METER / GAUGE SYSTEM, Diagnostic DTC:B1501

DTC Code DTC Name
B1501 Sub Fuel Sender Open Detected

DESCRIPTION

Tech Tips

Trouble code B1501 is only stored in vehicles equipped with a double tank.

This DTC is stored when the combination meter detects a fuel sender gauge malfunction.

DTC Code DTC Detection Condition Trouble Area
B1501 The combination meter detects a fuel sender gauge malfunction.

  • Harness or connector

  • Combination meter assembly

  • Fuel sender gauge assembly

WIRING DIAGRAM

A00KYM6E03

INSPECTION PROCEDURE

PROCEDURE


  1. READ VALUE USING INTELLIGENT TESTER (FUEL SENDER GAUGE)


    1. Operate the intelligent tester according to the display and select the Data List Click here.

      Combination Meter
      Tester Display Measurement Item/Range Normal Condition Diagnostic Note
      Fuel Input Fuel sender gauge (main) input signal/Min.: 0, Max.: 127.5 Fuel sender input value Unit: L
      OK
      Fuel amount value displayed on the intelligent tester is almost same as needle indication.

    NG

    REPLACE COMBINATION METER ASSEMBLY Click here

    OK

  2. CHECK HARNESS AND CONNECTOR (COMBINATION METER - FUEL TANK VENT TUBE ASSEMBLY)


    1. Disconnect the G6 meter connector.

    2. Disconnect the t1 gauge connector.

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      G6-8 (L) - t1-4 (S) Always Below 1 Ω
      G6-23 (FE) - t1-5 (E)
      G6-21 (E2) - Body ground
      G6-8 (L) or t1-4 (S) - Body ground Always 10 kΩ or higher

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

    OK

  3. INSPECT FUEL TANK VENT TUBE ASSEMBLY

    A00KUXNE01
    Text in Illustration
    *a Fuel Tank Vent Tube Assembly
    *b

    Component without harness connected

    (Fuel Tank Vent Tube Assembly)

    1. Remove the fuel tank vent tube assembly.

      for 1GR-FE: Click here

      for 2TR-FE: Click here

      for 1KD-FTV: Click here

      for 5L-E: Click here

    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      4 (S) - 1 Always Below 1 Ω
      5 (E) - 2 Always Below 1 Ω
      Result
      Result Proceed to
      OK A
      NG (for 1GR-FE) B
      NG (for 2TR-FE) C
      NG (for 1KD-FTV) D
      NG (for 5L-E) E

    B

    REPLACE FUEL TANK VENT TUBE ASSEMBLY Click here

    C

    REPLACE FUEL TANK VENT TUBE ASSEMBLY Click here

    D

    REPLACE FUEL TANK VENT TUBE ASSEMBLY Click here

    E

    REPLACE FUEL TANK VENT TUBE ASSEMBLY Click here

    A

  4. INSPECT FUEL SENDER GAUGE ASSEMBLY


    1. Remove the fuel sender gauge assembly.

      for 1GR-FE: Click here

      for 2TR-FE: Click here

      for 1KD-FTV: Click here

      for 5L-E: Click here

    2. A00KZKVE02
      Text in Illustration
      *a Fuel Sender Gauge Assembly
      *b Float Level is F (Upper)
      *c Float Level is E (Lower)

      Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      1 - 2 Float level is F (upper) 12 to 18 Ω
      Float level is E (lower) 405 to 415 Ω
      Result
      Result Proceed to
      OK A
      NG (for 1GR-FE) B
      NG (for 2TR-FE) C
      NG (for 1KD-FTV) D
      NG (for 5L-E) E

    B

    REPLACE FUEL SENDER GAUGE ASSEMBLY Click here

    C

    REPLACE FUEL SENDER GAUGE ASSEMBLY Click here

    D

    REPLACE FUEL SENDER GAUGE ASSEMBLY Click here

    E

    REPLACE FUEL SENDER GAUGE ASSEMBLY Click here

    A

    REPLACE COMBINATION METER ASSEMBLY Click here