NAVIGATION SYSTEM (for HDD) PRECAUTION


  1. PRECAUTION FOR DISCONNECTING CABLE FROM NEGATIVE BATTERY TERMINAL

    Note

    After turning the engine switch off, waiting time may be required before disconnecting the cable from the battery terminal. make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work Click here.

  2. IGNITION SWITCH EXPRESSION

    Tech Tips

    The type of ignition switch used on this model differs according to the specifications of the vehicle. The expressions listed in the table below are used in this section.

    Expression Ignition Switch (position) Engine Switch (condition)
    Ignition Switch off Off Off
    Ignition Switch ON ON On (IG)
    Ignition Switch ACC ACC On (ACC)
    Engine Start START Start

  3. PRECAUTIONS FOR DISPLAY AND NAVIGATION MODULE DISPLAY


    1. An HDD is built into the display and navigation module display to store map data, etc, which will be used for the navigation system. Therefore, care must be taken for the following points when handling:

      A00JVT8E01
      Text in Illustration
      *a Example *b Hard Disk Drive
      *c Display and Navigation Module Display - -

      1. Do not subject the display and navigation module display to any vibration or shock.

        Note


        • Do not drop display and navigation module display or subject it to severe impacts.

        • Do not use the display and navigation module display if it has been dropped or subjected to a severe impact.

      2. Do not remove the display and navigation module display if there is a risk that condensation may occur.

        Note

        If the temperature of the display and navigation module display changes rapidly, condensation may occur inside the unit. This may cause a malfunction of the HDD. Therefore, when the display and navigation module display is removed from the instrument panel, it needs to be kept inside the vehicle or in an environment with an equivalent temperature and humidity.

      3. Take measures to prevent static electricity.

        Note

        Touching the terminals of a connector can cause static electricity to be transmitted to the internal circuits. This may cause a malfunction of the HDD.

      4. Keep the display and navigation module display away from magnets or magnetized items.

        Note

        Keep the display and navigation module display away from speakers, motors, magnetized tools and other magnetic items.

  4. PRECAUTIONS FOR HARD DISK DRIVE (HDD)


    1. The map data for the navigation system is stored on the Hard Disk Drive (HDD). Be sure to follow the following instructions when replacing the HDD:

      Note

      Data downloaded by the customer may be stored on the HDD. This data will be lost when the HDD is replaced. Make sure to warn the customer that their data will be lost and obtain their consent prior to replacing the HDD.


      1. The HDD must only be replaced with a new one. Do not attempt to install a used HDD from another vehicle.

        Note

        The display and navigation module display can recognize only a new HDD.

      2. A00JXWQE02
        Text in Illustration
        *a Example
        *b CORRECT
        *c INCORRECT

        Do not touch the HDD cover.

        Note

        When removing or installing the HDD, only hold it by the areas shown in the illustration.

      3. Do not subject the HDD to any vibration or shock .

        Note


        • Do not drop the HDD or allow anything to strike it.

        • Never use an HDD that has been dropped or struck.

      4. Do not remove the HDD if there is a risk that condensation may occur.

        Note

        If the temperature of the HDD changes rapidly, condensation may occur inside the unit. This may cause a malfunction of the HDD. Therefore, when the display and navigation module display is removed from the instrument panel, it needs to be kept inside the vehicle or in an environment with an equivalent temperature and humidity.

      5. Take measures to prevent static electricity.

        Note

        Touching the terminals of a connector can cause static electricity to be transmitted to the internal circuits. This may cause a malfunction of the HDD.

      6. Keep the HDD away from magnets or magnetized items.

        Note

        Keep the HDD away from speakers, motors, magnetized tools and other magnetic items.

      7. Inspect the HDD after replacement.

        Note

        Make sure to perform Check Hard Disk Drive in Operation Check to confirm that there are no HDD abnormalities after removal or installation Click here.