HEATER WATER PUMP INSTALLATION

INSTALL NO. 1 VISCOUS HEATER BRACKET SUB-ASSEMBLY

1. Install the No. 1 viscous heater bracket with the 4 bolts.

   Torque:

   45 N*m  { 459 kgf*cm, 33 ft.*lbf }

INSTALL COMPRESSOR OUTLET ELBOW

1. Install the compressor outlet elbow with the 2 bolts and tighten the hose clamp.

   Torque:

   for bolt

   20 N*m  { 204 kgf*cm, 15 ft.*lbf }

   for hose clamp

   6.5 N*m  { 66 kgf*cm, 58 in.*lbf }

2. Install the wire harness bracket with the bolt.

   Torque:

   8.0 N*m  { 82 kgf*cm, 71 in.*lbf }

3. Attach the 3 wire harness clamps.

INSTALL AIR CLEANER CASE SUB-ASSEMBLY

1. Install the air cleaner case with the 3 bolts.

   Torque:

   12 N*m  { 122 kgf*cm, 9 ft.*lbf }

INSTALL AIR CLEANER CAP SUB-ASSEMBLY

1. Attach the 4 clamps to install the air cleaner cap.

2. except Cold Area Specification Vehicles:

   Attach the 2 clamps and connect the mass air flow meter connector.

3. for Cold Area Specification Vehicles:

   Attach the 3 clamps and connect the mass air flow meter connector.

INSTALL NO. 1 AIR CLEANER HOSE

Text in Illustration

*1	No. 1 Air Cleaner Hose	*2	Compressor Inlet Elbow
*3	Air Cleaner Cap	*4	Protrusion
*5	Groove	-	-
*a	Upper Side	*b	Front Side of Vehicle

1. Install the No. 1 air cleaner hose.

   Note

   
   

   • When installing the No. 1 air cleaner hose, align its protrusion with the protrusion of the compressor inlet elbow as shown in the illustration.

   • When installing the No. 1 air cleaner hose, align its groove with the protrusion of the air cleaner cap as shown in the illustration.

2. Tighten the 2 hose clamps.

   Torque:

   5.0 N*m  { 51 kgf*cm, 44 in.*lbf }

   Note

   When tightening the 2 hose clamps, make sure that they are positioned as shown in the illustration.

INSTALL BATTERY HOLD DOWN CLAMP

1. Install the battery hold down clamp with the 2 nuts.

   Torque:

   6.0 N*m  { 61 kgf*cm, 53 in.*lbf }

ADD ENGINE COOLANT

1. Tighten the radiator drain cock plug by hand.

2. Tighten the cylinder block drain cock plug.

   Torque:

   8.0 N*m  { 82 kgf*cm, 71 in.*lbf }

3. Fill the radiator with TOYOTA Super Long Life Coolant (SLLC) to the B line of the reservoir tank.

   Standard Capacity
   Item Specified Condition for Automatic Transmission w/ Rear Heater 14.9 liters (15.7 US qts, 13.1 Imp. qts) w/o Rear Heater 13.1 liters (13.8 US qts, 11.5 Imp. qts) for Manual Transmission w/ Rear Heater 15.0 liters (15.8 US qts, 13.2 Imp. qts) w/o Rear Heater 13.2 liters (13.9 US qts, 11.6 Imp. qts)

   Tech Tips

   
   

   • TOYOTA vehicles are filled with TOYOTA SLLC at the factory. In order to avoid damage to the engine cooling system and other technical problems, only use TOYOTA SLLC or similar high quality ethylene glycol based non-silicate, non-amine, non-nitrite, non-borate coolant with long-life hybrid organic acid technology (coolant with long-life hybrid organic acid technology consists of a combination of low phosphates and organic acids).

   • Please contact your TOYOTA dealer for further details.

   • for Cold Area Specification Vehicles:

     Please contact any authorized TOYOTA dealer or repairer or another duly qualified and equipped professional for further details.

   Note

   Never use water as a substitute for engine coolant.

4. Press the inlet and outlet radiator hoses several times by hand, and then check the level of the coolant.

   If the coolant level drops below the B line, add TOYOTA SLLC to the B line.

5. Install the radiator reservoir cap.

6. Using a wrench, install the vent plug.

   Torque:

   2.0 N*m  { 20 kgf*cm, 18 in.*lbf }

7. Bleed air from the cooling system.

   
   

   1. Warm up the engine until the thermostat opens. While the thermostat is open, circulate the coolant for several minutes.

   2. Maintain the engine speed at 2500 to 3000 rpm.

   3. Press the inlet and outlet radiator hoses several times by hand to bleed air.

      CAUTION:

      When pressing the radiator hoses:

      
      

      • Wear protective gloves.

      • Be careful as the radiator hoses are hot.

      • Keep your hands away from the radiator fan.

   4. Stop the engine and wait until the coolant cools down to ambient temperature.

      CAUTION:

      Do not remove the radiator reservoir cap while the engine and radiator are still hot. Pressurized, hot engine coolant and steam may be released and cause serious burns.

8. After the coolant cools down, check that the coolant level is at the FULL line.

   If the coolant level is below the FULL line, add TOYOTA SLLC to the FULL line.

INSTALL NO. 1 ENGINE UNDER COVER SUB-ASSEMBLY

1. Install the No. 1 engine under cover with the 4 bolts.

   Torque:

   29 N*m  { 296 kgf*cm, 21 ft.*lbf }

INSPECT FOR COOLANT LEAK

1. Fill the radiator with coolant and attach a radiator cap tester.

2. Warm up the engine.

3. Using the radiator cap tester, increase the pressure inside the radiator to 123 kPa (1.3 kgf/cm², 18 psi), and check that the pressure does not drop.

   If the pressure drops, check the hoses, radiator and water pump for leaks. If no external leaks are found, check the heater core, cylinder block and head.

INSTALL UPPER RADIATOR SUPPORT SEAL

1. Install the upper radiator support seal with the 13 clips.