OUTPUT SHAFT DISASSEMBLY


  1. INSPECT 1ST GEAR THRUST CLEARANCE


    1. A00XCQE

      Using a dial indicator, measure the thrust clearance.

      Standard clearance
      0.20 to 0.45 mm (0.00787 to 0.0177 in.)

      • If the clearance is not as specified, replace the No. 1 synchronizer ring set.

  2. INSPECT 2ND GEAR THRUST CLEARANCE


    1. A00XDA7

      Using a dial indicator, measure the thrust clearance.

      Standard clearance
      0.10 to 0.25 mm (0.00394 to 0.00984 in.)

      • If the clearance is not as specified, replace the No. 1 synchronizer ring set.

  3. INSPECT 3RD GEAR THRUST CLEARANCE


    1. A00XD1DE01

      Using a feeler gauge, measure the thrust clearance.

      Standard clearance
      0.10 to 0.25 mm (0.00394 to 0.00984 in.)

      • If the clearance is not as specified, replace the No. 2 synchronizer ring set.

  4. INSPECT 1ST GEAR RADIAL CLEARANCE


    1. A00XE05E01

      Using a dial indicator, measure the radial clearance.

      Standard clearance
      0.020 to 0.073 mm (0.000785 to 0.00287 in.)

      • If the clearance is not as specified, replace the 1st gear needle roller bearing with a new one.

  5. INSPECT 2ND GEAR RADIAL CLEARANCE


    1. A00XHGUE01

      Using a dial indicator, measure the radial clearance.

      Standard clearance
      0.015 to 0.068 mm (0.000591 to 0.00267 in.)

      • If the clearance is not as specified, replace the 2nd gear needle roller bearing with a new one.

  6. INSPECT 3RD GEAR RADIAL CLEARANCE


    1. A00XDQME01

      Using a dial indicator, measure the radial clearance.

      Standard clearance
      0.015 to 0.068 mm (0.000591 to 0.00267 in.)

      • If the clearance is not as specified, replace the 3rd gear needle roller bearing with a new one.

  7. REMOVE 1ST GEAR


    1. A00XJAKE01

      Using SST and a press, remove the 5th gear, output shaft center bearing, 1st gear thrust washer and 1st gear from the output shaft.

      SST
      09950-00020

  8. REMOVE NO. 1 SYNCHRONIZER RING SET (for 1st Gear)


    1. A00XHY1

      Remove the synchronizer rings from the output shaft.

  9. REMOVE 1ST GEAR THRUST WASHER PIN


    1. Remove the thrust washer pin from the output shaft.

  10. REMOVE 1ST GEAR NEEDLE ROLLER BEARING


    1. Remove the needle roller bearing from the output shaft.

  11. REMOVE 1ST GEAR BEARING SPACER


    1. Remove the bearing spacer from the output shaft.

  12. REMOVE BEARING SHAFT SNAP RING


    1. A00XHV0E01

      Using 2 screwdrivers and a hammer, tap off the snap ring from the output shaft.

      Note

      Use a piece of cloth to prevent the snap ring from flying off.

  13. REMOVE 2ND GEAR


    1. A00XC8YE01

      Using SST and a press, remove the No. 1 transmission clutch hub with the reverse gear, the No. 1 synchronizer ring set and the 2nd gear from the output shaft.

      SST
      09950-00020

  14. REMOVE 2ND GEAR NEEDLE ROLLER BEARING


    1. Remove the needle roller bearing from the output shaft.

  15. REMOVE REVERSE GEAR


    1. A00XI9WE01

      Remove the reverse gear, 3 No. 1 synchromesh shifting keys and 3 synchromesh shifting key springs.

      Note

      Use a piece of cloth to prevent the shifting keys and shifting key springs from popping out.

  16. REMOVE CLUTCH HUB SET SHAFT SNAP RING


    1. A00XI2KE01

      Using a snap ring expander, remove the snap ring from the output shaft.

      Note

      Do not damage the sliding surface of the bearing.

  17. REMOVE 3RD GEAR


    1. A00XGALE01

      Using SST and a press, remove the No. 2 transmission clutch hub with the No. 2 transmission hub sleeve, the No. 2 synchronizer ring and the 3rd gear from the output shaft.

      SST
      09950-00020

  18. REMOVE 3RD GEAR NEEDLE ROLLER BEARING


    1. Remove the needle roller bearing from the output shaft.

  19. REMOVE NO. 2 TRANSMISSION HUB SLEEVE


    1. A00XJ5NE01

      Remove the No. 2 hub sleeve, 3 No. 2 synchromesh shifting key springs and 3 No. 2 synchromesh shifting keys from the No. 2 clutch hub.