REAR AIRBAG SENSOR (for 3 Door) INSTALLATION

Tech Tips


  • Use the same procedure for the RH and LH sides.

  • The procedure listed below is for the LH side.


  1. INSTALL REAR AIRBAG SENSOR LH


    1. Turn the ignition switch off.

    2. Disconnect the cable from the negative (-) battery terminal.

      CAUTION:

      Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

      Note


      • w/ Navigation System (for HDD):

        After the ignition switch is turned off, the HDD navigation system requires approximately a minute to record various types of memory and settings. As a result, after turning the ignition switch off, wait a minute or more before disconnecting the cable from the negative (-) battery terminal.

      • When disconnecting the cable, some systems need to be initialized after the cable is reconnected Click here.

    3. Install the rear airbag sensor with the nut.

      Torque:
      9.0 N*m  { 92 kgf*cm, 80 in.*lbf }

      Note


      • If the rear airbag sensor has been dropped, or there are any cracks, dents or other defects in the case, bracket or connector, replace it with a new one.

      • When installing the rear airbag sensor, be careful that the SRS wiring does not interfere with other parts and that it is not pinched between other parts.

    4. Check that the rear airbag sensor is not loose.

    5. Connect the connector.

  2. INSTALL DECK TRIM SIDE PANEL ASSEMBLY LH


    1. Attach the 9 claws and 11 clips to install the deck trim side panel.

    2. Install the 3 bolts and 2 screws.

    3. Install the rear No. 1 seat outer belt floor anchor with the bolt.

      Torque:
      42 N*m  { 428 kgf*cm, 31 ft.*lbf }

    4. Install the front seat outer belt floor anchor with the bolt.

      Torque:
      42 N*m  { 428 kgf*cm, 31 ft.*lbf }

  3. INSTALL OUTER LAP BELT COVER

    Tech Tips

    Use the same procedure for the other outer lap belt anchor cover.


    1. Attach the 3 claws to install the outer lap belt anchor cover.

  4. INSTALL FRONT DECK SIDE TRIM COVER (w/ Tonneau Cover)

    Tech Tips

    Use the same procedure for the other front deck side trim cover.


    1. Attach the 2 claws to install the front deck side trim cover.

  5. INSTALL NO. 1 TONNEAU COVER HOLDER CAP (w/o Tonneau Cover)

    Tech Tips

    Use the same procedure for the other tonneau cover holder cap.


    1. Attach the 2 claws to install the tonneau cover holder cap.

  6. INSTALL NO. 1 LUGGAGE COMPARTMENT TRIM HOOK

    Tech Tips

    Use the same procedure for the other No. 1 luggage compartment trim hook.


    1. Install the No. 1 luggage compartment trim hook so that it is positioned horizontally.

  7. INSTALL REAR FLOOR CARPET ASSEMBLY


    1. Install the rear floor carpet.

  8. INSTALL QUARTER TRIM COVER HOLE LH


    1. Attach the 6 claws and 2 guides to install the quarter trim pocket tray.

  9. INSTALL REAR FLOOR MAT REAR SUPPORT PLATE


    1. Attach the 6 claws to install the rear floor mat rear support plate.

    2. Install the 5 screws.

  10. INSTALL MAT SET PLATE COVER

    Tech Tips

    Use the same procedure for all mat set plate covers.


    1. Attach the 2 claws to install the mat set plate cover.

  11. INSTALL TONNEAU COVER ASSEMBLY (w/ Tonneau Cover)


    1. Install the tonneau cover.

  12. INSTALL FRONT DOOR OPENING TRIM WEATHERSTRIP LH

    A00JTMZE01
    Text in Illustration
    *1 Paint Mark
    *2 Mark Position

    1. Align the paint mark on the front door opening trim weatherstrip with the mark position on the vehicle and install the front door opening trim weatherstrip as shown in the illustration.

  13. INSTALL DOOR SCUFF PLATE ASSEMBLY LH


    1. Attach the 4 clips, 10 claws and 2 guides to install the door scuff plate.

  14. INSTALL REAR NO. 1 SEAT ASSEMBLY


    1. for 60/40 Split Double-folding Seat Type LH Side:


      1. Install the rear No. 1 seat assembly Click here.

    2. for 60/40 Split Double-folding Seat Type RH Side:


      1. Install the rear No. 1 seat assembly Click here.

    3. for 60/40 Split Tumble Seat Type LH Side:


      1. Install the rear No. 1 seat assembly Click here.

    4. for 60/40 Split Tumble Seat Type RH Side:


      1. Install the rear No. 1 seat assembly Click here.

    5. for 60/40 Split Slide Walk-in Seat Type LH Side:


      1. Install the rear No. 1 seat assembly Click here.

    6. for 60/40 Split Slide Walk-in Seat Type RH Side:


      1. Install the rear No. 1 seat assembly Click here.

  15. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

    CAUTION:

    When disconnecting the cable, some systems need to be initialized after the cable is reconnected Click here.

  16. CHECK SRS WARNING LIGHT


    1. Check the SRS warning light Click here.