BACK DOOR GLASS (w/ Back Door Tire Carrier) REMOVAL


  1. REMOVE BACK DOOR CENTER GARNISH


    1. A00JXPP

      Detach the 4 clips and remove the back door center garnish.

  2. REMOVE BACK DOOR SIDE GARNISH LH


    1. A00JW8G

      Detach the 2 clips and claw and remove the back door side garnish.

  3. REMOVE BACK DOOR SIDE GARNISH RH


    1. A00JXPA

      Detach the 2 clips and claw and remove the back door side garnish.

  4. REMOVE BACK DOOR TRIM COVER


    1. A00JZC7

      Remove the back door trim cover as shown in the illustration.

  5. REMOVE UPPER TOOL BOX PANEL SUB-ASSEMBLY


    1. A00JV27

      Remove the upper tool box panel sub-assembly as shown in the illustration.

  6. REMOVE TOOL CASE


    1. A00JTVV

      Detach the 2 claws and remove the tool case.

  7. REMOVE BACK DOOR INSIDE HANDLE BEZEL (for Face to Face Seat Type)


    1. A00K0S7

      Remove the screw.

    2. Detach the 5 claws and remove the back door inside handle bezel.

  8. REMOVE BACK DOOR TRIM PANEL ASSEMBLY


    1. A00JWOS

      Detach the claw and remove the cover.

      Tech Tips

      Tape the screwdriver tip before use.

    2. A00JZLH

      Remove the screw.

    3. w/o Back Door Tire Carrier:


      1. A00JX6B

        Remove the bolt.

      2. Detach the 15 clips and remove the back door trim panel assembly.

    4. w/ Back Door Tire Carrier:


      1. A00JZAO

        Remove the bolt.

      2. Detach the 16 clips and remove the back door trim panel assembly.

    5. for Face to Face Seat Type:


      1. A00K0PU

        Remove the screw and bolt.

      2. Detach the 15 clips and remove the back door trim panel assembly.

  9. REMOVE BACK DOOR INSIDE HANDLE SUB-ASSEMBLY (for Face to Face Seat Type)


    1. A00JYJA

      Detach the guide.

    2. Detach the claws and remove the inside handle sub-assembly.

    3. Disconnect the 2 cables from the inside handle sub-assembly.

  10. REMOVE SPARE WHEEL COVER PAD


    1. A00JTU0

      Detach the 7 claws and move the wheel cover pad out of the way.

  11. REMOVE SPARE WHEEL COVER


    1. A00JVLX

      Remove the bolt.

    2. Move the lever.

    3. A00JXSL

      Detach the 8 claws and remove the spare wheel cover.

  12. REMOVE SPARE TIRE

  13. REMOVE NO. 2 SPARE WHEEL COVER


    1. A00JZPU

      Remove the 4 screws and No. 2 spare wheel cover.

  14. REMOVE REAR SPOILER COVER RH

    A0099TWE01
    Text in Illustration
    *1 Fastening Tape

    1. Detach the fastening tape and 5 clips and remove the rear No. 1 spoiler cover.

  15. REMOVE REAR SPOILER SUB-ASSEMBLY


    1. w/o Back Door Tire Carrier:

      Remove the rear spoiler sub-assembly Click here.

    2. w/ Back Door Tire Carrier:

      Remove the rear spoiler sub-assembly Click here.

  16. REMOVE REAR WIPER ARM


    1. A00996T

      Remove the nut and rear wiper arm.

  17. REMOVE REAR WIPER MOTOR ASSEMBLY


    1. A009835E01
      Text in Illustration
      *A w/ Back Door Tire Carrier
      *B w/o Back Door Tire Carrier

      Disconnect the washer hose and wiper motor connector.

    2. A0095XSE01
      Text in Illustration
      *A w/ Back Door Tire Carrier
      *B w/o Back Door Tire Carrier

      Remove the 3 bolts.

    3. Detach the 2 guides and remove the rear wiper motor.

  18. REMOVE NO. 1 BACK WINDOW WIPER MOTOR BRACKET


    1. A00JZH9

      Using a clip remover, detach the clamp.

    2. Remove the 3 bolts.

    3. Using a clip remover, detach the 2 clips and remove the No. 1 back window wiper motor bracket.

  19. REMOVE BACK WINDOW OUTSIDE MOULDING


    1. Using a knife, cut off the 2 outside mouldings as shown in the illustration.

      Note


      • Do not damage the vehicle body with the knife.

      • If the vehicle body is damaged, repair the damaged portion by applying an anti-rust coating after removing the back window glass assembly.

      A00K142E01
      Text in Illustration
      *1 Cut - -

    2. Remove the remaining outside moulding from the back door glass.

  20. REMOVE BACK DOOR GLASS

    A00JZI9E01

    1. Apply protective tape to the outer surface of the vehicle body to prevent scratches.

      Note

      When separating the back window glass from the vehicle, be careful not to damage the vehicle paint or interior/exterior ornaments.

      Text in Illustration
      *1 Protective Tape

    2. Disconnect the connectors.

    3. A00K1RAE01
      Text in Illustration
      *1 Clip
      *2 Adhesive Dam

      From the interior, insert a piano wire between the vehicle body and glass as shown in the illustration.

    4. Tie objects that can serve as handles (for example, wooden blocks) to both wire ends.

    5. Cut off the adhesive by pulling the piano wire around the back window glass.

      Note


      • When separating the glass from the vehicle, be careful not to damage the vehicle paint or interior/exterior ornaments.

      • Leave as much adhesive on the vehicle body as possible when removing the back window glass.

    6. A00K1D6E01
      Text in Illustration
      *a Matchmark

      Place matchmarks over the glass and vehicle body at the locations indicated in the illustration.

      Tech Tips

      Matchmarks do not need to be placed if the glass is not going to be reused.

    7. A00K0XS

      Using suction cups, remove the back door glass.

      Note

      Be careful not to drop the back door glass.

  21. REMOVE BACK WINDOW GLASS CLIP LH


    1. A00JUK5

      Using a scraper, remove the clip.

      Note


      • Be careful not to damage the back door glass.

      • Be sure to replace the clip with new one.

  22. REMOVE BACK WINDOW GLASS CLIP RH


    1. A00JZM1

      Using a scraper, remove the clip.

      Note


      • Be careful not to damage the back door glass.

      • Be sure to replace the clip with new one.

  23. REMOVE BACK DOOR GLASS ADHESIVE DAM


    1. A00JZZI

      Using a scraper, remove the 2 dams.

      Note


      • Be careful not to damage the back door glass.

      • Be sure to replace the 2 dams with new ones.

  24. REMOVE BACK WINDOW UPPER OUTSIDE MOULDING


    1. A00K04ZE01
      Text in Illustration
      *1 Back Window Upper Outside Moulding LH
      *2 Back Window Upper Outside Moulding RH

      Using a scraper, remove the outside moulding LH and RH.

      Note


      • Be careful not to damage the back door glass.

      • Be sure to replace the mouldings with new ones.