VALVE BODY ASSEMBLY INSTALLATION


  1. INSTALL TRANSMISSION VALVE BODY ASSEMBLY


    1. Install the spring and check ball body.

    2. A0097UPE02
      Text in Illustration
      *1 Pin

      Insert the pin of the manual valve into the hole of the manual valve lever.

    3. A0094SSE01

      Install the transmission valve body with the 19 bolts.

      Torque:
      11 N*m  { 112 kgf*cm, 8 ft.*lbf }

      Tech Tips

      Each bolt length is indicated below.

      32 mm (1.26 in.) for bolt A

      25 mm (0.984 in.) for bolt B

    4. Install the detent spring and detent spring cover with the bolt.

      Torque:
      10 N*m  { 102 kgf*cm, 7 ft.*lbf }

  2. CONNECT TRANSMISSION WIRE


    1. A009821E03
      Text in Illustration
      *1 Orange
      *2 Blue

      Connect the 7 connectors to the solenoid valves.

    2. Connect the 2 ATF temperature sensors with the 2 clamps and 2 bolts.

      Torque:
      for bolt A
      10 N*m  { 102 kgf*cm, 7 ft.*lbf }
      for bolt B
      11 N*m  { 112 kgf*cm, 8 ft.*lbf }

      Tech Tips

      Each bolt length is indicated below.

      12 mm (0.472 in.) for bolt A

      36 mm (1.42 in.) for bolt B

  3. INSTALL VALVE BODY OIL STRAINER ASSEMBLY


    1. Coat a new O-ring with ATF and install it to the oil strainer.

    2. Install the oil strainer with the 4 bolts.

      Torque:
      10 N*m  { 102 kgf*cm, 7 ft.*lbf }

  4. INSTALL AUTOMATIC TRANSMISSION OIL PAN SUB-ASSEMBLY

    Note

    Remove the gasket and be careful not to spill oil on the contacting surfaces of the transmission case and oil pan.


    1. Install a new gasket and the oil pan with the 20 bolts.

      Torque:
      7.0 N*m  { 71 kgf*cm, 62 in.*lbf }

  5. INSTALL REAR NO. 1 ENGINE MOUNTING INSULATOR (for 1KD-FTV)


    1. Install the rear engine mounting insulator to the transmission with the 4 bolts.

      Torque:
      65 N*m  { 663 kgf*cm, 48 ft.*lbf }

  6. INSTALL NO. 3 FRAME CROSSMEMBER SUB-ASSEMBLY (for 1KD-FTV)


    1. Install the frame crossmember to the rear engine mounting insulator with the 4 bolts.

      Torque:
      30 N*m  { 306 kgf*cm, 22 ft.*lbf }

    2. Install the frame crossmember with the 4 bolts and 4 nuts.

      Torque:
      72 N*m  { 734 kgf*cm, 53 ft.*lbf }

  7. INSTALL FRONT SUSPENSION MEMBER BRACKET LH AND RH (for 1KD-FTV)


    1. Install the front suspension member bracket LH and front suspension member bracket RH with the 8 bolts.

      Torque:
      33 N*m  { 337 kgf*cm, 24 ft.*lbf }

  8. ADD AUTOMATIC TRANSMISSION FLUID


    1. Add automatic transmission fluid Click here.

  9. PERFORM RESET MEMORY

    Perform the RESET MEMORY procedures (A/T initialization) (See page 1GR-FE: Click here 1KD-FTV: Click here).