FRONT PASSENGER AIRBAG ASSEMBLY DISPOSAL

CAUTION:

Before performing pre-disposal deployment of any SRS part, review and closely follow all applicable environmental and hazardous material regulations. Pre-disposal deployment may be considered hazardous material treatment.


  1. PRECAUTION

    Tech Tips

    When scrapping a vehicle equipped with an SRS or disposing of the instrument panel passenger airbag, be sure to deploy the airbag first in accordance with the procedure described below. If any abnormality occurs with the airbag deployment, contact the service department of the distributor.

    CAUTION:


    • Never dispose of an instrument panel passenger airbag that has an unactivated airbag.

    • The airbag produces an exploding sound when it is deployed, so perform the operation outdoors and where it will not create a nuisance to nearby residents.

    • When deploying the airbag, always use the specified SST (SRS Airbag Deployment Tool). Perform the operation in a place away from electrical noise.

    • When deploying the airbag, perform the operation at least 10 m (32.8 ft.) away from the instrument panel passenger airbag.

    • The instrument panel passenger airbag becomes extremely hot when the airbag is deployed, so do not touch it for at least 30 minutes after deployment.

    • Use gloves and safety glasses when handling an instrument panel passenger airbag with a deployed airbag.

    • Do not apply water, etc. to an instrument panel passenger airbag with a deployed airbag.

    • Always wash your hands with water after completing the operation.

    • An airbag or pretensioner may be activated by static electricity. To prevent this, be sure to touch a metal surface with bare hands to discharge static electricity before performing this procedure.

  2. DISPOSE OF INSTRUMENT PANEL PASSENGER AIRBAG ASSEMBLY (WHEN INSTALLED IN VEHICLE)

    Tech Tips

    Prepare a battery as the power source to deploy the airbag.


    1. A0094VHE15

      Check the function of SST Click here.

    2. Read the precaution Click here.

    3. Disconnect the cable from the negative (-) battery terminal.

      CAUTION:

      Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

      Note


      • w/ Navigation System (for HDD):

        After the ignition switch is turned off, the HDD navigation system requires approximately a minute to record various types of memory and settings. As a result, after turning the ignition switch off, wait a minute or more before disconnecting the cable from the negative (-) battery terminal.

      • When disconnecting the cable, some systems need to be initialized after the cable is reconnected Click here.

    4. Remove the instrument panel passenger airbag Click here.

    5. A00954LE01

      Install SST.


      1. Disconnect the connector.

        Note

        When handling the airbag connector, take care not to damage the airbag wire harness.

      2. Connect SST connector to the instrument panel wire.

        SST
        09082-00700
        09082-00780

        Note

        To avoid damaging SST connector and wire harness, do not lock the secondary lock of the twin lock.

      3. Install the instrument panel passenger airbag Click here.

      4. A0099A3E26
        Text in Illustration
        *1 Battery
        *a 10 m or more

        Move SST at least 10 m (32.8 ft.) away from the vehicle front side window.

      5. Maintaining enough clearance for SST wire harness in the front side window, close all doors and windows of the vehicle.

        Note

        Take care not to damage SST wire harness.

      6. Connect the red clip of SST to the positive (+) battery terminal and the black clip of SST to the negative (-) battery terminal.

    6. Deploy the airbag.


      1. Check that no one is inside the vehicle or within a 10 m (32.8 ft.) radius of the vehicle.

      2. Press SST activation switch to deploy the airbag.

        CAUTION:


        • When deploying the airbag, make sure that no one is near the vehicle.

        • The instrument panel passenger airbag becomes extremely hot when the airbag is deployed, so do not touch it for at least 30 minutes after deployment.

        • Use gloves and safety glasses when handling an instrument panel passenger airbag with a deployed airbag.

        • Do not apply water to an instrument panel passenger airbag with a deployed airbag.

        • Always wash your hands with water after completing the operation.

        Tech Tips

        The airbag is deployed as the LED of SST activation switch comes on.

  3. DISPOSE OF INSTRUMENT PANEL PASSENGER AIRBAG ASSEMBLY (WHEN NOT INSTALLED IN VEHICLE)

    Note

    Be sure to follow the procedure detailed below when deploying the airbag.

    Tech Tips

    Prepare a battery as the power source to deploy the airbag.


    1. A0094VHE15

      Check the function of SST Click here.

    2. Remove the instrument panel passenger airbag Click here.

      CAUTION:


      • When removing the instrument panel passenger airbag, wait at least 90 seconds after the ignition switch is turned off and the cable is disconnected from the negative (-) battery terminal before starting work.

      • When storing the instrument panel passenger airbag, keep the airbag deployment side facing upward.

    3. A0099KHE01

      After connecting SST to each other, connect them to the instrument panel passenger airbag.

      SST
      09082-00802   ( 09082-10801, 09082-30801 )
    4. A009A8WE29
      Text in Illustration
      *a Wire Harness Diameter
      *b Stripped Wire Harness Section

      Using a service-purpose wire harness for the vehicle, tie the instrument panel passenger airbag to a tire.

      Cross-sectional area of stripped wire harness section
      1.25 mm2 (0.00192 in.2) or more

      CAUTION:

      If the wire harness is too thin or an alternative object is used to tie the instrument panel passenger airbag, it may be snapped by the shock when the airbag is deployed. Always use a wire harness for vehicle use with a cross-sectional area of at least 1.25 mm2(0.00192 in.2).

      Tech Tips

      To calculate the cross-sectional area of the stripped wire harness section: Cross-sectional area = 3.14 x (Diameter)2/ 4


      1. Position the instrument panel passenger airbag inside a tire with the airbag deployment side facing inside.

        A009BDGE02
        Text in Illustration
        *a Width *b Inner Diameter
        Tire size
        Must exceed the following dimensions
        Width
        185 mm (7.28 in.)
        Inner diameter
        360 mm (14.2 in.)

      2. Tie the instrument panel passenger airbag to the tire with several wire harnesses.

        CAUTION:


        • Make sure that the wire harnesses are tight. If there is slack in the wire harnesses, the instrument panel passenger airbag may become loose due to the shock when the airbag is deployed.

        • Always tie the instrument panel passenger airbag with the airbag deployment side facing inside.

        Note

        As the tire may be damaged by the airbag deployment, use a tire that you are planning to throw away.

    5. A0098DDE03

      Place tires.

      Text in Illustration
      *1

      Tire

      (2 or more)

      1. Place at least 2 tires under the tire which the instrument panel passenger airbag is tied to.

      2. Place at least 2 tires over the tire which the instrument panel passenger airbag is tied to. The top tire should have a disc wheel installed.

        Note


        • Do not place SST connector under the tires because it could be damaged.

        • As the disc wheel may be damaged by the airbag deployment, use a disc wheel that you are planning to throw away.

        • As the tires may be damaged by the airbag deployment, use tires that you are planning to throw away.

      3. A0099Q0

        Tie the tires together with 2 wire harnesses.

        CAUTION:

        Make sure that the wire harnesses are tight. Looseness in the wire harnesses results in the tires coming free due to the shock when the airbag is deployed.

    6. A0094HQE06
      Text in Illustration
      *1 Instrument Panel Passenger Airbag
      *2 Battery
      *a 10 m or more

      Connect SST connector.

      SST
      09082-00700

      Note

      To avoid damaging SST connector and wire harness, do not lock the secondary lock of the twin lock. Also, secure some slack for SST wire harness inside the tires.

    7. Deploy the airbag.


      1. Connect the red clip of SST to the positive (+) battery terminal and the black clip of SST to the negative (-) battery terminal.

      2. Check that no one is within a 10 m (32.8 ft.) radius of the tire which the instrument panel passenger airbag is tied to.

      3. Press SST activation switch to deploy the airbag.

        CAUTION:

        When deploying the airbag, make sure that no one is near the tires.

        Tech Tips

        The airbag is deployed as the LED of SST activation switch comes on.

    8. A009B67E07

      Dispose of the instrument panel passenger airbag.

      CAUTION:


      • The instrument panel passenger airbag becomes extremely hot when the airbag is deployed, so do not touch it for at least 30 minutes after deployment.

      • Use gloves and safety glasses when handling an instrument panel passenger airbag with a deployed airbag.

      • Do not apply water to an instrument panel passenger airbag with a deployed airbag.

      • Always wash your hands with water after completing the operation.


      1. Remove the instrument panel passenger airbag from the tire.

      2. Place the instrument panel passenger airbag in a plastic bag, tie it tightly and dispose of it in the same way as other general parts.