REAR NO. 1 SEAT ASSEMBLY (for 60/40 Split Slide Walk-in Seat Type RH Side) REASSEMBLY

CAUTION:

Wear protective gloves. Sharp areas on the parts may injure your hands.

Tech Tips


  • Use the same procedure for RHD and LHD vehicles.

  • The procedure listed below is for LHD vehicles.

  • A bolt without a torque specification is shown in the standard bolt chart Click here.


  1. INSTALL REAR SEAT TRACK ADJUSTING HANDLE RH


    1. A009883

      Install the handle.

      Tech Tips

      Make sure the handle is straight when installing it, and check that it is centered.

    2. A00983J

      Install the seat cushion side frame.

  2. INSTALL REAR SEAT CUSHION FRAME SUB-ASSEMBLY RH


    1. Install the seat cushion frame and seat leg plate with the 6 nuts.

      Torque:
      32 N*m  { 326 kgf*cm, 24 ft.*lbf }

  3. INSTALL REAR SEAT CUSHION SPRING


    1. Attach the 2 hooks to install the spring.

  4. INSTALL REAR SEAT COVER


    1. Install the cover with the screw.

  5. INSTALL REAR SEATBACK FRAME SUB-ASSEMBLY RH


    1. Temporarily install the seatback frame with the 4 "TORX" bolts.

    2. Using a T45 "TORX" socket wrench, tighten the 4 "TORX" bolts.

      Torque:
      29 N*m  { 296 kgf*cm, 21 ft.*lbf }

  6. INSTALL REAR SEATBACK LOCK PLATE LH


    1. Install the lock plate with the nut.

      Torque:
      18 N*m  { 184 kgf*cm, 13 ft.*lbf }

    2. Attach the 2 cable clamps and connect the cable.

  7. INSTALL REAR SEAT CUSHION SET PLATE


    1. Install the set plate with the 2 nuts.

      Torque:
      18 N*m  { 184 kgf*cm, 13 ft.*lbf }

  8. INSTALL REAR NO. 2 SEAT RECLINING CONTROL CABLE


    1. Install the cable.

    2. Attach the cable clamp and connect the cable.

  9. INSTALL REAR SEAT RECLINING CONTROL CABLE


    1. Install the cable.

    2. Attach the 2 cable clamps and connect the cable.

    3. Install 3 new cable ties.

  10. INSTALL REAR SEAT CUSHION SPRING DAMPER


    1. Install the damper with the 2 nuts.

  11. INSTALL RECLINING ADJUSTER INSIDE COVER RH


    1. Attach the claw and guide to install the cover.

  12. INSTALL RECLINING ADJUSTER INSIDE COVER RH

    A009B77

    1. Move the cover in the direction of the arrow to attach the 2 claws.

    2. Attach the clip to install the cover.

  13. INSTALL RECLINING ADJUSTER INSIDE COVER RH


    1. Attach the 2 claws to install the cover.

    2. Install the 2 screws.

  14. INSTALL REAR SEAT INNER RECLINING COVER RH


    1. Attach the guide and install the cover with the 2 screws.

  15. INSTALL REAR SEATBACK EDGE PROTECTOR


    1. Install the protector to the seatback frame.

  16. INSTALL SEPARATE TYPE REAR SEATBACK COVER

    A0095GTE01
    Text in Illustration
    *1 Hog Ring Pliers

    1. Using hog ring pliers, install the seatback cover to the seatback pad with new hog rings.

      Note


      • Be careful not to damage the cover.

      • When installing the hog rings, avoid wrinkling the cover.

  17. INSTALL SEATBACK COVER WITH PAD

    A009A96E01
    Text in Illustration
    *1 Hog Ring Pliers
    *2 Hook
    *3 Hog Ring

    1. Attach the hooks.

    2. Using hog ring pliers, install the seatback cover with pad with new hog rings.

  18. INSTALL REAR NO. 1 SEAT HEADREST SUPPORT ASSEMBLY


    1. Attach the 4 claws to install the 2 supports.

  19. INSTALL REAR SEATBACK BOARD CARPET ASSEMBLY RH


    1. Attach the 7 clips to install the carpet.

  20. INSTALL REAR SEATBACK COVER


    1. Attach the 4 claws to install the cover.

  21. INSTALL REAR CENTER BACK LOCK CONTROL LEVER

    A0097M7

    1. Attach the cable clamp to connect the cable to the lever.

    2. Move the lever in the direction of the arrow to attach the guide.

    3. Install the lever with the 2 screws.

  22. INSTALL REAR SEAT COVER CAP


    1. Attach the guide and claw to install the cap.

  23. INSTALL REAR SEAT LOCK CONTROL LEVER SUB-ASSEMBLY RH

    A0096QUE02

    1. Connect the cable in the order shown in the illustration to install the lever.

    2. Install the 2 screws.

  24. INSTALL RECLINING ADJUSTER KNOB CAP RH

    A00974Z

    1. Attach the guide and claw to install the cap.

  25. INSTALL SEPARATE TYPE REAR SEAT CUSHION COVER

    A00956FE01
    Text in Illustration
    *1 Hog Ring Pliers

    1. Using hog ring pliers, install the seat cushion cover to the seat cushion pad with new hog rings.

      Note


      • Be careful not to damage the cover.

      • When installing the hog rings, avoid wrinkling the cover.

  26. INSTALL REAR SEAT CUSHION EDGE PROTECTOR


    1. Install the protector to the cushion spring.

  27. INSTALL REAR NO. 2 SEAT PROTECTOR


    1. Install the 2 protectors to the cushion pad.

  28. INSTALL SEAT CUSHION COVER WITH PAD

    A009BBA

    1. Attach the hooks to install the seat cushion cover with pad.

  29. INSTALL REAR SEATBACK LOCK STRIKER COVER RH


    1. Attach the 3 clips to install the cover.

  30. INSTALL REAR SEAT INNER BELT ASSEMBLY


    1. Install the inner belt with the nut.

      Torque:
      42 N*m  { 428 kgf*cm, 31 ft.*lbf }

  31. INSTALL REAR NO. 1 SEAT INNER BELT ASSEMBLY RH

    A0095C5E01
    Text in Illustration
    *a Protruding Part

    1. Install the inner belt with the bolt.

      Torque:
      42 N*m  { 428 kgf*cm, 31 ft.*lbf }

      Note

      Do not allow the anchor part of the front seat inner belt assembly to overlap the protruding part of the front seat adjuster.

  32. INSTALL REAR SEAT REAR CUSHION MOULDING LH


    1. Attach the guide and 3 claws to install the moulding.

    2. Install the screw.

  33. INSTALL REAR SEAT CUSHION MOULDING RH

    A0094XC

    1. Move the moulding in the direction of the arrow to attach the guide and install the moulding.

    2. Attach the 3 claws and clip to install the moulding.

  34. INSTALL RECLINING ADJUSTER RELEASE HANDLE RH


    1. Install the handle with the 3 screws.

  35. INSTALL REAR SEAT UPPER RECLINING COVER RH

    A009A1O

    1. Attach the 3 claws to install the cover.