CLEARANCE WARNING BUZZER REMOVAL


  1. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

    CAUTION:

    Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

    Note


    • After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work Click here.

    • When disconnecting the cable, some systems need to be initialized after the cable is reconnected Click here.

  2. REMOVE DOOR SCUFF PLATE ASSEMBLY LH (for LHD)

    A00JY1DE01
    Text in Illustration
    *1 Protective Tape

    1. Put protective tape around the door scuff plate.

    2. Using a screwdriver, detach the 4 clips, 10 claws and 2 guides and remove the door scuff plate.

      Tech Tips

      Tape the screwdriver tip before use.

  3. REMOVE COWL SIDE TRIM BOARD LH (for LHD)

    A00JYZF

    1. Remove the clip.

    2. Detach the clip and claw and remove the cowl side trim board.

  4. REMOVE INSTRUMENT SIDE PANEL LH (for LHD)

    A00OAWBE01
    Text in Illustration
    *1 Protective Tape

    1. Put protective tape around the instrument side panel.

    2. Using a moulding remover, detach the 5 clips, claw and 3 guides and remove the instrument side panel.

  5. REMOVE INSTRUMENT CLUSTER FINISH PANEL ORNAMENT (for LHD)

    A00O9INE01
    Text in Illustration
    *1 Protective Tape

    1. Put protective tape around the instrument cluster finish panel ornament.

    2. Using a moulding remover, detach the 3 clips and remove the instrument cluster finish panel ornament.

  6. REMOVE NO. 1 INSTRUMENT PANEL UNDER COVER SUB-ASSEMBLY (for LHD)

    Tech Tips

    Use the same procedure described for the No. 2 instrument panel finish panel cushion.

  7. REMOVE INSTRUMENT PANEL FINISH PLATE GARNISH (for RHD)

    A00O5V3

    1. Detach the 4 clips.

    2. Disconnect each connector and remove the instrument panel finish plate garnish.

  8. REMOVE DOOR SCUFF PLATE ASSEMBLY RH (for RHD)

    A00JUJTE01
    Text in Illustration
    *1 Protective Tape

    1. Put protective tape around the door scuff plate.

    2. Using a screwdriver, detach the 4 clips, 10 claws and 2 guides and remove the door scuff plate.

      Tech Tips

      Tape the screwdriver tip before use.

  9. REMOVE COWL SIDE TRIM BOARD RH (for RHD)

    A00JXPU

    1. Remove the clip.

    2. Detach the clip and claw and remove the cowl side trim board.

  10. REMOVE INSTRUMENT SIDE PANEL RH (for RHD)

    A00JXB3E01
    Text in Illustration
    *1 Protective Tape

    1. Put protective tape around the instrument side panel.

    2. Using a moulding remover, detach the 5 clips, claw and 3 guides and remove the instrument side panel.

  11. REMOVE NO. 2 INSTRUMENT PANEL UNDER COVER SUB-ASSEMBLY (for RHD)


    1. Attach the 3 clips and 2 guides to install the No. 2 instrument panel under cover.

    2. Install the screw.

      A00OAYQE01
      Text in Illustration
      *A for LHD *B for RHD

  12. REMOVE LOWER INSTRUMENT PANEL FINISH PANEL ASSEMBLY

    A00K0ZA

    1. Detach the 4 clips.

    2. Disconnect each connector and remove the instrument panel finish panel.

  13. REMOVE LOWER INSTRUMENT PANEL FINISH PANEL SUB-ASSEMBLY

    A00OAR3E01

    1. Using a screwdriver, detach the 2 claws and open the cover.

      Tech Tips

      Tape the screwdriver tip before use.

      Text in Illustration
      *1 Protective Tape
    2. A00O48R

      w/o Knee Airbag:


      1. Remove the 2 bolts <C>.

      2. Detach the 7 clips.

      3. Disconnect each connector and each cable and remove the lower instrument panel finish panel.

    3. A00OATW

      w/ Knee Airbag:


      1. Remove the 2 bolts <C>.

      2. Detach the 14 clips.

      3. Disconnect each connector and each cable and remove the lower instrument panel finish panel.

  14. REMOVE LOWER NO. 1 INSTRUMENT PANEL AIRBAG ASSEMBLY


    1. A00JYPE

      Remove the 4 bolts and airbag assembly.

    2. Disconnect the connector.

      Note

      When handling the airbag connector, take care not to damage the airbag wire harness.

  15. REMOVE INTEGRATION CONTROL AND PANEL ASSEMBLY

    A00940P

    1. Detach the 4 clips.

    2. Disconnect the connector and remove the integration control and panel assembly.

  16. REMOVE CENTER INSTRUMENT CLUSTER FINISH PANEL ASSEMBLY (w/o Display)

    A00O8AW

    1. Detach the 10 clips.

    2. Disconnect the connector and remove the center instrument cluster finish panel.

  17. REMOVE RADIO TUNER OPENING COVER (w/o Audio)

    A00O9O4

    1. Remove the 4 bolts and radio tuner opening cover.

  18. REMOVE DISPLAY AND NAVIGATION MODULE DISPLAY (w/ Display, w/ Navigation System)


    1. A00K1K3

      Remove the 4 bolts.

    2. A00JZ84

      Pull the display and navigation module display to detach the 8 clips on the backside of the display and navigation module display.

    3. Disconnect the connectors and remove the display and navigation module display.

  19. REMOVE ACCESSORY METER ASSEMBLY (w/ Display, w/o Navigation System)


    1. A0098ZA

      Remove the 2 bolts.

    2. A0095ME

      Pull the accessory meter to detach the 10 clips on the backside of the accessory meter.

    3. Disconnect the connectors and remove the accessory meter.

  20. REMOVE RADIO RECEIVER ASSEMBLY (w/ Audio)


    1. for Upper Side:

      Remove the radio receiver assembly Click here.

    2. for Lower Side:

      Remove the radio receiver assembly Click here.

  21. REMOVE NO. 1 CLEARANCE WARNING BUZZER

    A00OAJC

    1. Disconnect the connector.

    2. Detach the clamp and remove the No. 1 clearance warning buzzer.