CLEARANCE WARNING ECU (for RHD) REMOVAL


  1. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

    CAUTION:

    Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

    Note


    • After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work Click here.

    • When disconnecting the cable, some systems need to be initialized after the cable is reconnected Click here.

  2. REMOVE DOOR SCUFF PLATE ASSEMBLY RH

    A00JUJTE01
    Text in Illustration
    *1 Protective Tape

    1. Put protective tape around the door scuff plate.

    2. Using a screwdriver, detach the 4 clips, 10 claws and 2 guides and remove the door scuff plate.

      Tech Tips

      Tape the screwdriver tip before use.

  3. REMOVE COWL SIDE TRIM BOARD RH

    A00JXPU

    1. Remove the clip.

    2. Detach the clip and claw and remove the cowl side trim board.

  4. REMOVE INSTRUMENT SIDE PANEL RH

    A00JXB3E01
    Text in Illustration
    *1 Protective Tape

    1. Put protective tape around the instrument side panel.

    2. Using a moulding remover, detach the 5 clips, claw and 3 guides and remove the instrument side panel.

  5. REMOVE LOWER INSTRUMENT PANEL FINISH PANEL ASSEMBLY

    A00K0ZA

    1. Detach the 4 clips.

    2. Disconnect each connector and remove the instrument panel finish panel.

  6. REMOVE INSTRUMENT PANEL FINISH PLATE GARNISH

    A00O5V3

    1. Detach the 4 clips.

    2. Disconnect each connector and remove the instrument panel finish plate garnish.

  7. REMOVE NO. 2 INSTRUMENT PANEL UNDER COVER SUB-ASSEMBLY


    1. Attach the 3 clips and 2 guides to install the No. 2 instrument panel under cover.

    2. Install the screw.

      A00OAYQE01
      Text in Illustration
      *A for LHD *B for RHD

  8. REMOVE LOWER INSTRUMENT PANEL FINISH PANEL SUB-ASSEMBLY


    1. A00JYZCE01
      Text in Illustration
      *1 Protective Tape

      Using a screwdriver, detach the 2 claws and open the cover.

    2. A00JWIQ

      Remove the 2 bolts.

    3. Detach the 14 clips.

    4. Disconnect each connector and each cable and remove the lower instrument panel finish panel.

  9. REMOVE LOWER NO. 1 INSTRUMENT PANEL AIRBAG ASSEMBLY

    A00JYLP

    1. Disconnect the connector.

    2. Remove the 4 bolts and Lower No. 1 instrument panel airbag.

      Note

      When handling the airbag connector, take care not to damage the airbag wire harness.

  10. REMOVE DRIVER SIDE JUNCTION BLOCK ASSEMBLY


    1. A00JZKU

      Disconnect the 3 connectors.

    2. A00JW43E06

      Detach the 2 claws and disconnect the 2 connectors labeled (1) as shown in the illustration.

    3. Disconnect the connector labeled (2).

    4. A00JWCE

      Remove the bolt and 2 nuts and disconnect the driver side junction block assembly.

    5. A00JWVI

      Detach the claw and disconnect the connector as shown in the illustration.

    6. A00JXHK

      Detach the 2 claws and release the connector's lock as shown in the illustration.

    7. A00K0WG

      Detach the claw and disconnect the connector as shown in the illustration.

    8. Remove the driver side junction block assembly.

  11. REMOVE CLEARANCE WARNING ECU ASSEMBLY

    A00JXL9

    1. Disconnect the connector.

    2. Remove the bolt and clearance warning ECU.