FRONT DOOR LOCK REMOVAL

Tech Tips


  • Use the same procedure for the RH and LH sides.

  • The procedure listed below is for the LH side.


  1. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

    CAUTION:

    Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

    Note


    • After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work Click here.

    • When disconnecting the cable, some systems need to be initialized after the cable is reconnected Click here.

  2. REMOVE FRONT DOOR LOWER FRAME BRACKET GARNISH LH


    1. A00K0GV

      Detach the 2 clips and remove the front door lower frame bracket garnish LH.

  3. REMOVE NO. 2 DOOR INSIDE HANDLE BEZEL LH


    1. A00JYBN

      Using a moulding remover, detach the 3 claws and remove the inside handle bezel as shown in the illustration.

  4. REMOVE ASSIST GRIP COVER LH


    1. A00JY4L

      Using moulding remover A, detach the 8 claws and remove the assist grip cover.

  5. REMOVE FRONT DOOR TRIM BOARD SUB-ASSEMBLY LH


    1. A00JZZF

      Remove the 3 screws.

    2. Remove the 12 clips.

    3. A00K22RE01
      Text in Illustration
      *1 Reference Boss

      Pull out the front door trim board sub-assembly in the direction indicated by the arrow in the illustration.

    4. Raise the front door trim board sub-assembly to detach the 4 claws and remove the front door trim board sub-assembly together with the front door inner glass weatherstrip LH.

    5. A00JZ5R

      Disconnect the 2 connectors.

    6. w/ Seat Position Memory System:


      1. A00JUOF

        Disconnect the connectors.

    7. A00JXET

      Disconnect the front door lock remote control cable assembly and front door inside locking cable assembly.

  6. REMOVE FRONT DOOR INNER GLASS WEATHERSTRIP LH


    1. A00JWX7

      Using a screwdriver, detach the 4 claws and remove the front door inner glass weatherstrip from the front door trim board sub-assembly as shown in the illustration.

  7. REMOVE FRONT DOOR SERVICE HOLE COVER LH


    1. A00K1TG

      Remove the bolt.

    2. Detach the 2 clamps, move the wire harness out of the way and remove the service hole cover.

      Tech Tips

      Remove any remaining butyl tape from the door.

  8. REMOVE FRONT DOOR GLASS SUB-ASSEMBLY LH


    1. Connect the cable to the negative (-) battery terminal.

    2. Connect the power window regulator master switch assembly and move the front door glass sub-assembly so that the door glass bolts can be seen.

    3. Disconnect the cable from the negative (-) battery terminal and power window regulator master switch assembly.

      Note


      • After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work Click here.

      • When disconnecting the cable, some systems need to be initialized after the cable is reconnected Click here.

    4. A00K14P

      Remove the 2 bolts.

      Note

      After the bolts are removed, do not allow the door glass to fall.

    5. A00K1P3E01

      Remove the front door glass sub-assembly as indicated by the arrows in the order shown in the illustration.

      Note

      Do not damage the door glass.

  9. REMOVE FRONT DOOR GLASS RUN LH


    1. A00K0L3

      Remove the front door glass run.

  10. REMOVE FRONT DOOR REAR LOWER FRAME SUB-ASSEMBLY LH


    1. A00JWEK

      Remove the bolt and front door rear lower frame sub-assembly as shown in the illustration.

  11. REMOVE FRONT DOOR OUTSIDE HANDLE COVER WITH LOCK CYLINDER ASSEMBLY


    1. A00JUEH

      Remove the hole plug.

    2. A00JVKU

      Using a T30 "TORX" socket wrench, loosen the screw and remove the front door outside handle cover with lock cylinder assembly.

      Tech Tips

      The screw cannot be removed because it is integrated into the front door outside handle frame sub-assembly.

  12. REMOVE FRONT DOOR LOCK ASSEMBLY LH


    1. Disconnect the connector.

    2. A00JVWRE01
      Text in Illustration
      *A w/o Double Locking System
      *B w/ Double Locking System
      A00JWY4 Slide

      Using a T30 "TORX" wrench, remove the 3 screws.

    3. Slide the front door lock assembly downward, pull out the front door lock open rod from the outside handle frame, and remove the front door lock assembly and cables as a unit.

    4. Remove the front door lock open rod from the front door lock assembly.

    5. Remove the door lock wiring harness seal from the front door lock assembly.

  13. REMOVE FRONT DOOR LOCK REMOTE CONTROL CABLE ASSEMBLY LH


    1. A00K1JD

      Remove the front door lock remote control cable assembly.

  14. REMOVE FRONT DOOR INSIDE LOCKING CABLE ASSEMBLY LH


    1. A00JYRR

      Using a screwdriver, detach the 3 claws.

      Tech Tips

      Tape the screwdriver tip before use.

    2. A00JVN0

      Remove the front door inside locking cable assembly.