TELEVISION CAMERA (for Side) REMOVAL


  1. REMOVE OUTER REAR VIEW MIRROR ASSEMBLY LH


    1. Remove the outer rear view mirror Click here.

  2. REMOVE OUTER REAR VIEW MIRROR GLASS

    A009B7UE01

    1. Push the upper part of the mirror surface and tilt it.

    2. Using a moulding remover, detach the 4 claws and separate the outer rear view mirror glass from the mirror body.

      Tech Tips

      Apply protective tape to the outer rear view mirror to prevent it from being damaged.

      Text in Illustration
      *1 Protective Tape
    3. A0099N1

      w/ Mirror Heater:

      Disconnect the 2 connectors and remove the mirror glass.

  3. REMOVE OUTER MIRROR COVER

    A00KX2CE02

    Tech Tips

    Be sure to detach the claws of the outer mirror cover in the order shown in the illustration.


    1. A00KY99E01
      Text in Illustration
      *1 Protective Tape

      Using 2 screwdrivers, detach the 2 claws.

      Tech Tips

      Tape the screwdriver tip before use.

    2. Insert a screwdriver into the slot as shown in the illustration and push on the outer mirror body to create a space between the outer mirror body and outer mirror cover.

      Note

      Be careful not to break the ribs.

      Tech Tips

      Tape the screwdriver tip before use.

      A00KX1YE01
      Text in Illustration
      *1 Protective Tape *2 Rib
      *a Inner Side of Outer Mirror Cover - -
    3. A00KXDTE01
      Text in Illustration
      *1 Protective Tape

      Insert a moulding remover into the space made between the outer mirror body and outer mirror cover.

      Note

      Do not insert the moulding remover more than 4 mm (0.157 in.).

      Tech Tips

      Tape the moulding remover before use.

    4. A00KY7ME01

      Slide the moulding remover downwards as shown in the illustration to detach the 2 claws.

      Note


      • Do not insert the moulding remover more than 4 mm (0.157 in.).

      • Do not slide the moulding remover past the point approximately 40 mm (1.57 in.) from the bottom edge of the outer mirror cover as the outer mirror body will become damaged.

      Standard
      Area Specified Condition
      a 40.0 mm (1.57 in.)

    5. Remove the moulding remover.

    6. A00KSSYE01
      Text in Illustration
      *1 Protective Tape

      Insert a moulding remover between the outer mirror cover and outer mirror body as shown in the illustration and detach the claw.

    7. A00L0ECE01
      Text in Illustration
      *1 Protective Tape

      Using a screwdriver, detach the claw.

    8. A00KSPX

      Detach the 2 claws and remove the outer mirror cover.

      Note

      When removing the cover, be careful not to damage the side turn signal light assembly or cover.

  4. REMOVE SIDE TURN SIGNAL LIGHT ASSEMBLY LH


    1. A0099T6

      Remove the 3 screws and light.

    2. Disconnect the connector.

  5. REMOVE SIDE TELEVISION CAMERA ASSEMBLY


    1. A009AAPE01
      Text in Illustration
      *1 Tape

      Remove the tape.

    2. A009C4G

      Remove the screw, detach the 4 claws and remove the rubber base.

      Tech Tips

      It is not necessary to completely remove the rubber base. Slightly move the rubber base so that the lower mirror cover can be removed in a later step.

    3. Remove the lower mirror cover.


      1. A0098B8E01
        Text in Illustration
        *1 Protective Tape

        Put protective tape around the lower mirror cover.

      2. A0098NBE02
        Text in Illustration
        *1 Protective Tape

        Using a screwdriver, detach the claw.

      3. A0094OIE01
        Text in Illustration
        *1 Protective Tape

        Using a screwdriver, detach the claw.

      4. A0097IVE01
        Text in Illustration
        *1 Protective Tape

        Using a screwdriver, detach the claw to create a space between the lower mirror cover and mirror body as shown in the illustration.

      5. A0097P6E01
        Text in Illustration
        *1 Protective Tape

        Insert a screwdriver as shown in the illustration.

      6. A00957XE01
        Text in Illustration
        *1 Protective Tape

        Detach the claw to create a space between the lower mirror cover and mirror body as shown in the illustration.

      7. A0099TY

        While moving the lower mirror cover back and forth in the directions of the arrows in the illustration, detach the 3 claws and remove the lower mirror cover.

    4. A009BJ4

      Using a T25 "TORX" socket wrench, remove the 3 screws.

    5. A00944H

      Remove the 5 screws.

    6. A009AGSE01

      Using a moulding remover, open the mirror body as shown in the illustration.

    7. Using a moulding remover, detach the 2 claws.

      Note

      Be careful not to break the claw shown in the part of the illustration labeled A.

    8. A0097O7E01

      Using a screwdriver, disconnect the connector.

      Note

      When disconnecting the connector, be careful not to damage it.

      Tech Tips

      Tape the screwdriver tip before use.

      Text in Illustration
      *1 Protective Tape
    9. A009B0O

      Remove the 3 screws and side television camera.