DOOR CONTROL RECEIVER (for 3 Door) REMOVAL


  1. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

    Note


    • After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work Click here.

    • When disconnecting the cable, some systems need to be initialized after the cable is reconnected Click here.

  2. REMOVE REAR NO. 1 SEAT ASSEMBLY (w/ Rear No. 1 Seat)


    1. for LH Side:

      Remove the rear No. 1 seat assembly Click here.

    2. for RH Side:

      Remove the rear No. 1 seat assembly Click here.

  3. REMOVE TONNEAU COVER ASSEMBLY (w/ Tonneau Cover)


    1. Remove the tonneau cover.

  4. REMOVE MAT SET PLATE COVER

    A00XIQKE01
    Text in Illustration
    *1 Protective tape

    Tech Tips

    Use the same procedure for all mat set plate covers.


    1. Using a screwdriver, detach the 2 claws and remove the mat set plate cover.

      Tech Tips

      Tape the screwdriver tip before use.

  5. REMOVE REAR FLOOR MAT REAR SUPPORT PLATE

    A00XEVE

    1. Remove the 5 screws.

    2. Detach the 6 claws and remove the rear floor mat rear support plate.

  6. REMOVE QUARTER TRIM COVER HOLE LH

    A00XH9N

    1. Detach the 2 claws and 2 guides and remove the quarter trim cover hole.

  7. REMOVE REAR FLOOR CARPET ASSEMBLY

    A00XJM4

    1. Remove the rear floor carpet.

  8. REMOVE NO. 1 LUGGAGE COMPARTMENT TRIM HOOK

    A00XHK8

    Tech Tips

    Use the same procedure for the other No. 1 luggage compartment trim hook.


    1. Remove the luggage compartment trim hook by turning it clockwise.

  9. REMOVE NO. 1 TONNEAU COVER HOLDER CAP (w/o Tonneau Cover)

    A00XJXZE01
    Text in Illustration
    *1 Protective tape

    Tech Tips

    Use the same procedure for the other tonneau cover holder cap.


    1. Using a screwdriver, detach the 2 claws and remove the tonneau cover holder cap.

      Tech Tips

      Tape the screwdriver tip before use.

  10. REMOVE FRONT DECK SIDE TRIM COVER (w/ Tonneau Cover)

    A00XI2FE01
    Text in Illustration
    *1 Protective tape

    Tech Tips

    Use the same procedure for the other front deck side trim cover.


    1. Using a screwdriver, detach the 2 claws and remove the front deck side trim cover.

      Tech Tips

      Tape the screwdriver tip before use.

  11. REMOVE QUARTER TRIM POCKET TRAY

    A00XHFHE01
    Text in Illustration
    *1 Protective tape

    1. Put protective tape around the quarter trim pocket tray.

    2. Using a screwdriver, detach the 6 claws and 2 guides, and remove the quarter trim pocket tray.

      Tech Tips

      Tape the screwdriver tip before use.

  12. REMOVE OUTER LAP BELT ANCHOR COVER

    A00XDOF

    Tech Tips

    Use the same procedure for the other outer lap belt anchor cover.


    1. Detach the 3 claws and remove the outer lap belt anchor cover.

  13. REMOVE DECK TRIM SIDE PANEL ASSEMBLY LH

    A00XIM7

    1. Remove the bolt and disconnect the front seat outer belt floor anchor.

    2. A00XCXN

      Remove the bolt and disconnect the rear No. 1 seat outer belt floor anchor.

    3. Remove the 3 bolts and 2 screws.

    4. Detach the 9 claws and 12 clips and remove the deck trim side panel.

      A00XKDA

  14. REMOVE REAR QUARTER TRIM PANEL ASSEMBLY LH

    A00XFV7

    1. Move the front shoulder belt anchor adjuster to the lowest position.

    2. Remove the bolt.

    3. Detach the 2 clips and 2 guides.

    4. Pass the front seat outer belt floor anchor through the front quarter trim panel and remove the front quarter trim panel.

  15. REMOVE DOOR CONTROL RECEIVER


    1. A00JWG0E01
      Text in Illustration
      *A w/o Entry and Start System
      *B w/ Entry and Start System

      Disconnect the connector.

    2. Remove the bolt and receiver.