a T40 "TORX" socket wrench, remove the 4 "TORX" bolts and seat cushion frame.

  29. REMOVE REAR SEAT LEG COVER LH


    1. A00K0ANE01
      Text in Illustration
      *1 Hook

      Remove the clip.

    2. Detach the 3 hooks and 5 clips and remove the cover.

  30. REMOVE 3RD SEAT LINK SUB-ASSEMBLY LH


    1. A00JYZTE01
      Text in Illustration
      *1 Guide

      Remove the 3 clips.

    2. Detach the 2 claws and 4 guides and remove the 3rd seat link.

  31. REMOVE REAR NO. 2 SEAT INNER RECLINING COVER LH


    1. A00JTQ0

      Detach the 5 claws and remove the cover.

  32. REMOVE REAR NO. 2 SEAT OUTER RECLINING COVER LH


    1. A00JZ2VE01
      Text in Illustration
      *1 Guide

      Remove the screw.

    2. Detach the guide and 2 claws and remove the cover.

  33. REMOVE REAR SEAT LOCK RELEASE STRAP ASSEMBLY LH


    1. A00JVY8E01
      Text in Illustration
      *1 Clamp
      *2 Cable End

      Detach the 2 clamps.

    2. Twist the cable end in the direction indicated by the arrow and remove the cable.

  34. REMOVE REAR SEAT LOCK RELEASE STRAP ASSEMBLY RH (for RH Side)


    1. A00JUEEE01
      Text in Illustration
      *1 Cable Tie
      *2 Clamp
      *3 Cable End

      Cut off the 2 cable ties and detach the 3 clamps.

    2. Twist the cable end in the direction indicated by the arrow and remove the cable.

  35. REMOVE REAR SEAT LOCK CONTROL CABLE LH


    1. A00K0L1E01
      Text in Illustration
      *1 Cable End
      *2 Clamp

      Detach the 2 clamps.

    2. Twist the 2 cable ends in the direction indicated by the arrow and remove the cable.

  36. REMOVE REAR SEAT LOCK CONTROL CABLE RH (for RH Side)


    1. A00JX0EE01
      Text in Illustration
      *1 Cable Tie
      *2 Clamp
      *3 Cable End

      Cut off the 2 cable ties and detach the 3 clamps.

    2. Twist the 2 cable ends in the direction indicated by the arrow and remove the cable.

  37. REMOVE NO. 3 SEATBACK FRAME SUB-ASSEMBLY LH


    1. A00JVKJ

      Using a T45 "TORX" socket wrench, remove the 4 "TORX" bolts and frame.

  38. REMOVE REAR NO. 2 SEAT WIRE LH


    1. A00JZ90

      Disconnect the connector.

    2. Detach the wire harness clamps and remove the seat wire.

  39. REMOVE NO. 3 SEAT LEG ASSEMBLY LH


    1. A00JZFV

      Remove the 4 clips and seat cushion under carpet LH from the No. 3 seat leg.

  40. REMOVE NO. 2 SEAT LEG ASSEMBLY (for RH Side)


    1. A00JVRE

      Remove the 4 clips and seat cushion under carpet RH from the No. 2 seat leg.