NAVIGATION SYSTEM (for HDD) Steering Pad Switch Circuit

DESCRIPTION

This circuit sends an operation signal from the steering pad switch to the display and navigation module display.

If there is an open in the circuit, the audio system cannot be operated using the steering pad switch.

If there is a short in the circuit, the same condition as when a switch is continuously depressed occurs.

Therefore, the display and navigation module display cannot be operated using the steering pad switch and the display and navigation module display itself cannot function.

WIRING DIAGRAM

A0097L3E04

INSPECTION PROCEDURE

CAUTION:

The vehicle is equipped with an SRS (Supplemental Restraint System) which includes components such as airbags. Before servicing (including removal or installation of parts), be sure to read the Precaution in the SRS section Click here.

PROCEDURE


  1. INSPECT STEERING PAD SWITCH ASSEMBLY


    1. Remove the steering pad switch assembly Click here.

      A0097CDE14

    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Switch Condition Specified Condition
      10 (AU1) - 8 (EAU) No switch is pushed 95 to 105 kΩ
      Seek+ switch is pushed Below 2.5 Ω
      Seek- switch is pushed 313 to 345 Ω
      Volume+ switch is pushed 950 to 1050 Ω
      Volume- switch is pushed 2955 to 3265 Ω
      9 (AU2) - 8 (EAU) No switch is pushed 95 to 105 kΩ
      MODE switch is pushed Below 2.5 Ω
      On hook switch is pushed 313 to 345 Ω
      Off hook switch is pushed 950 to 1050 Ω
      Voice switch is pushed 2955 to 3265 Ω

    NG

    REPLACE STEERING PAD SWITCH ASSEMBLY Click here

    OK

  2. INSPECT SPIRAL CABLE SUB-ASSEMBLY


    1. A0094SWE19
      Text in Illustration
      *a Steering Pad Switch Assembly Side
      *b Vehicle Side

      Remove the spiral cable sub-assembly Click here.

    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      8 (EAU) - 4 (EAU) Spiral cable is turned 2.5 rotations counterclockwise Below 1 Ω
      Spiral cable is centered
      Spiral cable is turned 2.5 rotations clockwise
      10 (AU1) - 6 (AU1) Spiral cable is turned 2.5 rotations counterclockwise
      Spiral cable is centered
      Spiral cable is turned 2.5 rotations clockwise
      9 (AU2) - 5 (AU2) Spiral cable is turned 2.5 rotations counterclockwise
      Spiral cable is centered
      Spiral cable is turned 2.5 rotations clockwise

      CAUTION:

      The spiral cable is an important part of the SRS airbag system. Incorrect removal or installation of the spiral cable may prevent the airbag from deploying. Be sure to read the Precaution in the SRS section Click here.


    NG

    REPLACE SPIRAL CABLE SUB-ASSEMBLY Click here

    OK

  3. CHECK HARNESS AND CONNECTOR (DISPLAY AND NAVIGATION MODULE DISPLAY - SPIRAL CABLE)


    1. Disconnect the H4 display and navigation module display connector.

    2. Disconnect the G40 spiral cable connector.

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      H4-25 (SW1) - G40-6 (AU1) Always Below 1 Ω
      H4-24 (SW2) - G40-5 (AU2) Always Below 1 Ω
      H4-23 (SWG) - G40-4 (EAU) Always Below 1 Ω
      H4-25 (SW1) - Body ground Always 10 kΩ or higher
      H4-24 (SW2) - Body ground Always 10 kΩ or higher
      H4-23 (SWG) - Body ground Always 10 kΩ or higher

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

    OK

    PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE Click here