POWER WINDOW REGULATOR MOTOR (for Front Door) REMOVAL

Tech Tips


  • Use the same procedure for the RH and LH sides.

  • The procedure listed below is for the LH side.


  1. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

    CAUTION:

    Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

    Note


    • After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work Click here.

    • When disconnecting the cable, some systems need to be initialized after the cable is reconnected Click here.

  2. REMOVE FRONT DOOR LOWER FRAME BRACKET GARNISH LH


    1. A00K0GV

      Detach the 2 clips and remove the front door lower frame bracket garnish LH.

  3. REMOVE NO. 2 DOOR INSIDE HANDLE BEZEL LH


    1. A00JYBN

      Using a moulding remover, detach the 3 claws and remove the inside handle bezel as shown in the illustration.

  4. REMOVE ASSIST GRIP COVER LH


    1. A00JY4L

      Using moulding remover A, detach the 8 claws and remove the assist grip cover.

  5. REMOVE FRONT DOOR TRIM BOARD SUB-ASSEMBLY LH


    1. A00JZZF

      Remove the 3 screws.

    2. Remove the 12 clips.

    3. A00K22RE01
      Text in Illustration
      *1 Reference Boss

      Pull out the front door trim board sub-assembly in the direction indicated by the arrow in the illustration.

    4. Raise the front door trim board sub-assembly to detach the 4 claws and remove the front door trim board sub-assembly together with the front door inner glass weatherstrip LH.

    5. A00JZ5R

      Disconnect the 2 connectors.

    6. w/ Seat Position Memory System:


      1. A00JUOF

        Disconnect the connectors.

    7. A00JXET

      Disconnect the front door lock remote control cable assembly and front door inside locking cable assembly.

  6. REMOVE FRONT DOOR INNER GLASS WEATHERSTRIP LH


    1. A00JWX7

      Using a screwdriver, detach the 4 claws and remove the front door inner glass weatherstrip from the front door trim board sub-assembly as shown in the illustration.

  7. REMOVE FRONT NO. 1 SPEAKER ASSEMBLY


    1. A00JY5B

      Disconnect the speaker connector.

    2. Remove the 4 screws.

    3. Detach the 2 claws and remove the speaker.

      Note

      Do not touch the cone of the speaker.

  8. REMOVE FRONT DOOR SERVICE HOLE COVER LH


    1. A00K1TG

      Remove the bolt.

    2. Detach the 2 clamps, move the wire harness out of the way and remove the service hole cover.

      Tech Tips

      Remove any remaining butyl tape from the door.

  9. REMOVE FRONT DOOR GLASS SUB-ASSEMBLY LH


    1. Connect the cable to the negative (-) battery terminal.

    2. Connect the power window regulator master switch assembly and move the front door glass sub-assembly so that the door glass bolts can be seen.

    3. Disconnect the cable from the negative (-) battery terminal and power window regulator master switch assembly.

      Note


      • After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work Click here.

      • When disconnecting the cable, some systems need to be initialized after the cable is reconnected Click here.

    4. A00K14P

      Remove the 2 bolts.

      Note

      After the bolts are removed, do not allow the door glass to fall.

    5. A00K1P3E01

      Remove the front door glass sub-assembly as indicated by the arrows in the order shown in the illustration.

      Note

      Do not damage the door glass.

  10. REMOVE FRONT DOOR WINDOW REGULATOR SUB-ASSEMBLY LH


    1. A00JUFEE01
      Text in Illustration
      *1 Temporary Bolt

      Disconnect the connector.

    2. Loosen the temporary bolt.

      Note

      Do not remove the temporary bolt. If the temporary bolt is removed, the front door window regulator may fall and cause damage.

    3. Remove the 5 bolts.

    4. Remove the front door window regulator sub-assembly.

    5. Remove the temporary bolt from the front door window regulator sub-assembly.

  11. REMOVE FRONT POWER WINDOW REGULATOR MOTOR ASSEMBLY LH


    1. Using a T25 "TORX" socket wrench, remove the 3 screws and the power window regulator motor.

      A00JZEQE03
      Text in Illustration
      *1 Spring - -
      *a Range of Movement - -

      CAUTION:

      Do not place your finger, etc. within the range of movement of the window regulator. When removing the power window regulator motor, the force of the spring causes the window regulator to move in the direction of the arrow shown in the illustration (the direction in which the window rises), which may cause injury. NOTICE: Be careful when removing the screws as the motor may fall and become damaged.