OUTER REAR VIEW MIRROR DISASSEMBLY

Tech Tips


  • Use the same procedure for the and LH sides.

  • The procedure listed below is for the LH side.

  • w/ Side Monitor System:

    When installing only the side television camera assembly, refer to TELEVISION CAMERA (for Side) Click here.


  1. REMOVE OUTER REAR VIEW MIRROR GLASS

    A009B7UE01

    1. Push the upper part of the mirror surface and tilt it.

    2. Using a moulding remover, detach the 4 claws and separate the outer rear view mirror glass from the mirror body.

      Tech Tips

      Apply protective tape to the outer rear view mirror to prevent it from being damaged.

      Text in Illustration
      *1 Protective Tape
    3. A0099N1

      w/ Mirror Heater:

      Disconnect the 2 connectors and remove the mirror glass.

  2. REMOVE OUTER MIRROR COVER LH

    A00KX2CE02

    Tech Tips

    Be sure to detach the claws of the outer mirror cover in the order shown in the illustration.


    1. A00KY99E01
      Text in Illustration
      *1 Protective Tape

      Using 2 screwdrivers, detach the 2 claws.

      Tech Tips

      Tape the screwdriver tip before use.

    2. Insert a screwdriver into the slot as shown in the illustration and push on the outer mirror body to create a space between the outer mirror body and outer mirror cover.

      Note

      Be careful not to break the ribs.

      Tech Tips

      Tape the screwdriver tip before use.

      A00KX1YE01
      Text in Illustration
      *1 Protective Tape *2 Rib
      *a Inner Side of Outer Mirror Cover - -
    3. A00KXDTE01
      Text in Illustration
      *1 Protective Tape

      Insert a moulding remover into the space made between the outer mirror body and outer mirror cover.

      Note

      Do not insert the moulding remover more than 4 mm (0.157 in.).

      Tech Tips

      Tape the moulding remover before use.

    4. A00KY7ME01

      Slide the moulding remover downwards as shown in the illustration to detach the 2 claws.

      Note


      • Do not insert the moulding remover more than 4 mm (0.157 in.).

      • Do not slide the moulding remover past the point approximately 40 mm (1.57 in.) from the bottom edge of the outer mirror cover as the outer mirror body will become damaged.

      Standard
      Area Specified Condition
      a 40.0 mm (1.57 in.)

    5. Remove the moulding remover.

    6. A00KSSYE01
      Text in Illustration
      *1 Protective Tape

      Insert a moulding remover between the outer mirror cover and outer mirror body as shown in the illustration and detach the claw.

    7. A00L0ECE01
      Text in Illustration
      *1 Protective Tape

      Using a screwdriver, detach the claw.

    8. A00KSPX

      Detach the 2 claws and remove the outer mirror cover.

      Note

      When removing the cover, be careful not to damage the side turn signal light assembly or cover.

  3. REMOVE SIDE TURN SIGNAL LIGHT ASSEMBLY LH


    1. A0099T6

      Remove the 3 screws and light.

    2. Disconnect the connector.

  4. REMOVE OUTER MIRROR RETRACTOR LH


    1. Remove the outer rear view mirror gasket LH.


      1. A00KV0EE01
        Text in Illustration
        *a Cut here

        Cut the wire harness sub-assembly at the location shown in the illustration.

        Tech Tips

        A new wire harness sub-assembly is used for reassembly.

      2. A00L0DIE01
        Text in Illustration
        *1 Tape
        *2 Clamp

        Remove the tape and detach the clamp.

    2. A00L0TJE01

      Remove the screw, detach the 5 claws and remove the outer rear view mirror gasket LH.

    3. Remove the lower mirror cover.


      1. A00KX06E01
        A00KZYGE01

        Put protective tape around the lower mirror cover.

        Text in Illustration
        *1 Protective Tape

        Tech Tips

        The claws of the mirror will be detached in the order shown in the illustration in the following steps.

      2. A00KSX1E02
        Text in Illustration
        *1 Protective Tape

        Using a screwdriver, detach the claw.

      3. A00KY05E01
        Text in Illustration
        *1 Protective Tape

        Using a screwdriver, detach the claw.

      4. A00L0KEE01
        Text in Illustration
        *1 Protective Tape

        Using a screwdriver, detach the claw to create a space between the lower mirror cover and mirror body as shown in the illustration.

      5. A00KZ9UE01
        Text in Illustration
        *1 Protective Tape

        Insert a screwdriver as shown in the illustration.

      6. A00KZMUE01
        Text in Illustration
        *1 Protective Tape

        Detach the claw to create a space between the lower mirror cover and cover base as shown in the illustration.

      7. A00KVS9

        While moving the lower mirror cover back and forth in the directions of the arrows in the illustration, detach the 3 claws and remove the lower mirror cover.

    4. A00KZUS

      Using a T25 "TORX" socket wrench, remove the 3 screws.

    5. A00KTQSE01
      Text in Illustration
      *1 Protective Tape

      w/ Side Monitor System:


      1. Remove the connector from the wire clip.

      2. Disconnect the connector.

        Note

        When disconnecting the connector, be careful not to damage it.

    6. A00KSJ0

      Remove the 5 screws and outer mirror body.

    7. A00KYI7E01
      Text in Illustration
      *a A

      Detach the claw and remove the cover body.

      Note

      Be careful as the claw shown in the part of the illustration labeled A is easily damaged.

    8. Remove the actuator sub-assembly.


      1. A00KSXFE01

        Slide the cover as shown in the illustration and disconnect the connector.

      2. A00KSV3E03

        Pull out the wire harness sub-assembly in the direction indicated by the arrow in the illustration.

      3. A00KU3J

        Remove the 3 screws and actuator sub-assembly.

      4. A00KXWC

        Detach the clamp.

      5. Using a thin-bladed screwdriver with its tip wrapped with protective tape, detach the two claws and disconnect the connector.

    9. w/ Side Monitor System:


      1. A00KYQO

        Detach the claw and remove the wire clip.

    10. Remove the support spring.


      1. A00KW71

        Remove the 2 screws, and then detach the 6 claws and remove the 2 support springs.

  5. REMOVE SIDE TELEVISION CAMERA ASSEMBLY (w/ Side Monitor System)


    1. Remove the side television camera assembly Click here.