STEERING COLUMN ASSEMBLY (for Power Tilt and Power Telescopic Steering Column) INSTALLATION


  1. CONNECT NO. 2 STEERING INTERMEDIATE SHAFT SUB-ASSEMBLY


    1. Align the matchmarks on the No. 2 steering intermediate shaft and power steering gear.

    2. Install the bolt.

      Torque:
      36 N*m  { 367 kgf*cm, 27 ft.*lbf }

  2. INSTALL NO. 1 STEERING COLUMN HOLE COVER SUB-ASSEMBLY


    1. Install the hole cover with the 4 bolts.

      Torque:
      5.0 N*m  { 51 kgf*cm, 44 in.*lbf }

      Note

      Do not fold back the boot part of the steering hole cover or extend it excessively. If it is extended excessively, return it to its original position.

  3. CONNECT STEERING INTERMEDIATE SHAFT ASSEMBLY


    1. Align the matchmarks on the No. 2 steering intermediate shaft assembly and steering intermediate shaft assembly.

      Tech Tips

      Install the steering intermediate shaft to the inside of the vehicle.

    2. Install the bolt.

      Torque:
      36 N*m  { 367 kgf*cm, 27 ft.*lbf }

  4. INSTALL FRONT NO. 1 FENDER APRON TO FRAME SEAL LH


    1. w/ KDSS:

      Install the apron seal with the 7 clips.

    2. w/o KDSS:

      Install the apron seal with the 4 clips.

  5. INSTALL STEERING COLUMN ASSEMBLY (TILT STEERING GEAR ASSEMBLY WITH MOTOR)


    1. Align the matchmarks on the steering intermediate shaft, steering shaft stopper and steering column.

    2. Install the steering column with the 4 nuts.

      Torque:
      26 N*m  { 265 kgf*cm, 19 ft.*lbf }

    3. Install the bolts.

      Torque:
      36 N*m  { 367 kgf*cm, 27 ft.*lbf }

    4. Attach the claws to install the wire harness protector and wire harness.

  6. INSTALL NO. 1 INSTRUMENT LOWER PANEL AIRBAG ASSEMBLY

    Click here

  7. INSTALL INSTRUMENT LOWER PANEL FINISH PANEL SUB-ASSEMBLY

    Click here

  8. INSTALL COMBINATION SWITCH ASSEMBLY WITH SPIRAL CABLE SUB-ASSEMBLY


    1. Using pliers, grip the claws of the clamp and install the combination switch assembly with spiral cable sub-assembly to the steering column assembly with the clamp.

    2. Connect the connectors to the combination switch with spiral cable.

  9. INSTALL TILT AND TELESCOPIC SWITCH


    1. Attach the claw to install the switch.

    2. Connect the switch connector.

  10. INSTALL STEERING COLUMN UPPER COVER


    1. Attach the claw to install the steering column upper cover.

    2. Attach the 4 clips to install the steering column upper cover to the instrument cluster finish panel.

  11. INSTALL STEERING COLUMN LOWER COVER


    1. Attach the 2 claws to install the steering column lower cover.

      Note

      Do not damage the tilt and telescopic switch.

    2. Install the 3 screws.

  12. ADJUST SPIRAL CABLE SUB-ASSEMBLY


    1. Turn the ignition switch off.

    2. Disconnect the cable from the negative (-) battery terminal.

      CAUTION:

      Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

    3. A0094CF

      Rotate the spiral cable with steering sensor counterclockwise slowly by hand until it feels firm.

      CAUTION:

      Do not turn the spiral cable with steering sensor by the airbag wire harness.

    4. A0095W3E02
      Text in Illustration
      *a Mark

      Rotate the spiral cable with steering sensor clockwise approximately 2.5 turns to align the marks.

      CAUTION:

      Do not turn the spiral cable with steering sensor by the airbag wire harness.

      Tech Tips

      The spiral cable with steering sensor can be rotated approximately 2.5 turns to both the left and right from the center position.

  13. INSTALL STEERING WHEEL ASSEMBLY

    Click here

  14. INSTALL FRONT WHEEL LH

  15. CHECK FRONT WHEELS FACING STRAIGHT AHEAD

  16. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

    Note


    • Reset the auto tilt away function setting to the previous condition by changing the customize parameter Click here.

    • When disconnecting the cable, some systems need to be initialized after the cable is reconnected Click here.

  17. INSPECT SRS WARNING LIGHT

    Click here