LIN COMMUNICATION SYSTEM, Diagnostic DTC:B2322

DTC Code DTC Name
B2322 Front Passenger Side Door ECU Communication Stop

DESCRIPTION

This DTC is stored when LIN communication between the front power window regulator motor assembly RH*1 or LH*2 and main body ECU (multiplex network body ECU) stops for 10 seconds or more.


DTC Code DTC Detection Condition Trouble Area
B2322 No communication between the front power window regulator motor assembly RH*1 or LH*2 and main body ECU (multiplex network body ECU) for 10 seconds or more.

  • Front power window regulator motor assembly RH*1

  • Front power window regulator motor assembly LH*2

  • Main body ECU (multiplex network body ECU)

  • Harness or connector

WIRING DIAGRAM

A009AD1E05

INSPECTION PROCEDURE

Note


  • When using the intelligent tester with the ignition switch off to troubleshoot:

    Connect the intelligent tester to the vehicle and turn a courtesy light switch on and off at 1.5 second intervals until communication between the intelligent tester and vehicle begins.

  • Inspect the fuses and bulbs for circuits related to this system before performing the following inspection procedure.

Tech Tips

When communication between the front power window regulator motor assembly RH*1 or LH*2 and main body ECU (multiplex network body ECU) stops, DTC B2325 is also stored.


  • *1: for LHD

  • *2: for RHD

PROCEDURE


  1. CLEAR DTC


    1. Clear the DTCs Click here.


    NEXT

  2. CHECK FOR DTC


    1. Check for DTCs Click here.

      OK
      DTC B2322 is not output.

    NG

    CHECK HARNESS AND CONNECTOR (MAIN BODY ECU - FRONT POWER WINDOW REGULATOR MOTOR) Click here

    OK

    USE SIMULATION METHOD TO CHECK Click here

  3. CHECK HARNESS AND CONNECTOR (MAIN BODY ECU - FRONT POWER WINDOW REGULATOR MOTOR)


    1. Remove the main body ECU (multiplex network body ECU) from the driver side junction block assembly Click here.

    2. Disconnect the J7*1 or K7*2 front power window regulator motor assembly connector.


      • *1: for LHD

      • *2: for RHD

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      for LHD
      Tester Connection Condition Specified Condition
      A-16 (LIN2) - J7-9 (LIN) Always Below 1 Ω
      A-16 (LIN2) or J7-9 (LIN) - Body ground Always 10 kΩ or higher
      for RHD
      Tester Connection Condition Specified Condition
      A-16 (LIN2) - K7-9 (LIN) Always Below 1 Ω
      A-16 (LIN2) or K7-9 (LIN) - Body ground Always 10 kΩ or higher

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

    OK

  4. CHECK HARNESS AND CONNECTOR (FRONT POWER WINDOW REGULATOR MOTOR - BATTERY AND BODY GROUND)


    1. A0097N2E07
      Text in Illustration
      *A for LHD
      *B for RHD
      *a

      Front view of wire harness connector

      (to Front Power Window Regulator Motor Assembly)

      Disconnect the J7*1 or K7*2 front power window regulator motor assembly connector.


      • *1: for LHD

      • *2: for RHD

    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      for LHD
      Tester Connection Condition Specified Condition
      J7-1 (GND) - Body ground Always Below 1 Ω
      for RHD
      Tester Connection Condition Specified Condition
      K7-1 (GND) - Body ground Always Below 1 Ω

    3. Measure the voltage according to the value(s) in the table below.

      Standard Voltage
      for LHD
      Tester Connection Condition Specified Condition
      J7-2 (B) - Body ground Always 11 to 14 V
      for RHD
      Tester Connection Condition Specified Condition
      K7-2 (B) - Body ground Always 11 to 14 V

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

    OK

  5. REPLACE FRONT POWER WINDOW REGULATOR MOTOR ASSEMBLY


    1. Temporarily replace the front power window regulator motor assembly RH*1 or LH*2 with a new or normally functioning one Click here.


      • *1: for LHD

      • *2: for RHD


    NEXT

  6. CLEAR DTC


    1. Clear the DTCs Click here.


    NEXT

  7. CHECK FOR DTC


    1. Check for DTCs Click here.

      OK
      DTC B2322 is not output.

    NG

    REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU) Click here

    OK

    END (FRONT POWER WINDOW REGULATOR MOTOR IS DEFECTIVE)