WASHER MOTOR (for Rear Side) INSTALLATION


  1. INSTALL REAR WASHER MOTOR AND PUMP ASSEMBLY


    1. Install the windshield washer motor and pump to the packing of the washer jar.

  2. INSTALL WINDSHIELD WASHER JAR ASSEMBLY


    1. A00XHXUE01

      Attach the guide to install the washer jar, and then install the 3 screws.

      Torque:
      5.5 N*m  { 56 kgf*cm, 49 in.*lbf }

      Note

      Tighten the screws in the order shown in the illustration.

    2. w/o Headlight Cleaner System:

      Connect the connector.

    3. w/ Headlight Cleaner System:

      Connect the 3 connectors.

  3. INSTALL WASHER INLET SUB-ASSEMBLY


    1. Attach the claw to install the washer inlet sub-assembly.

  4. FILL WASHER JAR WITH WASHER FLUID


    1. Connect the washer hose to the hose of the windshield washer motor and pump assembly and fill the washer jar with washer fluid.

  5. INSTALL FRONT FENDER SPLASH SHIELD SUB-ASSEMBLY RH


    1. Attach 13 new grommets to install the front fender splash shield sub-assembly.

    2. Install the 2 screws.

  6. INSTALL FRONT FENDER MUDGUARD RH


    1. Install the front fender mudguard with the 4 screws and 2 clips.

  7. INSTALL FRONT WHEEL

    Torque:
    112 N*m  { 1137 kgf*cm, 82 ft.*lbf }
  8. INSTALL FRONT BUMPER COVER


    1. Install the lower front bumper cover with the 5 bolts and clip.

  9. INSTALL RADIATOR GRILLE


    1. Install the radiator grille Click here.

  10. PREPARATION FOR FOG LIGHT AIMING (w/ Fog Light)


    1. A00XISGE01
      Text in Illustration
      *a 25 or 3 m

      Prepare the vehicle (except China and Taiwan):


      • Place the vehicle in a location that is dark enough to clearly observe the cutoff line. The cutoff line is a distinct line, below which light from the headlights can be observed and above which it cannot.

      • Place the vehicle at a 90° angle to the wall.

      • Create a 25 m (82.0 ft.) distance between the vehicle (headlight bulb center) and wall.

      • Make sure that the vehicle is on a level surface.

      • Bounce the vehicle up and down to settle the suspension.

      Note

      A distance of 25 m (82.0 ft.) between the vehicle (headlight bulb center) and wall is necessary for proper aim adjustment. If unavailable, secure a distance of exactly 3 m (9.84 ft.) for the check and adjustment (the target zone will change with the distance, so follow the instructions in the illustration).

    2. A00XISGE01
      Text in Illustration
      *a 10 or 3 m

      Prepare the vehicle (for China and Taiwan):


      • Place the vehicle in a location that is dark enough to clearly observe the cutoff line. The cutoff line is a distinct line, below which light from the headlights can be observed and above which it cannot.

      • Place the vehicle at a 90° angle to the wall.

      • Create a 10 m (32.8 ft) distance between the vehicle (headlight bulb center) and the wall.

      • Make sure that the vehicle is on a level surface.

      • Bounce the vehicle up and down to settle the suspension.

      Note

      A distance of 10 m (32.8 ft) between the vehicle (headlight bulb center) and the wall is necessary for proper aim adjustment. If unavailable, secure a distance of exactly 3 m (9.84 ft) for check and adjustment. (The target zone will change with the distance so follow the instructions in the illustration.)

    3. Prepare a piece of thick white paper approximately 2 m (6.56 ft.) (height) x 4 m (13.1 ft.) (width) to use as a screen.

    4. Draw a vertical line down the center of the screen (V line).

    5. except China and Taiwan:

      Set the screen as shown in the illustration.

      A00XIMNE01

      Tech Tips


      • Stand the screen perpendicular to the ground.

      • Align the V line on the screen with the center of the vehicle.

    6. for China and Taiwan:

      Set the screen as shown in the illustration.

      A00XIMNE03

      Tech Tips


      • Stand the screen perpendicular to the ground.

      • Align the V line on the screen with the center of the vehicle.

    7. Prepare a piece of thick white paper approximately 2 m (6.56 ft.) (height) x 4 m (13.1 ft.) (width) to use as a screen.

    8. Draw a vertical line down the center of the screen (V line).

    9. A00XGUXE01
      Text in Illustration
      *a V LH Line
      *b V Line
      *c V RH Line
      *d H Line
      *e Ground

      Draw base lines (H, V LH, and V RH Lines) on the screen as shown in the illustration.

      Tech Tips


      • The base lines differ for "low beam inspection" and "high beam inspection".

      • Mark the headlight bulb center marks on the screen. If the center mark cannot be observed on the headlight, use the center of the headlight bulb or the name of the manufacturer marked on the headlight as the center mark.


      1. H Line (Headlight):

        Draw a horizontal line across the screen so that it passes through the center marks. The H line should be at the same height as the headlight bulb center marks of the low beam headlights.

      2. V LH Line, V RH Line (Center mark position of the left-hand (LH) and right-hand (RH) headlights):

        Draw two vertical lines so that they intersect the H line at each center mark (aligned with the center of the low beam headlight bulbs).

  11. INSPECT FOG LIGHT AIMING (w/ Fog Light)


    1. Cover the fog light or disconnect the connector of the fog light on the opposite side to prevent light from the fog light that is not being inspected from affecting the fog light aiming inspection.

      Note

      Do not keep the fog light covered for more than 3 minutes. The fog light lens is made of synthetic resin, which may melt or be damaged due to excessive heat.

    2. Start the engine.

    3. except China and Taiwan:

      Turn on the fog light and check if the cutoff line falls within the specified area in the following illustration.

      Tech Tips


      • If the alignment distance is 25 m (82 ft.):

        The upper edge of the hot zone for the fog light should be 248 mm (9.76 in.) below the H line.

      • If the alignment distance is 3 m (9.84 ft.):

        The upper edge of the hot zone for the fog light should be 29 mm (1.14 in.) below the H line.

      A00XJQAE59
    4. for China and Taiwan:

      Turn on the fog light and check if the cutoff line falls within the specified area in the following illustration.

      Tech Tips


      • If the alignment distance is 10 m (32.8 ft.):

        The upper edge of the hot zone for the fog light should be 99 mm (3.89 in.) below the H line.

      • If the alignment distance is 3 m (9.84 ft.):

        The upper edge of the hot zone for the fog light should be 29 mm (1.14 in.) below the H line.

      A00XJQAE60
  12. ADJUST FOG LIGHT AIMING (w/ Fog Light)


    1. A00XI8ME01
      Text in Illustration
      *1 Aiming Screw

      Adjust the aim vertically.

      Adjust the aim of each fog light to the specified range by turning the aiming screw with a screwdriver.

      Note

      The final turn of the aiming screw should be made in the clockwise direction. If the screw is tightened excessively, loosen it, and then retighten it so that the final turn of the screw is in the clockwise direction.

      Tech Tips

      If it is not possible to correctly adjust fog light aim, check the bulb, fog light unit and fog light unit reflector installation.