ROOF HEADLINING (for 5 Door) REMOVAL

Tech Tips


  • Use the same procedure for RHD and LHD vehicles.

  • The procedure listed below is for LHD vehicles.


  1. PRECAUTION

    Note

    After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work Click here.

  2. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

    Note

    When disconnecting the cable, some systems need to be initialized after the cable is reconnected Click here.

  3. REMOVE REAR NO. 2 SEAT ASSEMBLY (w/ Rear No. 2 Seat)


    1. for Manual Seat Type:

      Remove the rear No. 2 seat assembly Click here.

    2. for Power Seat Type:

      Remove the rear No. 2 seat assembly Click here.

    3. for Face to Face Seat Type:

      Remove the rear No. 2 seat assembly Click here.

  4. REMOVE REAR NO. 1 SEAT ASSEMBLY (w/ Rear No. 1 Seat)


    1. for 60/40 Split Slide Walk-in Seat Type LH Side:

      Remove the rear No. 1 seat assembly Click here.

    2. for 60/40 Split Slide Walk-in Seat Type RH Side:

      Remove the rear No. 1 seat assembly Click here.

  5. REMOVE REAR NO. 1 SEATBACK ASSEMBLY (w/ Rear No. 1 Seat)


    1. for 60/40 Split Double-folding Seat Type LH Side:

      Remove the rear No. 1 seatback assembly Click here.

    2. for 60/40 Split Double-folding Seat Type RH Side:

      Remove the rear No. 1 seatback assembly Click here.

  6. REMOVE DOOR SCUFF PLATE ASSEMBLY LH

    A00XBZRE01
    Text in Illustration
    *1 Protective Tape

    1. Put protective tape around the door scuff plate.

    2. Using a screwdriver, detach the 4 clips, 10 claws and 2 guides and remove the door scuff plate.

      Tech Tips

      Tape the screwdriver tip before use.

  7. REMOVE DOOR SCUFF PLATE ASSEMBLY RH

    Tech Tips

    Use the same procedure described for the LH side.

  8. REMOVE COWL SIDE TRIM BOARD LH

    A00XHBZ

    1. Remove the clip.

    2. Detach the clip and claw and remove the cowl side trim board.

  9. REMOVE COWL SIDE TRIM BOARD RH

    Tech Tips

    Use the same procedure described for the LH side.

  10. REMOVE FRONT DOOR OPENING TRIM WEATHERSTRIP LH

    A00XIF0

    1. Remove the front door opening trim weatherstrip.

  11. REMOVE FRONT DOOR OPENING TRIM WEATHERSTRIP RH

    Tech Tips

    Use the same procedure described for the LH side.

  12. REMOVE FRONT NO. 1 ASSIST GRIP PLUG LH

    A00XKJ0E01
    Text in Illustration
    *1 Protective Tape

    Tech Tips

    Use the same procedure for the other front No. 1 assist grip plug.


    1. Using a screwdriver, detach the 2 claws and remove the front No. 1 assist grip plug.

      Tech Tips

      Tape the screwdriver tip before use.

  13. REMOVE FRONT NO. 1 ASSIST GRIP PLUG RH

    Tech Tips

    Use the same procedure described for the LH side.

  14. REMOVE NO. 1 ASSIST GRIP

    A00XHH5

    Tech Tips

    Use the same procedure for the other No. 1 assist grip.


    1. Remove the 2 bolts.

    2. Detach the 2 claws and remove the No. 1 assist grip.

  15. REMOVE FRONT PILLAR GARNISH LH

    A00XCL0

    1. Detach the 3 guides and remove the front pillar garnish.

    2. A00XF90E01
      Text in Illustration
      *1 Curtain Shield Airbag Assembly
      *2 Adhesive Tape
      *3 Protective Cover

      w/ Curtain Shield Airbag:

      Protect the curtain shield airbag assembly.


      1. Completely cover the airbag with a cloth or nylon sheet and secure the ends of the cover with adhesive tape as shown in the illustration.

        Note

        Cover the curtain shield airbag with a protective cover as soon as the front pillar garnish is removed.

  16. REMOVE FRONT PILLAR GARNISH RH

    Tech Tips

    Use the same procedure described for the LH side.

  17. REMOVE REAR NO. 1 FLOOR STEP COVER (w/ Rear No. 2 Seat)

    A00XJT0E01
    Text in Illustration
    *1 Protective Tape

    Tech Tips

    Use the same procedure for all rear No. 1 floor step covers.


    1. Using a screwdriver, detach the 2 claws and remove the rear No. 1 floor step cover.

      Tech Tips

      Tape the screwdriver tip before use.

  18. REMOVE QUARTER SCUFF PLATE LH (w/ Rear No. 2 Seat)

    A00XFB0

    1. Remove the 2 bolts and quarter scuff plate.

  19. REMOVE QUARTER SCUFF PLATE RH (w/ Rear No. 2 Seat)

    Tech Tips

    Use the same procedure described for the LH side.

  20. REMOVE REAR DOOR SCUFF PLATE LH

    A00XHCZE01
    Text in Illustration
    *1 Protective Tape

    1. Put protective tape around the rear door scuff plate.

    2. Using a screwdriver, detach the 3 clips, 6 claws and 2 guides and remove the rear door scuff plate.

      Tech Tips

      Tape the screwdriver tip before use.

  21. REMOVE REAR DOOR SCUFF PLATE RH

    Tech Tips

    Use the same procedure described for the LH side.

  22. REMOVE REAR DOOR OPENING TRIM WEATHERSTRIP LH

    A00XDLP

    1. Remove the rear door opening trim weatherstrip.

  23. REMOVE REAR DOOR OPENING TRIM WEATHERSTRIP RH

    Tech Tips

    Use the same procedure described for the LH side.

  24. REMOVE OUTER LAP BELT ANCHOR COVER

    A00XGRT

    Tech Tips

    Use the same procedure for the other outer lap belt anchor cover.


    1. Detach the 3 claws and remove the outer lap belt anchor cover.

  25. REMOVE LOWER CENTER PILLAR GARNISH LH

    A00XHF4

    1. Remove the bolt and disconnect the front seat outer belt floor anchor.

    2. A00XGTG

      Detach the 4 claws and 2 clips and remove the lower center pillar garnish.

  26. REMOVE LOWER CENTER PILLAR GARNISH RH

    Tech Tips

    Use the same procedure described for the LH side.

  27. REMOVE NO. 2 ASSIST GRIP PLUG LH

    A00XC86E01
    Text in Illustration
    *1 Protective Tape

    Tech Tips

    Use the same procedure for the other front No. 2 assist grip plug.


    1. Using a screwdriver, detach the 2 claws and remove the front No. 2 assist grip plug.

      Tech Tips

      Tape the screwdriver tip before use.

  28. REMOVE NO. 2 ASSIST GRIP PLUG RH

    Tech Tips

    Use the same procedure described for the LH side.

  29. REMOVE NO. 2 ASSIST GRIP

    A00XC40

    Tech Tips

    Use the same procedure for the other No. 2 assist grip.


    1. Remove the 2 bolts.

    2. Detach the 2 claws and remove the No. 2 assist grip.

  30. REMOVE CENTER PILLAR GARNISH LH

    A00XJYH

    1. Move the front shoulder belt anchor adjuster to the lowest position.

    2. Remove the bolt.

    3. Detach the 2 clips and 2 guides.

    4. Pass the front seat outer belt floor anchor through the center pillar garnish and remove the center pillar garnish.

  31. REMOVE CENTER PILLAR GARNISH RH

    Tech Tips

    Use the same procedure described for the LH side.

  32. REMOVE TONNEAU COVER ASSEMBLY (w/ Tonneau Cover)


    1. Remove the tonneau cover.

  33. REMOVE FRONT LUGGAGE COMPARTMENT TRIM COVER (w/o Rear No. 2 Seat)

    A00XHLO

    Tech Tips

    Use the same procedure for the other front luggage compartment trim cover.


    1. Detach the 4 claws and remove the cap.

    2. A00XKI2E01
      Text in Illustration
      *1 Luggage Hold Belt Striker

      Remove the bolt, luggage hold belt striker and front luggage compartment trim cover.

  34. REMOVE NO. 1 DECK BOARD SUB-ASSEMBLY (w/o Rear No. 2 Seat)

    A00XFDO

    1. Detach the clip and remove the No. 1 deck board.

  35. REMOVE REAR FLOOR MAT REAR SUPPORT PLATE (w/o Rear No. 2 Seat)

    A00XGTD

    1. Detach the 5 clips and 4 claws and remove the rear floor mat rear support plate.

  36. REMOVE FLOOR SIDE RAIL LH (w/ Deck Rail)

    A00XDK3

    1. Remove the 3 bolts and floor side rail.

  37. REMOVE FLOOR SIDE RAIL RH (w/ Deck Rail)

    Tech Tips

    Use the same procedure described for the LH side.

  38. REMOVE REAR FLOOR CARPET ASSEMBLY (w/o Rear No. 2 Seat)


    1. Detach the 4 claws and remove the rear floor carpet.

      A00XJD9E01
      Text in Illustration
      *A w/o Deck Rail *B w/ Deck Rail
      *C for Face to Face Seat Type - -

  39. REMOVE REAR NO. 1 SEAT OUTER LAP BELT ANCHOR COVER

    A00XCE8

    Tech Tips

    Use the same procedure for the other rear No. 1 seat outer lap belt anchor cover.


    1. Detach the 3 claws and remove the rear No. 1 seat outer lap belt anchor cover.

  40. REMOVE NO. 1 LUGGAGE COMPARTMENT TRIM HOOK

    A00XHK8

    Tech Tips

    Use the same procedure for the other No. 1 luggage compartment trim hook.


    1. Remove the luggage compartment trim hook by turning it clockwise.

  41. REMOVE NO. 1 TONNEAU COVER HOLDER CAP (w/o Tonneau Cover)

    A00XHNJE01
    Text in Illustration
    *1 Protective Tape

    Tech Tips

    Use the same procedure for the other No. 1 tonneau cover holder cap.


    1. Using a screwdriver, detach the 2 claws and remove the No. 1 tonneau cover holder cap.

      Tech Tips

      Tape the screwdriver tip before use.

  42. REMOVE FRONT DECK SIDE TRIM COVER (w/ Tonneau Cover)

    A00XI2FE01
    Text in Illustration
    *1 Protective Tape

    Tech Tips

    Use the same procedure for the other front deck side trim cover.


    1. Using a screwdriver, detach the 2 claws and remove the front deck side trim cover.

      Tech Tips

      Tape the screwdriver tip before use.

  43. REMOVE ASSIST GRIP PLUG (w/ Rear No. 2 Seat)

    A00XI26E01
    Text in Illustration
    *1 Protective Tape

    Tech Tips

    Use the same procedure for all assist grip plugs.


    1. Using a screwdriver, detach the 2 claws and remove the assist grip plug.

      Tech Tips

      Tape the screwdriver tip before use.

  44. REMOVE ASSIST GRIP SUB-ASSEMBLY (w/ Rear No. 2 Seat)

    A00XGDT

    Tech Tips

    Use the same procedure for the other assist grip.


    1. Remove the 2 bolts and assist grip.

  45. REMOVE DECK TRIM SIDE PANEL ASSEMBLY LH


    1. w/o Rear No. 2 Seat:


      1. A00XBXK

        Remove the bolt and disconnect the rear No. 1 seat outer belt floor anchor.

      2. A00XER5

        Detach the 6 claws and 2 guides and disconnect the rear seatback lock control lever base.

      3. Remove the 4 bolts and 2 screws.

      4. Detach the 5 clips and 8 claws.

      5. Pass the rear seatback lock control lever base through the deck trim side panel and remove the deck trim side panel.

        A00XDD2

    2. w/ Rear No. 2 Seat:


      1. A00XBXK

        Remove the bolt and disconnect the rear No. 1 seat outer belt floor anchor.

      2. A00XF16

        Remove the bolt and disconnect the rear No. 2 seat outer belt floor anchor.

      3. Remove the 2 bolts and 2 screws.

      4. Detach the 4 clips and 8 claws and remove the deck trim side panel.

        A00XDFD

  46. REMOVE DECK TRIM SIDE PANEL ASSEMBLY RH


    1. w/o Rear No. 2 Seat:


      1. A00XCL5

        Remove the bolt and disconnect the rear No. 1 seat outer belt floor anchor.

      2. A00XCYB

        Detach the 6 claws and 2 guides and disconnect the rear seatback lock control lever base.

      3. Remove the 4 bolts and screws.

      4. Detach the 5 clips and 8 claws.

      5. Disconnect each connector.

      6. Pass the rear seatback lock control lever base through the deck trim side panel and remove the deck trim side panel.

        A00XI9A

    2. w/ Rear No. 2 Seat:


      1. A00XCL5

        Remove the bolt and disconnect the rear No. 1 seat outer belt floor anchor.

      2. A00XI3Y

        Remove the bolt and disconnect the rear No. 2 seat outer belt floor anchor.

      3. Remove the 2 bolts and screw.

      4. Detach the 4 clips and 8 claws.

      5. Disconnect each connector and remove the deck trim side panel.

        A00XDMS

  47. REMOVE FRONT QUARTER TRIM PANEL ASSEMBLY LH

    A00XJ7M

    1. Move the rear shoulder belt anchor adjuster to the lowest position.

    2. Detach the 2 clips and 2 guides.

    3. Pass the rear No. 1 seat outer belt floor anchor through the front quarter trim panel and remove the front quarter trim panel.

  48. REMOVE FRONT QUARTER TRIM PANEL ASSEMBLY RH

    Tech Tips

    Use the same procedure described for the LH side.

  49. REMOVE REAR QUARTER TRIM PANEL ASSEMBLY LH

    A00XJG8

    1. w/o Rear No. 2 Seat:


      1. Detach the 7 clips and 2 guides and remove the rear quarter trim panel.

    2. A00XI6E

      w/ Rear No. 2 Seat:


      1. Detach the 7 clips and 2 guides.

      2. A00XETV

        Detach the 4 clips and 2 guides, pass the rear No. 2 seat outer belt floor anchor through the rear quarter trim panel and remove the rear quarter trim panel.

  50. REMOVE REAR QUARTER TRIM PANEL ASSEMBLY RH

    Tech Tips

    Use the same procedure described for the LH side.

  51. REMOVE ASSIST GRIP SUB-ASSEMBLY

    A00XDMYE03
    Text in Illustration
    *1 Protective Tape

    Tech Tips

    Use the same procedure for the other assist grip.


    1. Using a screwdriver, detach the 4 claws and remove the 2 assist grip covers.

      Tech Tips

      Tape the screwdriver tip before use.

    2. Detach the 2 clips and remove the assist grip.

    3. Remove the 2 clips from the vehicle body.

  52. REMOVE REAR ASSIST GRIP ASSEMBLY LH

    A00XKIGE03
    Text in Illustration
    *1 Protective Tape

    1. Using a screwdriver, detach the 4 claws and remove the 2 assist grip covers.

      Tech Tips

      Tape the screwdriver tip before use.

    2. Detach the 2 clips and remove the assist grip.

    3. Remove the 2 clips from the vehicle body.

  53. REMOVE REAR ASSIST GRIP ASSEMBLY RH

    Tech Tips

    Use the same procedure described for the LH side.

  54. REMOVE ASSIST GRIP (w/ Rear No. 2 Seat)

    A00XHX7E01

    Tech Tips

    Use the same procedure for the other assist grip.


    1. Using a screwdriver, detach the 4 claws and open the 2 covers.

      Tech Tips

      Tape the screwdriver tip before use.

      Text in Illustration
      *1 Protective Tape
    2. A00XFZU

      Remove the 2 bolts and assist grip.

  55. REMOVE VISOR BRACKET COVER LH

    A00XF6M

    Tech Tips

    Use the same procedure for the other visor bracket cover.


    1. Detach the 4 claws and remove the visor bracket cover.

  56. REMOVE VISOR BRACKET COVER RH

    Tech Tips

    Use the same procedure described for the LH side.

  57. REMOVE VISOR ASSEMBLY LH

    A00XDU4

    1. Remove the 2 screws and visor.

  58. REMOVE VISOR ASSEMBLY RH

    Tech Tips

    Use the same procedure described for the LH side.

  59. REMOVE VISOR HOLDER

    A00XKBFE02

    Tech Tips

    Use the same procedure for the other visor holder.


    1. Turn the visor holder approximately 45° and pull it out as shown in the illustration.

    2. Detach the 2 claws and remove the visor holder.

  60. REMOVE MAP LIGHT ASSEMBLY


    1. A0097TU

      Detach the 4 clips.

    2. Disconnect the connector and remove the map light.

  61. REMOVE RAIN SENSOR COVER (w/ Rain Sensor)


    1. A0097L5

      Detach the 2 claws and remove the rain sensor cover.

  62. REMOVE INNER REAR VIEW MIRROR STAY HOLDER COVER (w/ EC Mirror)


    1. A00K06K

      Detach the 2 claws and slide the inner rear view mirror stay holder cover in the direction indicated by the arrow in the illustration.

    2. A00JZU1

      Detach the 2 claws and remove the inner rear view mirror stay holder cover.

  63. REMOVE NO. 1 ROOM LIGHT ASSEMBLY


    1. Remove the No. 1 room light assembly Click here.

  64. REMOVE NO. 2 ROOM LIGHT ASSEMBLY


    1. Remove the No. 2 room light assembly Click here.

  65. REMOVE TELEVISION BASE (w/ Rear Seat Entertainment System)

    A00XDBB

    1. Using a moulding remover, detach the 6 claws and 4 clips and remove the television base.

  66. REMOVE ROOF HEADLINING ASSEMBLY

    A00XFNM

    1. w/ EC Mirror:

      Disconnect the inner mirror connector.

    2. A00XGGX

      w/ Rain Sensor:

      Disconnect the rain sensor connector.

    3. A00XJC8

      w/ Sliding Roof:

      Disconnect the drive gear connector.

    4. A00XHZI

      Disconnect the 2 connectors and detach the 3 clamps from the front pillar LH.

    5. A00XDOI

      Remove the bolt.

    6. Disconnect the 2 connectors and detach the 3 clamps from the front pillar RH.

    7. A00XG9K

      Disconnect the 2 connectors and detach the clamp from the rear pillar LH.

    8. A00XFXN

      Disconnect the connector and detach the 3 clamps from the rear pillar RH.

    9. A00XGGE

      w/ Rear Seat Entertainment System:

      Disconnect the 2 connectors.

    10. A00XHUN

      w/o Sliding Roof:


      1. Detach the 2 clips.

    11. A00XD86E01
      Text in Illustration
      *1 Guide
      *2 Fastener

      w/ Sliding Roof:


      1. Detach the 2 clips, 2 guides and 8 fasteners.

    12. A00XD4GE01
      Text in Illustration
      *1 Guide
      *2 Fastener

      w/ Rear Seat Entertainment System:


      1. Detach the 2 clips, 2 guides and 6 fasteners.

    13. A00XCYH

      Remove the roof headlining from the back door as shown in the illustration.

      Note

      Be careful not to damage the roof headlining when removing it.

  67. REMOVE FRONT SHOULDER BELT ANCHOR PLATE SUB-ASSEMBLY LH

    A00XFY9

    1. Detach the 5 claws of the front shoulder belt anchor plate and slide the front shoulder belt anchor plate in the direction of the arrow to remove it.

  68. REMOVE FRONT SHOULDER BELT ANCHOR PLATE SUB-ASSEMBLY RH

    Tech Tips

    Use the same procedure described for the LH side.

  69. REMOVE REAR SHOULDER BELT ANCHOR PLATE SUB-ASSEMBLY LH

    A00XI18

    1. Detach the 6 claws of the rear shoulder belt anchor plate and slide the rear shoulder belt anchor plate in the direction of the arrow to remove it.

  70. REMOVE REAR SHOULDER BELT ANCHOR PLATE SUB-ASSEMBLY RH

    Tech Tips

    Use the same procedure described for the LH side.

  71. REMOVE NO. 1 ROOF SIDE RAIL GARNISH LH

    A00XCL4E01
    Text in Illustration
    *a Cut Off Position

    1. Detach the 3 clips.

    2. Cut off the 3 clips and remove the roof side rail garnish.

    3. Remove 3 clips from the vehicle body.

  72. REMOVE NO. 1 ROOF SIDE RAIL GARNISH RH

    Tech Tips

    Use the same procedure described for the LH side.

  73. REMOVE ROOF SIDE INNER GARNISH CAP LH (w/o Rear No. 2 Seat)

    A00XCK4

    1. Detach the 4 claws and 2 guides and remove the roof side inner garnish cap.

  74. REMOVE ROOF SIDE INNER GARNISH CAP RH (w/o Rear No. 2 Seat)

    Tech Tips

    Use the same procedure described for the LH side.

  75. REMOVE REAR SEAT SHOULDER BELT HANGER LH

    A00XHJB

    1. Detach the claw and guide and remove the rear seat shoulder belt hanger.

  76. REMOVE REAR SEAT SHOULDER BELT HANGER RH

    Tech Tips

    Use the same procedure described for the LH side.

  77. REMOVE QUARTER TRIM COVER

    A00XHIL

    Tech Tips

    Use the same procedure for the other quarter trim cover.


    1. Detach the 2 claws and remove the quarter trim cover.

  78. REMOVE QUARTER TRIM JACK COVER

    A00XJXD

    1. Detach the 3 claws and 2 guides and remove the quarter trim jack cover.

  79. REMOVE DECK SIDE TRIM COVER LH

    A00XCDU

    1. Detach the 3 claws and 2 guides and remove the deck side trim cover.

  80. REMOVE REAR SIDE RAIL SPACER LH (w/o Curtain Shield Airbag)

    A00XCWJ

    1. Detach the 2 claws and remove the rear side rail spacer.

  81. REMOVE REAR SIDE RAIL SPACER RH (w/o Curtain Shield Airbag)

    Tech Tips

    Use the same procedure described for the LH side.

  82. REMOVE REAR NO. 2 SIDE RAIL SPACER LH (w/o Curtain Shield Airbag)

    A00XI1O

    1. Detach the 2 claws and remove the rear No. 2 side rail spacer.

  83. REMOVE REAR NO. 2 SIDE RAIL SPACER RH (w/o Curtain Shield Airbag)

    Tech Tips

    Use the same procedure described for the LH side.

  84. REMOVE REAR NO. 3 SIDE RAIL SPACER LH

    A00XK9F

    1. Detach the 2 claws and remove the rear No. 3 side rail spacer.

  85. REMOVE REAR NO. 3 SIDE RAIL SPACER RH

    Tech Tips

    Use the same procedure described for the LH side.